Loading ...
Loading ...
Loading ...
Loading ...
Loading ...
Loading ...
- Table of contents
- en-us Operating instructions
- ( Safety Definitions 5
- ( IMPORTANT SAFETY INSTRUCTIONS 6
- Æ Causes of Damage 9
- * Getting Started 10
- + Water softening system / special salt 12
- , Rinse Aid 14
- - Loading the Dishwasher 15
- . Detergent 25
- / Dishwasher Cycles 27
- 0 Dishwasher Cycle Options 28
- 1 Operating the Dishwasher 31
- 2 Care and Maintenance 36
- 3 Troubleshooting 40
- 4 Customer Service 44
- â¡ Statement of Limited Product Warranty 45
- ( Safety Definitions
- en-us Operating instructions
- ( IMPORTANT SAFETY INSTRUCTIONS
- To reduce the risk of fire, electrical shock, or serious injury, observe the following:
- GROUNDING INSTRUCTIONS
- Safe Operation
- Child Safety
- Proper Care and Maintenance
- 9 WARNING
- 9 WARNING
- Æ Causes of Damage
- * Getting Started
- + Water softening system / special salt
- Instructions for use of included âWater Hardness Test Stripâ
- 1. Run the water at the kitchen sink for 5 minutes.
- 2. Dip the end of the test strip with the colored squares into the tap water for 1 second and shake off excess water.
- 3. After one minute, compare the test strip to the chart below and determine the Dishwasher Water Softener setting.
- 4. Adjust the dishwasher Water Softener setting. ~ "Adjusting the water softening system" on page 13
- 5. If required, add salt to the dishwasher salt chamber as shown. ~ "Using special dishwasher salt" on page 13
- Instructions for use of included âWater Hardness Test Stripâ
- Adjusting the water softener settings
- Using the test strip included with your dishwasher (Purchased test strips may have a different scale)
- Water softener setting
- Add salt to salt dispenser
- Water hardness onversion chart (only necessary if you purchase a different test strip)
- ppm
- gpg/°dH
- Adjusting the water softening system
- Set the softening system as follows:
- 1. Ask your local water utility company for the water hardness value of your tap water.
- 2. Required setting can be found in the water hardness table.
- 3. Open the door.
- 4. Switch on On/Off switch (.
- 5. Hold down function key # and press Start button P until the display 8 indicates â¢:â¹x (x can be any number).
- 6. Release both buttons. The indicator of function key # flashes and the display 8 indicates â¢:â¹â¦. Press function key 3 to select the desired setting.
- 7. Save the selected setting by pressing the Start button P .
- Set the softening system as follows:
- Using special dishwasher salt
- Using detergents with salt component
- Switching off low salt indicator / water softening system
- , Rinse Aid
- Rinse Aid
- Note:
- Adding rinse aid
- NOTICE
- 1. Open the rinse aid dispenser 9* by pressing on the latch of the lid and pull it open.
- 2. Add liquid rinse aid to the dispenser 9* until it is full. Do not overfill.
- 3. Close the lid. Lid must be fully closed until it clicks in order to seal.
- 4. Wipe up any excess rinse aid that may have puddled when the dispenser reservoir is full.
- NOTICE
- NOTICE
- Setting the amount of rinse aid used
- Setting
- Amount
- 1. Open the door.
- 2. Press the On/Off button (.
- 3. Hold down function key # and press Start button P until the display 8 indicates â¢:â¹x (x can be any number).
- 4. Release both buttons. The indicator of function key # flashes and the display 8 indicates the factory set value â¢:â¹â¦
- 5. Press the function key # until the display 8 shows §:â¹â .
- 6. Press function key 3 to select the desired setting.
- 7. Press Start button P to save the setting.
- Turning off rinse aid indicator
- - Loading the Dishwasher
- Adjusting the water softening system
- 9.4 in (24 cm)
- 13.4 in (34 cm)
- 10.4 in (26.5 cm)
- 12 in (30.5 cm)
- 11.4 in (29 cm)
- 11 in (28 cm)
- 7 in (18 cm)
- 13.4 in (34 cm)
- 8 in (20.5 cm)
- 12 in (30.5 cm)
- 9 in (23 cm)
- 11 in (28 cm)
- RackMatic®
- Rack accessories
- Removing/Installing third rack
- Removing third rack 1*
- Installing third rack 1*
- 1. Pull out third rack rails all the way (1).
- 2. Insert third rack at an angle. Make sure that the stopper hooks of both rails slide in between the holding hooks and the lower rollers of the third rack (2).
- 3. Slide third rack in and lift the upper rollers over the front stopper hooks of both rails (3).
- 4. Push in third rack (4).
- Removing/Installing upper rack with Rackmatic®
- Removing upper rack 12
- Installing upper rack 12
- 1. Pull out upper rack rails all the way (1).
- 2. Insert upper rack at an angle. Make sure that the stopper hooks of both rails slide in between the upper and lower rollers on the rear side of the rack (2).
- 3. Slide upper rack in and lift the upper rollers over the front stopper hooks of both rails (3).
- 4. Push in upper rack (4).
- . Detergent
- / Dishwasher Cycles
- The Energy Guide label was based on the Normal soil sensing cycle as follows: The unit was tested without any rinse aid (liquid) in the rinse aid dispenser 9*. A single dose of detergent was inserted into the detergent dispenser 92, with no detergent...
- Only sanitizing cycles have been designed to meet the requirements of Section 6 of the NSF/ANSI Standard for Residential Equipment for soil removal and sanitization efficacy. There is no intention, either directly or indirectly, to imply that all cyc...
- 1 Operating the Dishwasher
- Operating the Dishwasher
- Note:
- 9 WARNING
- Protection against unintentional operation
- Operating the touch buttons
- AquaSensor
- Switching the appliance on
- Time display
- Delay Start
- Wash cycle end
- To change the signal volume:
- 1. Open the door.
- 2. Press the On/Off button (.
- 3. Hold down function key # and press Start button P until the display 8 indicates â¢:â¹x (x can be any number).
- 4. Release both buttons. The LED for function key # flashes and teh digital display shows the factory setting â¢:â¹â¦.
- 5. Press function key # until the display shows âº:â¹Æ.
- 6. Press function key 3. Each time the button is pressed the set value increases by one level; when it reaches the value âº:â¹â, the display jumps back to âº:â¹â¹ (off).
- 7. Press Start button P to save the setting.
- To change the signal volume:
- Auto power off
- To change the setting:
- 1. Open the door.
- 2. Press On/Off button (.
- 3. Hold down function key # and press Start button P until the display 8 indicates â¢:â¹x (x can be any number).
- 4. Release both buttons. The indicator of function key # flashes and the display 8 indicates the factory set value â¢:â¹â¦
- 5. Press function key # until the display 8 indicates Ë:â¹x.
- 6. Press function key 3 until the display corresponds with your requirements.
- 7. Press Start button P.
- To change the setting:
- Switching off the appliance
- Interrupting the wash cycle
- 9 CAUTION
- Cancel a cycle (Reset)
- Changing the wash cycle
- Intensive drying
- To change the setting:
- 1. Open the door.
- 2. Press On/Off button (.
- 3. Hold down function key # and press Start button P until the display 8 indicates â¢:x (x can be any number).
- 4. Release both buttons. The indicator of function key # flashes and the display 8 indicates the factory set value â¢:â¹â¦
- 5. Press function key # until the display 8 indicates the factory set value Å¡:â¹â¹.
- 6. Press function key 3 to switch the feature on Å¡:â¹â or off Å¡:â¹â¹.
- 7. Press Start button P to save setting.
- To change the setting:
- TimeLight® (Optical display while the wash cycle is running)
- All time remaining displays
- To change the setting:
- 1. Open the door.
- 2. Press On/Off button (.
- 3. Hold down function key # and press Start button P until the display 8 indicates â¢:x (x can be any number).
- 4. Release both buttons. The indicator of function key # flashes and the display 8 indicates the factory set value â¢:â¹â¦
- 5. Press function key # until the display 8 indicates the factory set value â :â¹â.
- 6. Press function key 3 to switch between â :â¹â¹, â :â¹â and â :â¹Æ.
- 7. Press Start button P to save setting.
- 2 Care and Maintenance
- Care and Maintenance
- Overall condition of the dishwasher
- Filters
- Filter components
- The filter system 1b consists of three parts.
- Cleaning intervals
- Cleaning interval
- Use this setting,
- To check or clean the filter system:
- 1. Unscrew the Large Object Trap as illustrated and remove the entire filter system.
- 2. Remove any residue and clean filters by rinsing under running water. Note: do not use abrasive brushes or steel wool, etc., as they may damage the filter.
- 3. Reinstall the filter system in reverse sequence and lock into place by screwing the Large Object Trap until the marking arrows align.
- Spray arms
- Drain pump
- Preparing your unit for vacation
- Winterizing your unit
- 3 Troubleshooting
- --------
- 4 Customer Service
- â¡ Statement of Limited Product Warranty
- 1 Operating the Dishwasher
- Page 49/52 Page 1Page 2Page 3Page 4Page 5Page 6Page 7Page 8Page 9Page 10Page 11Page 12Page 13Page 14Page 15Page 16Page 17Page 18Page 19Page 20Page 21Page 22Page 23Page 24Page 25Page 26Page 27Page 28Page 29Page 30Page 31Page 32Page 33Page 34Page 35Page 36Page 37Page 38Page 39Page 40Page 41Page 42Page 43Page 44Page 45Page 46Page 47Page 48Page 49Page 50Page 51Page 52
- Contents
- Table of Contents
- Search
- Previous
- Next
- Troubleshooting
- Bookmarks