Loading ...
Loading ...
Loading ...
13 DONOTusetheTableSawasa toy.DONOTuse
nearoraroundchildren.
27.NEVERperformlayout,assemblyorset-upworkon
thetable/workareawhenthemachineisrunning.
14.TheTableSawisdesignedforhomeuseor light
commercialdutyONLY.
28.NEVERresetthethermal-overloadbuttonbefore
youhaveturnedthetablesaw"OFF".
15.CONNECTTableSawto a properlygroundedoutlet
only.Seegroundinginstructions.
16.ALWAYSUSEtheguardswheneverpossible.
Checkto seethattheyarein place,securedand
workingcorrectly.
29.
30.
PROPERLY SUPPORT long or wide workpiece.
TURN THE SAW "OFF" and unplug from power
source. Clean off the table/work area before leav-
ing the saw. LOCK the START/STOP switch with
padlock provided to prevent unauthorized use.
17. AVOID KICKBACK by:
• Keeping blade sharp and free of rust and pitch.
• Keeping rip fence parallel to saw blade.
• Using saw blade guard and splitter assembly for
every possible operation, including all through-
sawing.
• Pushing the workpiece past the saw blade prior to
release.
• Never rip a workpiece that is twisted or
warped, or does not have a straight edge to guide
along the fence.
• Using featherboards when the blade guard and
splitter assembly cannot be used.
• Never sawing a large workpiece that cannot be
controlled.
• Never using the fence as a guide when cross-
cutting.
• Never sawing a workpiece with loose knots or
other flaws.
18. REMOVE cut-off pieces and debris from the table
before starting the saw. The vibration of the saw
may cause them to move into the saw blade and be
thrown out. After cutting, turn the saw off. When
the blade has come to a complete stop, unplug the
saw and remove all debris.
19. NEVER START the saw with the workpiece against
the blade.
20. NEVER perform "free-hand" operations. Use either
the fence or miter gauge to position and guide the
workpiece. Hold the workpiece firmly against the
miter gauge or fence.
21. USE a push stick(s) for ripping a narrow workpiece.
22. AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause a
hand to move into the blade.
23. KEEP arms, hands and fingers away from the blade.
24. NEVER have any part of your body in line with the
path of the saw blade.
25. NEVER reach around or over the blade.
26. NEVER attempt to free a stalled blade without first
turning the machine "OFF" and unplugging it from
the power source.
31.
32.
33.
34.
35.
ALWAYS position auxiliary fence at least 2-inches
in front of saw blade when using auxiliary fence as
a stop when cross cutting.
The right extension wing MUST BE completely
assembled and motor cover closed and fastened
before table saw is to be connected to the power
source.
DIRECTION OF FEED. Feed work into a blade or
cutter against the direction of rotation of the blade
or cutter only.
ADDITIONAL INFORMATION regarding the safe
and proper operation of this product is available
from the National Safety Council, 1121 Spring Lake
Drive, Itasca, IL 60143-3201 in the Accident
Prevention Manual for Industrial Operation and also
in the Safety Data Sheets provided by the NSC.
Please also refer to the American National
Standards Institute ANSI 01.1 Safety Requirements
for Woodworking Machinery and the U.S.
Department of Labor OSHA 1910.213 Regulations.
SAVE THESE INSTRUCTIONS. Refer to them
frequently and use them to instruct other users.
Information regarding the safe and proper operation of
this tool is available from the following sources:
Power Tool Institute
1300 Summer Avenue
Cleveland, OH 44115-2851
www.powertoolinstit ute.org
National Safety Council
1121 Spring Lake Drive
Itasca, IL 60143-3201
American National Standards Institute
25West 43rd. St, 4th Floor
New York, NY. 10036
ANSI 01.1 Safety Requirements
For Woodworking Machines
WWW.ANSI.ORG
U.S. Department of Labor Regulations
OSHA 1910.213 Regulations
WWW.OSHA.GOV
Loading ...
Loading ...
Loading ...