Loading ...
Loading ...
Loading ...
Usingthe Wall-MountedDoorControl
THEMOTIONDETECTINGCONTROLCONSOLE
Pressthe push barto open or close the door. Press again to
reversethe door during the closing cycle or
to stop the door while it's opening. _y_,_Push
This door control contains a motion detector __jBar
that will automatically turn on the light when
II
it detects a person entering the garage. This J_Lock
feature can be easily turned off for extended _Jj_LButt°n
I_" Light
work light use. II Button
Lightfeature
Pressthe Light button to turn the opener
light on or off. It will not control the opener lights when the door is
in motion. If you turn it on and then activatethe opener, the light
will remain on for 4-1/2 minutes. Press again to turn it off sooner.
The 4-1/2 minute interval can be changed to 1-1/2, 2-1/2, or 3-1/2
minutes as follows: Press and hold the Lock button until the light
blinks (about 10 seconds). A single blink indicates that the timer
is reset to 1-1/2 minutes. Repeatthe procedure and the light will
blink twice, resetting the timer to 2-1/2 minutes. Repeatagainfor
a 3-1/2 minute interval, etc., up to a maximum of four blinks and
4-1/2 minutes.
Automaticlight feature:The opener light will turn on automatically
when a person enters the garage.When a person walks in front of
the door control, the lightwill come on for five minutes, then shut
off. This featureworks by detecting body heat and may not work in
temperatures around 100° F (37.7° C).To disable this feature, slide
the detector switch on the right side of the door control down (off).
We recommend that you disable the motion sensor when using
the opener lightsas working lights.Otherwise, they will turn off
automatically if you are working beyond the sensors range.
Lockfeature
Designedto preventoperation of the door from hand-held
remote controls. However, the door will open and close from
the Door Control, the Outdoor Key Switch and the KeylessEntry
Accessories.
To activate, press and hold the Lock button for 2 seconds.The
push button light will flash as long as the Lockfeature is on.
To turn off, press and hold the Lock button again for 2 seconds.
The push button light will stop flashing. The
Lock feature will also turn off wheneverthe
"learn" button on the motor unit panel is
activated.
Additionalfeature when used with the
3-Functionhand-heldremote
To control the openerlights:
In addition to operating the door, you may program the remote to
operate the lights.
1. With the door closed, press and hold a small remote button that
you want to control the light.
2. Press and hold the Light button on the door control.
3. While holding the Light button, press and hold the Lock button
on the door control.
4. After the opener lights flash, releaseall buttons.
To Openthe DoorManually
To prevent possible SERIOUSINJURYor DEATHfrom a falling
garagedoor:
• If possible, use emergency releasehandleto disengage
trolley ONLYwhen garage door is CLOSED.Weakor broken
springs or unbalanceddoor could result in an open door
falling rapidly and/or unexpectedly.
• NEVERuse emergency releasehandle unless garage
doorway is clear of persons and obstructions.
• NEVERuse handleto pull door open or closed. If rope knot
becomes untied, you could fall.
DISCONNECTTHETROLLEY:
The door should be fully closed
if possible. Pull down on the
emergency releasehandle (so
that the trolley releasearm snaps
into a vertical position) and lift
the door manually. The lockout
Trolley
Trolley
Release Arm
feature prevents the trolley from (In Manual
Disconnect
reconnecting automatically, Position)
and the door can be raised and
lowered manually as often as _ ,,_
necessary. Lockoutposition
(Manual disconnect)
TORE-CONNECTTHETROLLEY:
Pull the emergency release
handletoward the opener at an
angle so that the trolley release
arm is horizontal. The trolley
will reconnect on the next UP
or DOWNoperation, either
manually or by using the door
control or remote.
Trolley
_e
Emergency """ "_t11__Arm
Release Handle _ '_, ._
(Down and Back),_._'
TOreconnect
31
Loading ...
Loading ...
Loading ...