Loading ...
Loading ...
Loading ...
,0
iiiiiiiiiiiiiii_i;_iiii!ii:i_iiiilililili_ii_ii_ii_ii_ii_ii_ii_ii{!;!!!j!ij
iiiiiiiiiiiiii::i_'iiiii_:ii:ii:ii:ii:iiiiii!ii!!
iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiililililililililiiiiiiii i!ill
,0
,0
-€
#_.
About theautomaticieemake
A newly instafled refrigerator may take 12 to 24 hours to begin making ice.
Automatic Icemaker
On dispenser models,
to access ice or reach
the power switch:
o Lift the bin, then pull it
forward until the bin stops.
Lower the bin to access ice
or reach the power switch.
NOTE:In order to take full advantage
of the tilt-out ice bin, only store items
on the shelf below the ice bfl?that
are no taller than the Iowest point
on the bh_.
Tile icemaker will produce seven cubes
per cycle---aI)I)ro_mately ] 00-130 cubes
in a 94-hem" period, depending on fl'eezer
COilli)ai'tlllent teillpei'attli'e_ i'OOill
temperatm'e, nmnber ot door openings
and other use conditions.
If tile refl_igerator is operated betore tile
water connect.ion is made to the icemaket;
set tile power switch in tile 0 (Of/) position.
When the reti-igerator has been com_ected
to tile water SUl)l)ly, set tile power switch to
tile I (on) position.
The icemaker will fill with water when it
cools to ] 5°F (-10°C). A newly installed
refi_igemtor may take 12 to 24 hems to begin
making ice cubes.
You will hear a buzzing so/md each time
the icemaker fills with water
Throw awax tile first troy batches of ice to
allow the water line to clea_:
Be sm'e nothing interteres with tile sweep
of tile teeler amL
When tile bin fills to tile level ot tile teeler
am_, tile icemaker will stop producing
ice. It is nom_al tin" several cubes to be
joined together.
If ice is not used fl'equentl> old ice cubes
will become cloudy, taste stale and shrink.
Special note about dispenser models:
Dispenser models have a tilt-out ice bin.
The bin can be tilted out as shown in the
illustrations, and it will hold itself up
while you take ice out or tm'n tile
icemaker power switch on and off'. Be
sm'e to put tile bin back in place before
closing the doo_:
To restore your ice level from an empty
bucket stage, the following steps are
recommended:
12 ho/us after the first batch of ice
has fifllen into the bin, dispense
3 to 4 cubes.
@ _MteI" an additional 6 hom_, dispense
3 to 4 cubes again.
These steps will restore your ice level
in the shortest amount of time.
Power
Switch
!cemaker
green
PowerLight FeelerArm
NOTE:/n homes with lower-than-averagewater
pressure,you mayhear the icemakercycle mult_}91e
t_meswhenmak/bg onebatch of ice.
i i
o Lift thebin, thenpull it
forward untilthe bin stops.
o Lift andpull forwardagain
to removethe bin.
Removing Ice Bin (dispensermodels)
gAUTlON: The ice bin is heavy when full.
SettheI,o,,'e,'switdlto theOtomI,ositi..
before relnoxing tile bin.
When replacing the bin, be sure to press it
firefly into place. If it does not go all tile
wa) back, remoxe it and rotate tile (lrixe
backmechanismagain. 1/4 turn. Then push tile bin
Dispenser Models only
14
Loading ...
Loading ...
Loading ...