Loading ...
Loading ...
Loading ...
7
Installation
, WARNING:
Do not install the appliance:
outdoors,
in an environment with dripping water,
in rooms which are less than 32 °F (0 °C).
Appliance is very heavy:
Refrigerator 24" approx. 310 Ibs/140 kg
Refrigerator 30" approx. 350 Ibs/158 kg
Freezer 18" approx. 255 Ibs/115 kg*
Freezer 24" approx. 300 Ibs/135 kg*
Freezer 30" approx. 335 Ibs/150 kg*
Wine unit 18 "approx. 300 Ibs/135 kg
Wine unit 24 "approx. 360 Ibs/160 kg
(* without Water Dispenser)
Installation room
The appliance should be installed in a dry, ventilated
room.
The ambient temperature should not drop below 55 °F
(13 °C) or rise above 110 °F (43 °C), otherwise
malfunctions may occur.
The installation location should not be exposed to direct
sunlight and not placed near a heat source, such as an
oven, radiator, etc. If installation next to a heat source is
unavoidable, use a suitable insulating plate or observe
the following minimum distances from the heat source:
1
1
/
4
" (30 mm) from an electric range,
12" (300 mm) from a gas range.
Stable installation
The appliance is very heavy and has a tendency to tilt
forwards when the appliance door is opened.
Do not open the door until there is no possibility of the
appliance tilting over.
The safest method of installing the appliance in a stable
position is to use the supplied anti-tip devices.
If the installation enclosure is adequately stable and the
appliance can be attached securely to the upper and
side walls of the installation enclosure, this may provide
additional stability. A prerequisite for this is always a firm
connection between the installation enclosure and back
wall!
If in doubt, contact an architect or a building expert.
Installation enclosure
Note:
It is strongly recommended the top panel of the niche be
of solid material at least
5
/
8
" (16 mm) thickness. If, for
some reasons, a seperate niche cabinet is created, make
sure that the furniture return area is at least 4" deep.
It is important to observe the specified dimensions of the
installation enclosure for a trouble-free installation of the
appliance.
In particular ensure that the installation enclosure is
square.
Squareness can be checked by suitable means,
e.g. level, diagonal measurements, etc.
Furniture
The new appliance must be screwed securely to
adjacent and overhead furniture.
For this reason it is essential that all attachable furniture
are connected securely to the floor or the wall by suitable
means.
Floor
,
WARNING:
A fully-loaded appliance is very heavy – for the
loadbearing capacity minimum see the following:
Refrigerator 24" approx. 890 Ibs/400 kg
Refrigerator 30" approx. 1110 Ibs/500 kg
Freezer 18" approx. 560 Ibs/250 kg*
Freezer 24" approx. 780 Ibs/350 kg*
Freezer 30" approx. 950 Ibs/425 kg*
Wine unit 18" approx. 550 Ibs/245 kg
Wine unit 24" approx. 694 Ibs/310 kg
(* without Water Dispenser)
To ensure that the appliance is installed securely and
functions properly, the floor must be flat and level.
The floor must be made of a hard, rigid material.
The floor in the installation area must be at the same
level as the rest of the room (no step up or down).
On account of the heavy weight of a fully loaded
appliance, a load-bearing floor is required. If in doubt,
contact an architect or a building expert.
Aligning the appliance
To ensure that the appliance functions correctly, it must
be levelled properly.
If the appliance is not level, water may flow out of the ice
maker, ice cubes may be irregular or the doors may not
close properly.
Loading ...
Loading ...
Loading ...