Loading ...
Loading ...
Loading ...
6
7. Close both doors and check that they close as easily as
you like. If not, turn both screws to the right to raise the
refrigerator by tilting it more to the back until the doors close
as easily as you like.
8. Check and make sure that the technician sheet is placed in
the base grille cavity before assembling this into the cabinet
9. Reinstall the left side of the base grille into the cabinet first,
and then the right side. See graphic 3. You may insert the
water dispenser tubing and wiring into the base grille cavity
below the left bottom hinge.
10. Attach the base grille by pushing it into the cabinet clips.
See graphic 2.
Door Alignment
The refrigerator doors are designed to be slightly misaligned
vertically when the refrigerator is empty. Please follow the next
steps to align the refrigerator doors.
1. Use an 11/16" open-ended wrench tool to loosen the locking
nut located below the refrigerator door. See graphic 11.
Accommodate the wrench tool so that it fits in the space.
2. Use a 5/16" open-ended wrench tool to turn the alignment
screw. See picture 12. Depending on how the refrigerator
door is misaligned in relation to the freezer door, you
must turn the screw to the right to raise or to the left to
lower the refrigerator door until both doors have been
aligned vertically.
3. Tighten the 11/16" locking nut with the wrench tool.
4. Attach the base grille if it was dislodged.
Handle Installation and Removal
PARTS INCLUDED: Door handles (2)
To Install the Handles:
1. Remove the handles, which are packed inside the
refrigerator.
NOTE: To avoid scratching the finish, place the handles on
a towel or other soft surface.
2. Open the freezer door. On the refrigerator door, place the
handle on the shoulder screws.
A
A. Shoulder screws
3. Firmly push the handle toward the door until the handle base
is flush against the door.
4. While holding the handle, push downward until the handle
rests firmly on the shoulder screw.
5. Open the refrigerator door and close the freezer door.
Repeat steps 2 through 4 to install the other handle onto
the freezer door.
To Remove the Handles:
1. While holding the handle, push upward until the handle is
realeased from the shoulder screw.
2. Gently pull the handle away from the door.
3. If necessary, use a Phillips screwdriver to remove the
shoulder screws from the door.
Location Requirements
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
IMPORTANT: This refrigerator is designed for indoor household
use only.
To ensure proper ventilation for your refrigerator, allow for
1/2" (12.7 mm) of space on each side and at the top. Allow for
2" (50.8 mm) of space behind the refrigerator. If your refrigerator
has an ice maker, allow extra space at the back for the water
line connections. When installing your refrigerator next to a
fixed wall, leave a 2" (50.8 mm) minimum space on each side
(depending on your model) to allow the doors to swing open.
NOTES:
■ This refrigerator is intended for use in a location where the
temperature ranges from a minimum of 55°F (13°C) to a
maximum of 110°F (43°C). The preferred room temperature
range for optimum performance, which reduces electricity
usage and provides superior cooling, is between 60°F (15°C)
and 90°F (32°C). It is recommended that you do not install
the refrigerator near a heat source, such as an oven or
radiator.
■ Normal minimum cabinet cut-out width required for product
installation is 36" (91.44 cm). However, if the product is
placed against an extended wall and the ability to remove
the crisper pans is desired, an additional 18" (45.72 cm) of
cabinet width is required, so a total cabinet opening width of
54" (137.16 cm) is recommended.
1/2" (12.7 mm)
2" (50.8 mm)
Loading ...
Loading ...
Loading ...