REMIN N
8' ELECTRIC=TElESCOPING POLE SAW
INTRODUCTION
YourRemington Telesooping Pole Saw is a
dual purpose product. The electric chain
saw is a separate operating unit when not
assembled to the telescoping pole. Before
operating either the chain saw or the Pole
Saw, make certain you readand understand
all Safety Warnings.
A SAFETY
WARNINGS
Make Certain you read and
understand all Safety Warnings
on pages 2 and 3. Improper use
ofthis Pole Saw can cause severe
injury or death from fire, electrical
shock, body contactwRh moving
chain, or falling wood.
BEFORE OPERATING SAW
1. Read and understand both chain saw
and Pole Saw manuals before operat-
ing saws.
2. Watch what you are doing. Usa com-
mon sense. Do not operate saw when
you aretired.
3. Use chain saw for cutting wood only.
Do not use chain saw for purpose not
intended. Do not use for cutting non-
wood items.
4.
Only well-iusmtcted adults should op-
erate Pole Saw orchain saw. Nero al-
low children to operate saws.
5. Use only electrical voltage noted on
model plate of chain saw..
6. Use only extension cords marked for
outdooruse. See Operating Chain Saw
section of chain saw manual for exten-
sion cord requirements,
7. Do not operate Polo Saw orchain saw
• while under the influence of alcohol,
medication, or drugs
• in rain orin damp orwet areas
• if tfiggex does not turn saw on and
off. Chain must stop moving when
you release trigger. Haye faulty
switch replaced byauthorizedservice
center.See chain saw manual forlist-
ing of authorized service centers.
• whiin in a hurry
• wl_e in tree or on a ladder
• while on aerial booms, buckets or
5.
pisiforms
8. Wearsung-fittlng clothes when oper-
ating Pole Saw or chain saw. Do_not
wear loose clothing or jewelry. They 6.
can get caught in moving saw chain.
9. Wearthe following safety gear when 7.
operatingsaws:
• heavy-duty gloves (wear rubber
gloves when working outdoors) 8.
• steel-toed safety footweur with non-
skid soles 9.
• eyeprotection such as safety glasses,
goggles, or face screen 10.
• safetybardhat ,
• earmufflers orear plugs
• haircoveting to contain long hair 11.
• faceordust mask (ifwortdng in dasty
areas)
10. Before cutting, always provide the fol- 12.
lowing:
• clearwork area
• secure footing
• planned retreat path from falling 13.
limbs
II. Inspecttree hefore trimming. Make al-
lowance for branches to fall freely to
the ground.
12. Do not Use your Polo Saw to fell sap- 14.
lings. Use the chain saw without pole
attachemenL.::7"i _
13. To reducethe risk of electric shock, this
saw has a polarized plug (one blade is
widerthan the other). This plug will fit
in a polarized oudet only one way. If
the ping does not fit fully in the oudet
of your extension cord, reverse the
plug. If it still does not fit, a polarized 15.
extension cord will be necessary. Do
not change the plug in any way.
• where highly flammable liquids or
gasesarapresent WHILE OPERATING POLE SAW
• if pule or saw is damaged, edjusted ....... ,.... -_- ..........
1. Ot_y tutti* Ub_ _;UI_dLUUU _cnse willie
wrong, or not fully and securely ..... -_pe._dn_ _uni-L ............
assembled • - "="-" _`
2. Keepwork areaclean.Clutteredareas
inviteinjuries.
3. Be aware ofexteusion cordwhile op-
orating chain saw. Be cerefiq not totrip
over €ord.Keep cordawa'. _m chain
and operatorat all times.
- 4. Keep children, animals, and bystand-
ers away from Pole Saw andextension
cord.OnlyPoleSaw usershouldhein
work area.
Do not use the Pole Saw to cut down
trees. Use the chain saw without pole
attachment and only if you aretrained
or have expert help.
Do not use near power lines. Keep at
least I0 feet away fromelectricallines.
GripPoleSaw securely-onehandon
thepole,theotheronthehandle.
Keep fingeroff_gges undlreadyto
make cut.
BeforestartingPoleSaw,make sure
chainisnottounldnganything.
Toguardagainstelec=icalshock,avoid
body contactwithgroundedobjects
suchaspipes,fences,andmetalposm.
Keepallparrsofbodyawayfromchain
when saw isrunning.
Do not force chain saw while cutting.
Apply light pressure.It will do thejob
better andsafer at the rate forwhich it
was intended.
When cuttinglimbortreetrunkthatis
under tension, use extreme caution.Be
alert for wood springingback. When
wood tensionisreleased,limbcould
springbackand strikeoperatorcaus-
ingsevereinjuryordeath.
CarryPoleSaw fromoneplacetoan-
other
• withunitunplugged
• with telescoping pole returned to
shortest position
• by holding pole at balance point
(close to saw end)
• with guide bar and chain to rear
Do notcutsmallbrushand saplings
with the Pole Saw. Use the chainsaw
only, with extreme care. Slender mat-
ter may catch in the chain and be
whippedtoward you.Thiscouldalso
pull youoff balance.
OWNER'S MANUAL
SAFETY
WARNINGS
continued
KICKBACK
_WARNING: Kickback may oc-
cur when the nose or tip of the
guide bar touches an object, or
when the wood closes In and
pinches the saw chain in the cut.
Tip contact in some cases may
cause a lightning fast reverse
reaction, Idcldng the guide bar
up and back towards the opera-
tor, Pinching the saw chain along
thetop of the guide bar may push
the guide bar rapidly back to-
wards the operator. Either of
these reactions may cause you
to lose control of the saw which
could result in serious Injury to
user.
Kickback Safety Devices On
This Saw
This saw has a low-kickback chain and
reducedkickbackguidebar.Both items
reduce the chance of kickback, however,
kickback can still occur with this saw.
The following steps will reduce the risk of
kickback..
• Use both hands- one gripping the han_e
andtheotherg_ppingthepole.Usefirm
grip. Thumbs and fingers must wrap
around pole andhandle.
• _ep,..a]lsafeP]items in place on saw.
Make sum they work properly.
• Do not overreach or extend arms above
shoulder height.
• Keep solid footing and balance at all
times.
• Never try cu_ingthroughtwo branches
at the sametime. Only cutone ata time.
• Do not burygnidebar neseorIzyplunge
cut (boring into wood using guide bar
nose).
• Watch for sldt'tingof wood or other
forces thatmay pinch chain.
• Use ex_¢me caution when re-entering a
previous
• Use low-kickbackchainand guidebar
suppliedwiththechain saw, Only use
replacementpartsListedf_ the polesaw.
• Neveru_ dni]c_loo_ chain.Kecp chain
sharp and adjusted correctly.
Saw Maintenance and Kickback
Safety
Followmaintenanceinstxuctiousinthechain
saw manual.Propercleaning of saw and
chainandguidebarmaintenancecanreduce
chancesofkickback.Inspectandmaintain
saw after each use. This will increase the
service life of your saw, Note: Even with
propersharpening,riskof kickbackcan
increase with each sha_aning..
MAINTENANCE
AND STORAGE OF
POLE SAW
UnplugPoleSaw frompower sourceand
followmaintananc¢ andstorageprocedures
outlined in the Maintenance and Storage
section of yoor chain saw manual.
POLE SAW
TRIMMING
PRECAUTIONS
Never stand directly under the limb
you are trimming. Always position
yourself out of the path of falling
debris.
Never stand on a ladder or other type
of unstable support while using the
Pole Saw.
Always use both hand_ to operate
Pole Saw. Keep a firm, steady pres-
sure on the Pole Saw while cutting
but do nottry toforce the sawthrough
the wood.
Do not use the Pole Saw to cut limbs
larger in diameter than the length of
the guide bar.
Keep other persons away from cut-
ting end of polesaw and at a safe
distance from work area.
Do not use Pole Saw near cable, elec-
tric power or telephone lines. Main-
taln a mlni_num ciea-rance-of 10 f_t
from all power lines.
Io_ 3
REMIN N
8' ELECTRIC TELESCOPING POLE SAW
PRODUCT
IDENTIFICATION
HandGuard
\
Saw Chain
Gr_Area
Power
Cor_
Coupling_.
Nut
Inner Pole
GuideBar
HandleBracket
OuterPole
Tdgger
Switch
Lock-out
_Power Cord
Figure 1-Pole Saw Product Identification
POLE SAW NAMES
AND TERMS
Coupling Nut Thieadedcollar(loosento
slide inner pole, dghtea to hold pole in
position).
Guide Bar Metal bar thatextends from
saw body. The guide bar supports and guide*
chain.
Inner Pole The moveable section of rob-
ing m which the saw is attached.
Kickback Quick backward and upward
motion of guide bar. Kickback may occur
when tip of guide bar touches an object
wkile chain is moving. The guide bar will
kick up and back towards operator.
Oiler Control System for oiling guidebar
andchain.
Outer Pole Retains themoveable inner
pole.
Saw Chain (Chain) Loopofchef.ring
cutting teeth for cutting wood. The motor
ddve.sChain.The guidebarsupports chain.
Sprocket Toothed wheel thatdrives chain.
Switch Device thatcompletes orinterrupts
electrical circuit to motor of saw.
Switch Lockout Devine that reduces
accidentalstartingof saw.
Trigger Device that turnssaw on and off.
Squeezing trigger turns saw on.
Releasing trigger turnssaw off.
Trimming (Pruning) Processof cutting
limb(s) from a living tree.
Undercut An upward cut fzom underside
of log or limb. This is done while in normal
cutting position and cutting with top of
guide bar.
UNPACKING
1. Remove allitems from carton.
2. Chock allitems for any aldpp'mg dam-
age, If you find any damage or ff any
parts are missing, promptly inform
deelar where you bought the Pole Saw.
ASSEMBLY
The plastic hardware bag for the Pole Saw
should include the following:
CHAIN SAW HARDWARE
(2) Guidebar bolts
• (2) Guidebar outs
• (1) Phillips sdftapping screw
• (1) Saw chain
• (I) Guide bar
• (1) Hand g_rd
• (1) Scabbard
POLE SAW HARDWARE
• (1) Handlebracket
• (4) #I0 x 24 Phlnlpsscrews
• (4) #101ockwashers
ASSEMBLY OF CHAIN SAW
Asserable the chain saw before assembling
the pole. Refer to chain saw manual for
assembly iustructions.
,_ CAUTION: Do not place chain
on saw backwards. If chain is
backwards, saw will vibrate badly
and will not cut.
F
Make sure cutting edges of chain arefacing
in the right direction. Position chain so cut-
flog edges ontop of guide barface gradebar
nose (see Figure 2).
Towards Cutting
GuideBar. ",Edge
Nose
Edge
Chain
F?gum2- Chain Position
OWNER'S MANUA
SAW CHAIN TENSION
ADJUSTMENT
WARNING: Maintaln proper
chain tension. A loose chain will
increase the risk of kick back. A
loose chain may jump out of
guide bar groove. This may in-
jure operator and damage chain.
A loose chain will cause chain,
guide bar and sprocket to wear
rapidly.
1. To adjust chain tension, make sure
guide bar nuts are only finger fight.
Also make sure adjusting block is in
oval adjust_g hole on guide bar.
2. Turn adjusting screw cIockwlsu until
all slack is out of chain. Note: Them
should be no gap between side links of
chain and bottom of guide bar.
3. Wearing protectivegloves,move chain
aroundguidebar. Chain should move
freely. If chain does not move freely,
loosen chainby turningadjusting screw
counterclockwise,
.
After chain tension is correct, tighten
guide barnutsfirmly. If not, guide bar
will move and loosen chain tension.
This will increase the risk of kickback.
This can also damage saw.
ASSEMBLY OF POLE SAW _'/:
• l. Slip handle bracket over chain saw
handle fromthe fightside (seeHga_ 5).
Note: The trigger must be depressed
before the bracket will go onto the
handle,
• Push the lockout buttonanddepresstbe
trigger, While holding the trigger in,
place the trigger supportportionof the
bracket under the triggerand slide the
bracket onto the chain saw handle.The
bracket will keep thetriggerin the "on"
posifiou,
2_ Align holes in pole bracket with holes
in handle bracket. InstallPhillips head
screws with lcokwasb_ throughpole
bracketfromleft side and threadinto
theweld nutson thehandlebracket.
Tightenscrewssecurelybyhand.
3. Plugthesawpowercordintoreceptacle
cordatendofinnerpole.
Bracket
Trigger
Support
Figure 5 -Bracket with Trigger Support
Figure3 - Turning Adjusting Screw
incorrectTension
Figure4 - Saw ChainAdjustment
Figure 6- AssemblyofPoleSawBrackef
to,_ 5
REMIN N!
8' ELECTRIC TELESCOPING POLE SAW
OPERATING PoLE
SAW
WARNING: Read end under-
stand this owner's manual be-
fore operating this Pole saw.
Make certain you read and un-
derstand all Safety Warnings.
Improper use of this Pole Saw
can cause severe in)ury or death
from fh'e, electrical shock, or body
contact with moving cha|n, or
falling wood.
EXTENSION CORDS
Use properextensioncordswiththisPole
Saw.Use onlyextensioncordsmarkedfor
outdooruse.The cordmustbemarkedwith
suffixW orW-A followingthecordtype
designation.Example:SJTW-A orsyrw.
Use propersizecordwiththissaw.Cord
must be heavy enough to carrycurrent
needed.An undersizedcordwillcausevolt-
age dropatsaw.Saw willlosepowerand
overheat. Follow cord size requ£rements
listed below.
Cord Length AWG cord size
25 feet 16
50 feet 16
1oofeet 14
150 feet 12
Keep cordaway fromcuUingarea.Make
surecorddoesnotcatchonbranchesorlogs
duringcutting.Inspectcordsofinu.Replace
damaged cords.The extensioncordmay
come undonefrom thepowercordduring
use.To avoidthis,make aknotwiththetwo
cords as shown in Pigum ?.
Extension ChainSaw
Figure 7- TyingExtensionCordand Power
Cord In Knot
ADJUSTING POLE LENGTH
The RemingtonPoleSaw hasatele,_oping
pole assemblythatwin extend _ 57
inches(fullyretracted) to96 inches(fully
extended).A threadedcompressioncou-
plingis used to hold the polein position at
any extendedlength.
1. To extendthepole,loosencouplingby
turning couplingnut €ountemlockwise
asshowninFigure8.Polewillslide
freely.
2. Pullinnerpolesectionouttodesired
length ofexteusinn. Note:Only extend
pole to minimum length required to
reachlimbthatisbeingcut.
3. To lockpoleinposition,tightencou-
plingbyturningcouplingnu_clockwise
(see Figure 8) un_ _mIy hand tight.
Maim suresawhandle is alignedwith
pole handle before tightening coupling
nut. IMPOFfFANT:Do not use wrench
orpliers toove_ghtea coupling. Dam-
age to coupling orpole may result.
UNLOCK LOCK
Figure 8 - Extending TelescopicPole
OILING CHAIN
To oilchain,pressoilcap.Oilwillfeedonto
guidebarandchain.Pressoilcapat least
oncebeforeeachcut.Alwayscheckoillevel
beforeusingPoleSaw.Checkoilleveioften
bylookingatoilsightlevelhole.Oilsight
level hole is on left side of saw, between
front handle and front hand guard. Do not
attempt to operate the oiler while cutting
with the Pole Saw.
CUTTING WiTH THE POLE
SAW
I. Connectsaw toextensioncord_Con-
nect extension cord to power supply.
2. Use beth hands togrip Pole Saw. Use
only designated grip areaswhen oper_
atingPole Saw (see Fignre 9). Use firm
grip. Thumbs and fingers must wrap
aroundPole Saw handle and pole.
3. Make s_e your footing is firm. Keep
feet apart. Divide your weight evenly
on both feet.
4. Whea reedytomakeacat,pressintrig-
gerswitchlock-outandsqueeze_g-
ger switch(seeFigure10).Thiswill
turnPoleSaw on.Releasingu-igger
switchwillturnPoleSaw off.Make
suresaw isrunningatfullspeedbe-
forestarlingacot.
5. When startinga cut,placemoving
chainagainstwood.HoldPoleSaw
firmlyinplacetoavoidpossiblebounc-
ingorskating(sidewaysmo,iameat)of
saw.
.
GuidePoleSaw usinglight pressure.
Do notforcePoleSaw.Themotorwill
overloadandcanbum out.Itwilldo
thejobbetterandsaferattheratefor
whichitwasintended.
. Remove Pole Saw fromacut with saw
runningatfullspeed. Stop Pole Saw
byreleasingtrigger.Make surechain
hasstoppedbeforesettingPoleSaw
down.
Figure 9 - DesignatedGdp Areas
TriggerSwRch_"
Figurelo.Polesa,,,en ie
Switch Lock-out
OWNER'S MANUAL
OPERATING POLE
SAW
Continued
TRIMMING A TREE
PRUNING)
WARNING: Avoid kickback.
Kickback can result in severe in-
jury or death. See Kickback, page
3, to avoid risk of kickback.
_ WARNING: D_) not operate
Pole Saw while in a tree, on a
ladder or any other unstable work
surface, or in any awkward posi-
tion. You may lose control ofPole
Saw causing severe injury.
*(_ WARNING: Do not extend
arms above shoulders when us-
ing Pole Saw.
CAUTION: Seek professional
help if facing conditions beyond
your ability.
Tdmmlng a treeistheprocc,ssofcutting
limbsfromalivingt_e.Make surefooting
is firm. Keep feet aparLDivide your weight
evenly on both feet.
1. Make firstcut six inches f_omtree trdnk
on underside of limb. Use top of guide
bar to make this cut. (Cut I/3 through
diameter of limb, see figure Il).
2. Move two to four inches fartherout on
limb. Make second cut from above
limb. Continue cut until you cut limb
off.
3. Make third cut as close to tree trunkas
possible on underside of limb stub. Use
top of guide bar to make this cut. Cut
1/3 through diameter of stub.
4. Make fourth cut directly above third
cut. Cut down to meet third cut. This
will remove limb stub.
2rid Cut.
i I Pmn.ingCut
I I( 2.io,.
1st Cut-
-._ PruningUndercut
(toavoidsplintedng)
3rd Cut- Stub Undercut
(toavoidsplintering)
Figure 11 - CuttingA Limb
_ 7
CONTENTS
SAFETY
WARNINGS
Make certain you read
and understand all
Safety Warnings on
pages 2 through 5.
Improper use of this
chain saw can cause
severe injury or death
from fire, electrical
shock, body contact
with moving chain, or
falling wood.
m_
SECTION PAGE
Safety Warnings ............................................................................ 2
Before Operating Chain Saw .................................................. 2
Kickback ................................................................................. 3
Pushback and Pull-in .....; ......................................................... 4
Chain Saw Operation ............. :................................................ 5
Maintenance and Storage of Chain Saw ................................ 5
Product Identification .... .................................... :........................... 6
Chain Saw Names and Terms ....... ................................................. 7
Unpacking ...................................................... ................................ 8
Assembly ....................................................................................... 8
Saw Chain Tension Adjustment .................................................... l0
Filling Oil Tank ............................................................................. l 1
Operating Chain Saw ..................................................................... 12
Extension Cords ............................................................ :......... 12
[ Oiling Chain ........................................................................... 12
I Cutting With the Chain Saw ................................................... 13
Trimming aTree ..................................................................... 14
Felling a Tree ............................... :.......................................... 15
Limbing a Tree ........................................................................ 17
Bucking a Log ......................................................................... 18
Cleaning and Maintenance ............................................................ 20
Cleaning Saw Body ................................................................. 20
Care of Guide Bar ................................................................... 20
Sharpening Your Saw Chain (Non-Fast Sharp Model) .......... 21
Sharpening Your Saw Chain (Fast Sharp Model) ................... 24
Storage...........................................................................................25
Troubleshooting..................................................:..........................26
TechnicalService..................._......................................................27.
ServicePublications......................................................................27
RepairService...............................................................................27
ReplacementPartsand Accessories..............................................28
PartCentrals..................................................................................29
AuthorizedServiceCente_ ........................_..................................29
WarrantyInformation....................................................................Back €,.;ove,r
\
BEFORE OPERATING CHAIN SAW
I. Read and understand this owner's manual before operating chain saw.
2. Use chain saw for cutting wood only. Do not use for cutting any non-wood
items.
3. Only well-instructed adults should operate chain saw. Never allow children to
operate chain saw.
4. Use only electrical voltage noted on model plate of chain saw.
5. Use only extension cords marked for outdoor use. See page 12 for extension
cord requirements.
6. Do not operate chain saw.
• while under the influence of alcohol, medication, or drags
• in rain or in damp or wet areas
• where highly flammable liquids or gases are present
• if saw is damaged, adjusted wrong, or not fully assembled
• if trigger does not turn saw on and off. Chain must stop moving when you
release trigger. Have faulty switch replaced by authorized service center. See
page 29 for your nearest authorized service center.
• while tired or in a hurry
• while in treeior on a ladder unless trained to do so
_7017
A SAFETY
WARNINGS
Make certain you read
and understand all
Safety Warnings on
pages 2 through 5.
Improper use of this
chain saw can cause
severe injury or death
from fire, electrical
shock, body contact
with moving chain, or
failing wood.
_7017
7. Wear snug-fitting clothes when operating chain saw. Do not wear loose cloth-
ing orjewelry.Theycan get caughtin moving sawchain.
8. Wear the following safety gear when operating chain saw,
• heavy-duty gloves (wear robber gloves when working outdoors)
• steal-toed safety footwear with non-skid soles
• eye protection such as safety glasses, goggles, or face screen
• safety hard hat
• ear mufflers or ear plugs •
• hair covering to contain long hair
• face or dust mask (if working in dusty areas)-
Before cutting, always provide the following:
• clear work area
• securefooting
• planned retreat path from falling tree
I0. Inspect tree before cutting down. Make sure there are no dead limbs or
branches that may fall on you.
19.
KICKBACK
Avoid Kickback. Kickback can cause you to lose control of chain saw.
Kickback can cause severe injury or death.
Kickback Safety Devices On This Saw
This saw has a low-kickback chain and reduced kickback guide bar. Both items
reduce the chance of kickback. Kickback can still occur with this saw. Do not let ti
of guide bar touch anything when chain is moving.
Properly install front hand guard. This item can reduce injuries from kickback.
Follow assembly instructions on page 8. Do not remove front hand guard. Do not
replace front hand guard with substitute.
Cause Of Kickback
Kickback may occur when nose ortip of guide bar touches an object while chain is
moving. If chain cuttercatches on object, a sudden reverse action will result. The
guide bar will kick up and back towards operator.
Kickback may also occur when wood pinches chain at guide bar nose. A sudden
reverse action will also result.
The following steps will reduce the risk of kickback.
• Use both hands to grip saw while saw is running. Use firm grip. Thumbs and
fingers must wrap around saw handles.
• Keep all safety items in place on saw. Make sure they work properly.
• Do not overreach or cut above shoulder height.
• • Keep solid footing and balance
• Stand slightly to left side of saw. This keeps your body from being in direct line
with chain.
Contbtued
SAFETY
WARNINGS
Make certain you read
and understand all
Safety Warnings on
pages 2 through 5.
Improper use of this
chain saw can cause
severe injury or death
from fire, electrical
shock, body contact
with moving chain, or
falling wood.
• Do not let guide bar nose touch anything when chain is moving (see Figure I).
Direction \ \ \\ \\\ \\
Do Not Let
Guide Bar
90 =
Quadrant
Figure 1 ~ Kickback Hazard Example.
Do Not Let Nose of Guide Bar Touch Object While Chain is Moving
II
• Never try cutting through two logs at same time. Only cut one log at a time.
• Do not bury"guide bar nose or try.plunge cut (boring into wood using guide bar
nose).
• Watch for shifting of wood or other forces that may pinch chain.
• Use extreme caution when re-entering a previous cut.
• Use low-kickback chain and guide bar supplied with this chain saw. Only
replace these parts with chains and guide bars listed in this manual.
• Never use dull or loose chain. Keep chain sharp with proper tension.
• Do not hand sharpen chain on automatic chain sharpening (Fast Sharp) models.
Saw Maintenance and Kickback Safety
Follow maintenance instructions in this manual. Proper cleaning of saw and chain
and guide bar maintenance can reduce chances of kickback. Inspect and maintain
saw after each use. This will increase the service life of your saw. Note: Even with
proper sharpening, risk of kicklSack can increase with each sharpening.
PUSHBACK AND PULL-IN
Avoid pushback and pull-in. These hazards can cause you to lose
control of chain saw. Pushback or pull-in can cause severe injury.
Cause Of Pushback and Pull-In
Pushback may occur while cutting with top of guide bar. Pushback will force saw
back towards you. Pull-in may occur while cutting with bottom of guide bar. Pull-in
will force saw in towards wood you are cutting. These hazards can occur if chain is
pinched, caught, or contacts a non-wood object.
The following steps will reduce the risk of pushback or pull-in.
• Use both hands to grip saw while saw is running. Use firm gTip. Thumbs and
fingers must wrap around saw handles.
• Do not overreach or cut above shoulder height.
• Keep solid footing and balance.
• Stand slightly to left side of saw. This keeps your body from being in direct line
with chain.
• Have saw running at full speed before starting a cut.
• When cutting, make sure spike of saw is against wood (pull-in only). See
Product Identification, page 6, to locate spike.
• Never try cutting through two logs at same time. Only cut one log at a time.
• Watch for shifting of log or other forces that may pinch chain.
• Use extreme caution when re-entering a previous cut.
• Do not twist saw when removing guide bar from undercut.
• Use wedges made of plastic, wood, orlight alloy (never steel or iron) to hold cut open.
_70f7
SAFETY
JLLWARNINGS
_ake certain you read
and understand all
Safety Warnings on
pages 2 through 5.
Improper use of this
chain saw can cause
severe injury or death
from fire, electrical
shock, body contact
with moving chain, or
falling wood.
O97017
CHAIN SAW OPERATION
L Stay alert. Use common sense while operating chain saw.
-. Keep work area clean. Cluttered areas invite injuries.
3. Be aware of extension cord while operating chain saw. Be careful not to trip over
cord.
4. Keep children,animais,and bystandersaway from chainsaw and extension
cord.Only chainsaw usershouldbe inwork area.
5. Do notcutdown a treeunlessyou aretrainedor haveexperthelp.
6. Iftwo ormore personsperformbucking and fellingoperationsatthesame time,
provideplentyofdistancebetween operations.Providedistanceofatleast
twicetheheightoftreebeingfelled.
7. Securewood you arecuttingby usingdamps orchocks.
8. Grip chainsaw firmlywithbothhands.Never operatechainsaw with one hand.
Never usehandguard ashandle.
9. Keep fingerofftriggeruntilreadytomake cut.
I0.Beforestartingchainsaw,make surechainisnottouchinganything.
II.Avoid body contactwithgrounded objectssuch aspipes,fences,and metalposts.
12.Keep allpartsofbody away from chainwhen saw isrunning.
13..DonotforceChainsaw whilecutting.Apply lightpressure.
14.Cut smallbrushand saplingswithextremecare.Slendermaterialmay catchin
chainand be whipped towardyou.Thiscouldalsopullyou offbalance.
15.When cuttinglimbortreetrunkthatisunder tension,useextremecaution.Be
alertforwood springingback.When wood tensionisreleased,limbcould
spring back and strike operator causing severe injury or death.
16. Carry chain saw from one place to another
• with chain saw unplugged
• by holding front handle (never use hand guard as handle)
• with finger off trigger
• with guide bar and chain to rear
MAINTENANCE AND STORAGE OF CHAIN SAW
I. Unplug chain saw from power source
• when not in use
• before moving from one place to another
• before servicing
• before changing accessories or attachments
2. Inspect chain saw before and after each use. Check saw closely if guard or
other part has been damaged. Check for any damage that may affect operator
safety or operation of saw. Check for alignment or binding of moving parts.
Check for broken or damaged parts. Do not use chain saw if damage affects
) safety or operation. Have damage repaired by authorized service center.
i
I 3. Maintain chain saw with care.
I • Never expose saw to rain.
• Keep chain sharp, clean, and lubricated.
• Follow steps outlined in this manual to sharpen chain.
• Keep handles dry, clean, and free of oil.
• Keep all screws and nuts tight.
• Inspect power cord often. If damaged, have repaired by authorized service center.
• Never carry chain saw by power cord.
• Never yank power cord to unplug it.
• Keep power cord from heat, oil, and sharp edges.
4 • Inspect extension cords often and replace if damaged.
When servicing, use only identical replacement parts.
i Always store chain saw
• in a high or locked place, out of children's reach
/
• in a dry place |
• in a carrying case or with scabbard over guide bar
Keep this manual for reference. It is your guide to safe and proper operation of
this chain saw.
PRODUCT
IDENTIFICATION
Rear
Handle
Power Cord
Guard
Guide Bar
Nose
Saw
Chain
Rear Hand
Guard
o
Scabbard
Oil Level Sight Hole
(located on saw body,
hidden by front handle)
Front Handle'
!1
Motor
Housing
Switch Trigger
Lockout
Figure 2 - Electric Chain Saw
.z
J
0970
_7Of7
CHAIN SAW
NAMES and
TERMS
Bucking Process of cutting a felled tree or log into lengths.
Felling Processof cutting down a tree.
Feliin_g:CutFinal cutwhen fellinga tree.Makethis cut onoppositeside of tree
from notching cut.
Front Handle Located at front of saw body.
Front'Hand Guard Shield between front handle and guide bar. Protects left hand
while using saw.
Guide Bar Metal bar that extends from saw body. The guide bar supports and
guides chain.
Guide Bar Nose Tip oread of guide bar.
Kickback Quick backward and upward motion of guide bar. Kickback may occur
when tip of guide bar touches an object while chain is moving. The guide bar will
kick up and back towards operator.
2
Limbing p_ocess of cutting limb(s) from a felled tree.
Low-Kickback Chain Chain that reduces chance of kickback as required by ANSI
B175.1.
Normal Cutting Position Stance used while making bucking and felling cuts.
Notching Cut Notch cut in tree that directs fall of tree.
Oiler Control System for oiling guide bar ai_dchain.
Power Head Chain saw without chain and guide bar. Also known as saw body.
Pushback (Kickback, Pinch) Rapid pushback of chain saw. Pushbackmay occur
if chain along top of guide bar is pinched, caught, or contacts a foreign object.
RearHandle"Handlelocated at rear of saw body.
Reduced Kickback Guide Bar Guide bar that reduceschance of kickback.
Replacement Chain Chain that complies with ANSI B 175.1 when used with a
specific saw. It may not meet ANSI requirements when used with other saws.
Saw Chain (Chain) Loop of chain having cutting teeth for cutting wood. The motor
/ drives chain. The guide bar supports chain.
Spiked Bumper (Spike) Pointed teeth at front of saw body beside guide bar. Keep
spiked bumper in contact with wood when felling or bucking. It helps maintain
)osition of saw while cutting.
Sprocket Toothed wheel that drives chain.
Switch Device that completes or interrupts electrical circuit to motor of saw.
Switch Linkage This device connectsswitch to trgger. It moves switch when you
squeeze trigger.
Switch Lockout Device that reduces accidental starting of saw.
Trigger Device that turns saw on and off. Squeezing trigger turns saw on.
Releasing trigger turns saw off. : '
Trimming (Pruning) Process of cutting limb(s) from a living tree.
Undercut An upward cut from underside of log or limb. This is done while in
normal cutting position and cutting with top of guide bar. I_
UNPACKING
ASSEMBLY
1. Remove all items from carton.
2. Check all items for any shipping damage. If you find any damage or if any parts
are missing, promptly inform dealer where you bought chain saw.
. J
Note: Some models a_mpm assembled. Assembly is not needed on these models.
See Saw Ct_in Tension Adjusunent, page 10.
WARNING I
I
Cutting edges on chain are sharp. Use protective gloves when
handling chain.
IMPORTANT
Do not clamp chain saw in vise during assembly.
The plastic I_ardware bag should include:
• two guide bar bolts
• two guide bar nuts
• one Phillips-head tapping screw
• automatic chain sharpener (Fast Sharp models only)
1. Lay chain out fiat.
2. Install front hand guard onto saw body. Dothis by pressing two mounting
stand-outs on hand guard into hex-shaped holes in saw body (see Figure 3).
3 Insert tapping screw through hand guard and into saw handle. Tighten screw
firmly.
4. Turn adjusting screw counterclockwise (see Figure 4). Continue to turn adjust-
ing screw until adjusting block is to rear of adjusting plate.
5. Install guide bar onto saw body. Place rear of guide bar between adjusting plate
and sprocket support. IMPORTANT: Make sure to insert adjusting block into
oval adjusting hole on guide bar.
6. Line up holes on sprocket support with center slot on geide bar and holes in saw
body.
7. Insert guide bar bolts through front hand guard, saw body, center slot of guide
bar, and sprocket support. Attach guide bar nuts to guide bar bolts.
IMPOFITANT: Tighten guide bar nuts finger tight only. Make sure adjusting
block is in ova! adjusting hole on guide bar.
8. Place chain around drive sprocket, then along top groove of guide bar and
around guide bar nose. Note: Make sure cutting edges of chain are facing the
right direction. Position chain so cutting edges on top of guide bar face guide
bar nose (see Figure 3).
. CAUTION
Do not place chain on saw backwards. If chain is backwards, saw
will vibrate badly and will not cut.
9. Affjustsawchffmtandon.FollowstepsunderSawCJlainTensionAd]usLme-nf,
page 10.
ASSEMBLY
Continued
Tapping
Screw
i
•Front Hand
Towards
Guide
Bolts
Saw
Chain
Mounting _--_ -
Stand-Outs
Nuts
o
Figure 3 - Assembling Guide Bar, Chain, and Hand Guard
Adjusting
Plate
Adjusting
Screw
Sprocket
Support
° ,
t °
Figure 4 - Part Locations For Assembling Guide Bar
Contblued
Guide
Bar.
Adjusting
Hole
097017
ASSEMBLY
Continued
SAW CHAIN
TENSION
ADJUSTMENT
Installing Automatic Chain Sharpener
(Fast Sharp Models Only)
1. Screw automatic chain sharpener into threaded hole.
2. Continue turning automatic chain sharpener until you hear five (:_)clicks.
Automatic Chain
- Sharpener
Figure 5 - Automatic Chain Sharpener (Fast Sharp Models Only)
WARNING
Unplug chain saw from power source before adjusting saw chain
tension.
• 1=WARNING
Cutting edges on chain are sharp. Use protective gloves when
handling chain.
WARNING
Ma!ntai n proper chain tension always. A loose chain _Nill increase the
risk of kickback. A loose chain may jump out of guide bar groove.
This may injure operator and damage chain. A loose chain will cause
chain, guide bar, and sprocket to wear rapidly.
Note: For pre assembled models, the saw chain tension is properly set at factory. A
new chain will stretch. Check new chain after first few minutes of operation. Allow
chain to cool down. Follow steps below to readjust saw chain tension.
I. Before adjusting chain, make sure guide bar nuts are only finger tight (see Figure
3, page 9). Also make sure adjusting block is in oval adjusting hole on guide bar
(see Figure 3 and 4, page 9).
2. "rum adjusting screw clockwise until ,'ill slack is out of chain (see Figure 6).
Note: There should be n o gap between side links of chain and bottom of guide
bar (see Figure 7).
3. Wearing protective gloves, move chain around guide bar. Chain should move
freely. If chain does not move freely, loosen chain by turning adjusting screw
counterclockwise.
4. After chain tension is correct, tighten guide bar nuts firmly. If not, guide bar will
move and loosen chain tension. This will increase the risk of kickback. This can
also damage saw. Note: A new chain will stretch. Check new chain after first
few minutes of operation. Allow chain to cool down. Readjust chain tension.
m " t71_f7
SAW CHAIN
TENSION
ADJUSTMENT
Continued
FILLING
OIL TANK
O97O17
Figure 6- Turning Adjusting Screw
Correct Tension
Incorrect Tension
Figure 7 - Saw Chain Adjustment
1. Remove oil cap.
2. Fill oil tankwith SAE #30 motor oil. Note:For temperaturesbelow 30°F, use
SAE #10 oil. For temperatures above 75°1, use SAE #40 oil.
3. Replace oil cap at once. Tighten oil cap firmly for good seal. This will avoid oil
seepagefrom tank. _,
4. Wipe off excess oil.
Note:It is normal for oil to seep when saw is not in use. Empty oil tank aftereach
use to prevent seepage. _q
OPERATING
CHAIN SAW
WARNING
Read and understand this owner's manual before operating this
saw. Make certain you read and understand all Safety Warnings.
• Improper use of this chain saw can cause severe injury or death
from fire, electrical shock, or body contact with moving chain, or
falling wood.
EXTENSION CORDS
Use properextension cords with this saw. Use only extension cords marked for
outdoor use. The cord must be marked with suffix W-A following the cordtype
designation. Example: SJTW-A.
Use proper sized cord with this saw. Cord must be heavy enough to carry current
needed. An undersized cord will cause voltage drop at saw. Saw will lose power and
overheat. Follow cord size requirements listed below.
Cord Length AWG Cord Size
25 feet 16
_50feet 16
100 feet 14
150 feet 12
Keep cord away from cuttiiag area. Make sure cord does not catch on branches or
logs during cutting. Inspect cords often. Replace damaged cords.
The extension cord may come undone from the power cord during use. To avoid
this, make a knot with the two cords as shown in Figure 8 below.
Extension _ _ Chain Saw
cor,
Figure 8 - Tying Extension Cord and Power Cord in Knot
OILING CHAIN
Always check oil level before using saw. To oil chain, press oil cap. Oil will feed
onto gnide bar and chain. Press oil cap at least once before each cut. Check oil level
often by looking at oil sight level hole. Oil sight level hole is on left side of saw.
between front handle and front hand guard.
Figure 9 - Pressing Oil Cap to Oil Chain
097017
OPERATING
CHAIN SAW
Continued
CUTTING WITH THE CHAIN SAW
1. Connect saw to extension cord. Connect extension cord to power supply.
2. Make suresectionoflogtobe cutisnotlayingon _ound. Thiswillkeepchain
from touchinggroundasitcutsthroughlog.Touching groundwithmoving
chainwilldullchain.
3. Use bothhandstogripsaw.Always use lefthand to==,ripfronthandleandright
hand togriprearhanclle.Use firmgrip.Thumbs and fingersmustwrap around
saw handles(seeFigure10).
4. Make sureyourfootingisfirm.Keep feetapart.Divideyourweightevenlyon
bothfeet.
5. When readytomake a cut,pressinswitchlockoutwithrightthumb and squeeze
trigger(seeFigure10).This willtam saw on.Releasingtriggerwillturnsaw off.
Make suresaw isrunningatfullspeedbeforestartingacut.
Trigger
•Figure 10 - Switch Lockout and Trigger Location
6. When startinga cut,placemoving chainagainstwood. Hold saw firmlyinplace
toavoidpossiblebouncingorskating(sidewaysmovement) ofsaw."
Guide saw usinglightpressure.Do notforcesaw.The motor willoverloadand
can bum out.
8. Remove saw from a cut with saw running at full speed. Stop saw by releasing
trigger. Make sure chain has stopped before setting saw down.
9. Practice until you can maintain a steady, even cutting rate.
Continued
097017
B
m
OPERATING
CHAIN SAW
Continued
TRIMMING A TREE (Pruning)
WARNING
Avoid kickback. Kickback can result in severe injui'y or death. See.
Kickback, page 3 to avoid risk of kickback.
WARNING
Do not operate chain saw while
° in a tree
• on a ladder or any other unstable surface
• in any awkward position
You may lose control of saw causing severe injury.
WARNING
Do not cut limbs higher than your shoulders.
)
CAUTION
Seek professional help if facing conditions beyond your ability.
Trimming a tree is the process of cutting limbs from a living tree. Make sure your
footing is firm. Keep feet apart. Divide your weight evenly on both feet. Follow
directions below to trim a tree.
I. Make first cut six inches from tree trunk on underside of limb. Use top of guide
bar to make this cut. Cut 1/3 through diameter of limb (see Figure 11).
2. Move two to four inches farther out on limb. Make second cut from above limb.
Continue cut unti! you cut limb off.
'3. Make third cut as close to tree trunk as possible on underside of limb stub. Use
top of guide bar to make this cut. Cut I/3 through diameter of stub.
4. Make fourth cut directly above third cut. Cut down to meet third cut. This will
remove limb stub.
2nd Cut - Pruning Cut
. L_jJI / 4th Cut- Final (to avoid pinching)
_ ------2" to 4 )
/
1st Cut - Pruning Undercut
(to avoid splintering)
3rd Cut - Stub Undercut
(to avoid splintering)
Figure 11 - Cutting A Limb
t
€_,'ui7
09;'017
OPERATING
CHAIN SAW
Continued
?
FELLING A TREE (Cutting Down a Tree)
• WARNING
• Avoid kickback. Kickback can result in severe injury or death.
See Kickback, page 3 to avoid risk of kickback.
• Do not fell a tree without ample skill or expert help.
• Keep children, animals, and bystanders away from area when
felling a tree•
• If two or more persons perform bucking and felling operations
at the same time, provide ample distance between operations.
Provide distance of at least twice the height of tree being felled.
WARNING
When felling a tree, be aware of your surroundings. Do not
endanger any person, strike utility lines, or cause property dam-
age. If tree strikes utility lines, contact utility company at once.
Felling is the process of cutting down a tree. Make sure your footing is firm. Keep
feet apart. Divide your weight evenly on both feet. Follow directions below to fell a
tree.
, Before Felling a Tree
I. Before felling, inspect tree. Make sure there are no dead limbs or branches that
may fall on you. Study natural lean of tree. location of larger branches, and
wind direction. This will help you judge which way tree will fall.
2. Clear work area around tree.
3. Plan and clear a retreat path before felling. Make retreat path opposite to
• planned d.irection of fall of tree and at 45 ° angle (see Figure 12).
Retreat
Path
Direction ofFall
Retreat
Path
Figure 12 - Retreat Path From Tree
4. Remove dirt, stones, loose bark, nails, staples, and wire from tree where you
will make felling cuts.
5. Stay on uphill side when felling tree. Tree could roll or slide downhill after
falling.
Felling Procedure
Felling Notch
A properly placed felling notch will determine direction tree will fall. Place felling
notch on side of tree in direction you want tree to fall (see Figure 13, page 16).
Follow directions on page 16 to create a felling notch roll
OPERATING 1
CHAIN SAW I
Continued ! 2.
!
• 3.
i, i,
Make lower notch cut as close to ground as possible. Hold saw so gui_de bar is
horizontal. Cut 1i3 the diameter of tree trunk'(see Figure 13). Note: Always
make this horizontal lower notch cut first. If you make this cut second, tree can
pinch chain or guide bar.
Start upper notch cut the same distance above first cut as first cut is deep.
Example: If lower notch cut is eight inches deep, start upper notch cut eight
inches above it. Cut downward at 45 ° angle. The upper notch cut should meet
end of lower notch cut (see Figure 13).
Remove tr_ trunk wedge created by notching cuts.
Felling Cut
I. Make felling cut two inches higher than lower notch cut and on opposite side of
tree (see Figure 13). Keep felling cut parallel to lower notch cut.
2. Cut towards notch.
WARNING
Do not cut all the way through tree. Leave about two inches of tree
diameter uncut directly behind felling riotch (see Figure 13). This
uncut portion acts as a hinge. The hinge helps keep tree from
twisting and falling in wrong direction.
.Direction of Fall
3rd Cut - Felling Cut Hinge I!1_ dtc_
12 inches _,_ i _. //_ UcutUpper
2inches J" "__:___.. ----1NSttcChUtc-LOwer
Figure 13 - Felling A Tree
3. As felling cut nears hinge, tree should begin to fa!l. Note: If needed, drive
wedges into felling cut to control direction of fall. If tree settles back and
pinches chain, drive wedges into felling cut to remove saw. Only use wedges
made of wood, plastic, or aluminum. Never use wedge made of steel• This couk
cause kickback and damage to chain.
4. When tree begins to fall, quickly
• remove saw from felling cut
• release trigger to rare saw off
• put saw down
• exit area using retreatpath
WARNING
Be alert for failing overhead limbs. Watch your footing while
exiting area.
¢.q#/u t
OPERATING
CHAIN SAW
Continued
LIMBING A TREE
WARNING
Avoid kickback. Kickback can result in severe Injury or death. See
Kickback, page 3 to avoid risk of kickback.
WARNING
When cutting limb that is under tension, use extreme caution. Be
alert for wood springing back. When wood tenston is released,
limb could spring back and strike operator causing severe injury
or death.
Limbing is removing branches from a fallen tree. Make sure your footing is firm.
Keep feet apart. Divide your weight evenly on both feet. Do not remove larger limb
under tree that support log offground. Remove each limb with one cut (see Figure
14). Clear cut limbs from work area often. This will help maintain a safe work area.
Make sure you start your cut where limb will not pinch saw during cutting. To avoid
pinching, start cut on freely hanging limbs from above limb. Start cut on limbs
under tension from under limb. If pinch occurs, turn saw off, lift limb, and remove
saw.
Figure 14 - Limbing A Tree
Continued
097077
OPERATING
CHAIN SAW
, +Continued
BUCKING A LOG
• WARNING
Avoid kickback. Kickback can result in severe+injury or death. See
Kickback, page 3 to avoid risk of kickback.
I
WARNING
• If onslope, make:sure log will not roll down hill. Secure log by
using wooden stakes. Drive wooden stakes into ground on
downhill side of log. Stand on uphill side of log while cutting. Log
may roll after cutting.
• Never try cutting through two logs at same time. This could
increase the risk of kickback.
• While cutting log, never hold log With your hand , leg, or foot.
While cutting log, neVer allow another person to hold log.
Turn off and unplug saw before moving from one place to another.
Bucking a log is cutting a log into sections. Make sure your footing is firm. Keep
feet apart. Divide your weight evenly on both feet. When possible, raise log or
section off ground. Do this by using limbs, logs, chocks, etc.
When cutting through log, maintain control by reducing cutting pressure near end of
: cut. Do not relax your grip on chain saw handles. Do not let moving chain touch
ground. Ground will dull moving chain. After Cutting through log, release trigger to
turn saw off before moving saw.
Follow directions below to buck a log.
Entire Length Of Log On Ground"
I. Cut log from top (see Figure 15).
Figure 15 - Bucking Log With Entire Length On Ground
m
097017
OPERATING
CHAIN SAW
Continued
Log Supported On One End
1. Make first cut on underside of log (see Figure 16). Use top of guide bar to make
this cut. Cut I/3 through diameter of log. This cut will keep section from
splintering when cut.
2. Make second cut directly above first cut. Cut down to meet first cut. This cut
will keep log from pinching guide bar and chain.
2nd Cut
\
1st Cut
Figure 16.- Bucking Log When Log Is Supported On One End
Log Supported On Both Ends
1. Make first cut from above log (see Figure 17). Cut 1/3 through diameter of log.
This cut will keep section from splintering when cut.
2. Make second cut on underside of Iog,directly under first cut. Use top of guide
bar to make this cut. Cut up m meet first cut. This will keep log from pinching
guide bar and chain.
I.
+stcut
2nd Cut
Figure 17- Bucking Log When Log Is Supported On Both Ends
m
097017
CLEANINGI AND
MAINTENANCE
NOTICE t
Below are instructions for servicing your chain saw. Any servicing not
mentioned below should be done by an authorized service center.
CLEANING SAW BODY.
A WARNING
Unplug chain saw from power source before servicing. Severe
injury or death could occur from electrical shock or body contact
with moving chain.
• ILWARNING
Cutting edges on chain are sharp. Use protective gloves when
-handling chain.
WARNING
When cleaning saw body,
• do not submerge saw in any liquids
• do not use products that contain ammonia, chlorine, or
abrasives
• do not use chlorinated cleaning solvents, carbon tetrachloride,
kerosene, or gasoline
Keepsaw body clean. Use a soft cloth dampened with a mild soap and water
mixture. Wipe saw body to clean.
CARE OF GUIDE BAR
Uneven bar wear causes most guide bar problems. Incorrect sharpening of chain
cutter and depth gauge settings often cause this. When bar wears unevenly, it widens
guide bar groove (see Figure 18):This causes chain clatter and rivet popping. Saw
will not cut st_ight. Replace guide bar if this occurs.
Inspect guide bar before sharpening chain. A worn or damaged guide bar is unsafe.
A worn or damaged guide bar will damage chain. It will also make cutting harder.
_//_ Guide Bar
Groove
Normal Guide Bar
Guide Bar
Groove
•Guide Bar
Guide Bar With
Uneven Wear
Figure 18 - Guide Bar Cross Section Showing Uneven Bar Wear
097017
CLEANING AND
MA' a T E acAnNnCu E
Normal Guide Bar Maintenance
1. Remove guide bar from chain saw.
2. Remove sawdust from guide bar groove periodically. Use putty knife or wire.
3. Clean oil slots after each day of use.
4. Remove burrs from sides of guide bar. Use flat file to make side edges square.
Burr
Flat File
Cleaning Groove _ __ /
WRh PuttyKnife
Oil Slot
Figure 19 - Guide Bar Maintenance
Guide
Bar
Replace guide bar when
• bar is bent or cracked
• inside groove of bar is badly worn
Note: When replacing guide bar, see Replacement Parts and Accessories, page 28
for pmper bar.
SHARPENING'YOUR SAWCHAIN
(Non-Fast Sharp Model)
WARNING
Unplug chain saw from power source before servicing. Severe
injury or death could occur from electrical shock or body contact
with moving chain.
WARNING
Cutting edges on chain are sharp. Use protective gloves when
handling chain.
O97O17
Keep chain sharp. Your saw will cut faster and more safely. A dull chain will cause
undue sprocket, guide bar, chain, and motor wear. If you must force chain into wood
and cutting creates onJy sawdust with few large chips, chain is dull.
Items Needed to Sharpen Chain
Purchase theseitems from your local dealer, hardware store, or chain saw supplies
outlet.
5/32" round file • Depth gauge tool
File guide • Vise
• Medium sized fiat file Continued
CLEANING AND
VlAINTENANCE
Contmued
Sharpening Cutters.
Use file guide for 30° filing.
1. Adjust chain for propertension (see Saw Chain Tension Adjustment, page 10).
12. Clamp guide bar in vise to hold saw steady. Note: Do not clamp chain.
3. Press 5/32" round file (attached to file guide) into Voove between top plate and
depth gauge on chain_ File guide should rest on both top plate and depth gauge
(see Figures 20 and 21). Note: File at midpoint of guide bar.
4. Hold file guide level. Make sure 30* mark on file guide is parallel to center of
guide bar (see Figure 20). This will insure that you file cutters at 30*angle.
5. File from inside towards outside of cutter until sharp.Only filein this one direction
(see Figure 20). Note: Two or three strokes with file should sharpencutter.
6. After each cutter if sharpened, move chain forward to sharpen next cutter.File
all cutters on one side of chain.
7. Move to'other side of chain and repeat process.
_. _ Filing
Direction
30° Guide
\
\
•5/32"
Round File
Note: This
illustrationshows
file guide pEace-
ment and filing
directionfor
sharpeningcutters
on left side of
chain.
Figure 20 - File and File Guide Placement On Chain
Depth Gauge
(left side ofchain)
of Chain
/
Gauge
(rightside ofchain
Top Plate
(left side of
Right Side
of Chain
Top Plate
(rightside ofchain)
m - Figure 21 - Chain Part Locations
CLEANING AND
MAINTENANCE
Continued
Filing Cutter Depth Gauges
The cutter depth gauge clearance is reduced as cutters are sharpened. After every
second or third sharpening, reset cutter depth gauges.
1. Place depth gauge tool firmly across top of two cutters. Make sure depth gauge
enters slot in depth gauge tool (see Figure 22).
2. Use medium flat file. File depth gauge level with depth gauge tool.
3. Remove depth gauge tool. With fiat file, round off front comer of cutter depth
gauge (see Figure 23).
Flat File Depth Gauge
Depth Gauge Tool
Depth Gauge
Slot
Figure 22 - Depth Gauge Tool On Chain
Front Comer
Figure 23 - Round Off Front Comer Of Depth Gauge
_-After several hand filings, have authodzed service center or sharpening service
i machine sharpen chain. This will insure even filing.
I
Replacing Saw Chain
Replace chain when cuttersare too worn to sharpen or when chain breaks. Only use
replacement chain noted in this manual. Always include new drive sprocketwhen
replacing chain. "this will maintain proper ddving of chain. Note: For proper chain
and drive sprocket, see Replacement Parrs and Accessories, page 28.
Ittl
097017
CLEANING AND
MAINTENANCE
Continued
SHARPENING YOUR SAW CHAIN
(Fast Sharp Model)
,0 WARNING
Unplug chain saw from power source before servicing. Severe
injury or death could occur from electrical shock or body contact
with moving chain.
A WARNING
Cutting edges on chain are sharp. Use protective gloves when
handling chain.
WARNING
Do not hand-sharpen this Fast Sharp chain. Hand-sharpening
chain will increase risk of kickback.
Keep chain sharp. Your saw will cut faster and more safely. A dull chain will cause
undue sprocket, guide bar, chain, and motor wear. If you must force chain into wood
and cutting creates only sawdust with few large chips, chain is dull.
FoUow the steps below to sharpen Fast Sharp chain. The automatic chain sharpener
sharpens cutter, lowers cutter depth gauge, and adjusts guard drive link.
I. Adjust saw chain for propor tension (see Saw Chain Tension Adjustment,
page I0).
2. Clean out excess sawdust and wood chips from drive sprocket area.
3. "rum sharpener knob counterclockwise until clicking stops.
4. "rum sharpener knob clockwise until you hear five distinct clicks.
. Figure 24 - Turning Sharpener Knob
5. Place saw on clean, fiat smface.
6. Connect saw to power supply.
7. Hold saw, with both hands in normal cutting position.
8. Press in switch lockout with right thumb and squeeze trigger.
CLEANING AND
MAINTENANCE
Continued
9. Gently push on sharpener knob. Saw must be running for chain m sharpen.
Note: Sparks appearing shows sharpener is working (see Figure 25). If no sparks
appear, continue to adjust sharpener one click at a time. After each click, press
sharpener knob until light flow of sparks appears.
\
STORAGE
Figure 25 - Sharpening Fast Sharp Chain
After several sharpenings, you must turn sharpener knob more to bring stone into
position•
Replacing Saw Chain
Replace chain whencutters are too worn to sharpen or when chain breaks. Only use
replacement chain noted in this manual. Always include new drive sprocket when
replacing chain. This will maintain proper driving of chain. Note: For proper chain
and drive sprocket, see Replacement Parts and Accessories, page 28.
If storing saw for more than 30 days, follow steps below.
1. Drain oil tank.
2. Remove and clean guide bar and chain. Clean guide bar and chain by soaking in
petroleum based solvent or mild soup and water mixture.
3. Dry guide ba[ and chain:
4. Place chain in container filled with oil. This will prevent rust.
5. Wipe a thin coating of oil over surface of guide bar.
6. Wipe off outside of saw body. Do this with soft cloth dampened with a mild
soap and water mixture.
7. Store chain saw
• in a high or locked place, out of children's reach
• in a dry place
• in a ca'Tying case or with scabbard over guide bar
TROUBLE-
SHOOTING
,/k WARNING
Unplug chain saw from power source before servicing. Severe
injury ordeath could occur from electrical shock or body contact
with moving chain.
OBSERVED POSSIBLE
FAULT CAUSE REMEDY
Saw runs, but does Chain asserabled backwards See Assembly, page 8
_otcut. on guide bar
Saw does not cut Chain is dull See Sharpening your
unless heavily Saw Chain, page 2 I
forced. Cutting (non-Fast Sharp model) or
produces only page 24 (Fast Sharp
sawdust with few model)
large chips.
2
Saw runs Slow. Low power supply voltage Extension cord wire size too
Saw stalls easily, small. See ExterLfion
Cords, page 12
Motor of saw does Switch lockout not pressed in Press in switch lockout
not runwhenyou m releasetrigger beforesqueezing trigger
squeeze_gger. Extension cordconnections
loose
Open line fuse or circuit
breaker
Bad motor brushes
Open wiring circuit on saw
Check cord connections
Check line fuse or circuit
breaker
See authorizedservice center
(see page 29)
See authorizedservice center
(see page29)
Motor of sawruns,
butchaindoesnot
move.
Gear train failure See authorized service center
(see page 29)
Chain does not get
oil.
Clogged oil slot in guide bar
Oil is too thick
Remove guide bar and clean
oil slot
Use correct weight of oil.
See Filling Oil Tank,
page 11
Chain comes off Chain is loose Tighten chain. See Saw
guide bar. Chain Ter_ion
Adju_tmem, page 10
Guide bar and chain not Se_ Assembly, page g
assembled right
Saw smokes. Saw damaged. Do not use saw. See authorized service center
(see page 29)
Saw leaks oil. Oil cap is not secure. Tighten oil cap.
Note: Empty oil tank
when not in use.
TECHNICAL
SERVICE
SERVICE
PUBLICATIONS
REPAIR
SERVICE
You may have furtherquestions about assembling, operating, or maintaining this
saw. If so, contactDESA International's Technical Service Depa_mnentat 1-800-
323-5190.
You canb.uya servicemanual from addresslistedon back page ofthismanual.
Send a checkfor$5.00payabletoDESA International.
You can receive an illustrated parts list free of charge.'Send a self-addressed
stamped envelope to address on back page of this manual.
When writing, include model number and serial number of saw. You will find these
numberson sawmotorhousingdecal.
Note:Onlyuse original replacement parts. This will protect your warrantycoverage
for parts replaced under warranty.
Eachauthorizedservice centeris independently owned and operated.For additional
servicecenterorwarranty information, call 1-800-323-5190.
Warranty Service
If saw requires warrantyservice, mmrn it to nearest authorized service center. You
must show proof of purchase. If faulty materials or workmanship caused damage,
we will repairor replace saw without charge.
i Non-Warranty Service
If sawrequires.service,returnit to nearestauthorized servicecenter.Repairswill be
billed to you at regularrepair list prices. Note: Normal wear, misuse, abuse, neglect,
or accidental daTa.age is not covered under warranty.
m
09"/017
REPLACEMENT
PARTS AND
ACCESSORIES
WARNING
Use only replacement parts and accessories described in this
manual. Use of oth .er parts or accessories could damage saw or
injure operator.
Purchase these parts and accessories from your local dealer. If they can not supply
these parts and accessories, either contact your nearest Pacts Central (se_ page 29)
or call DESA International's Parts Department at 1-800-972-7879. You can also
write to the address listed on the back page of this manual.
.NT-2
_art Number Description
097566-01S Guide bar, 8"
091369S Chain, 8Y
097567-02S Guide bar, 10"
:091371S Chain, 10"
097568-02S Guide bar, 12"
091373S Chain, 12"
075752 Drive sprocket
099178H, 100089-06 & EL-1 "
Part Number Descriptio_t
097570-03S Guide bar, 14"
091374S Chain, 14"
075752 Drive sprocket
EL-1 Fast Sharp
Part Number Description
097570-03S Guide bar, 14"
091367S* "Chain, 14"
076695 Drive sprocket
EL'7, 098031J, 099039J,
100089-01, 100089-04
=art Number Description
097572-03S Guide bar, 16"
091375S Chain,16"
075752 Drive sprocket
EL-7 - 100015
Part Number Description
101623-01 Guide bar, 15"
101619-01 Chain, 15"
075752 Drive sprocket
EL-7 Fast Sharp
Part Number Description
097572-03S Guide bar, 16"
091377S* Chain, 16"
076695 Drive sprocket
General
Part Number
079963-02
079963-04
059397
Description
Plastic scabbard,
8" & 10"
Plastic scabbard,
12", 14", & 16"
Extension cord,
two conductor
(16 AWG, 50 ft.)
* Includes automatic chain sharpener.
(_;'01Z
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when writing the factory.
We reserve the fight to amend these specifications at any time without notice. The only warranty applicable is our
standard written warranty. We make no other warranty, expressed or-implied.
•LIMITED WARRAI_ITY
ELECTRIC CHAIN S.AW
DESA International warrants this electric chain saw and any parts thereof, to be free from defects in material
and workmanship for one year from the date of first purchase from an authorized dealer, provided that the
product has been properly maintained and operated in accordance with all applicable instructions. The bill of
sales or proof of purchase must be presented at the time a claim is made under this warranty.
•This warranty is extended only to the original retail purchaser.This warranty covers only the parts and labor
required to restore this chain saw to its proper operating condition. Warranty parts must be obtained through
factory authorized dealers and service centers for this product. These dealers and service centers will provid e
original factory replacement parts. Failure to use original factory replacement parts voids this warranty.
This warranty does not cover commercial, industrial, or rental u._age, nor does it apply to parts that are not in"
original condition because of normal wear and tear, or parts that fail or become damaged as a result of
misuse, accident, lack of proper maintenance, tampering, or alteration. Travel, handling, transportation, and
incidental costs associated with warranty repairs are not reimbursable under this warranty and are the
responsibility of the owner.
To the full extent allowed by the law of the jurisdiction that governs the sale of the product, this express
warranty excludes any and all other expressed warranties and limits the duration of any and all implied
warranties, including warranties of merchantability and fitness for a particular purpose to one year form the
date of first purchase, and DESA International's liability is hereby limited to the purchase price of the
product and DESA International shall not be liable for any other damages whatsoever including indirect,
incidental, or consequential damages.
Some states do not allow limitation of how long an implied warrantylasts oran exclusion or limitation of
incidental or consequential damages, so the abov_limitation of damages may not apply to you.
This warranty provides the original purchaser with specific rights. For information regarding those fights,
please consult the applicable state laws.
DESA
INTERNATIONAL
2701 IndustrialDrive
P.O.Box90004
BowlingGreen, KY42102-9004
097017-01
REV.S //_
