Loading ...
2
INSTALLATION INSTRUCTIONS
1. (For U.K., Australian, and New Zealand use)
A cut-out will have to be provided in the side of the kitchen cabinet for the plug of the oven.
N.B.The mains plug must be accessible after installation or an all-pole switch disconnection must
be provided with a contact separation of at least 3 mm in each pole.
(For use in Continental Europe)
The electric outlet must be installed at 150 mm high from the oor of the built-in cabinet and
at 50 mm from the right wall of the built-in cabinet as shown in Fig. 1. The mains plug must be
accessible after installation or the oven must be connected to an electric circuit provided with
an all-pole switch (contact gap no less than 3 mm) to disconnect the oven in case of danger.
A safety-device like a fuse in the installation may be used as a switch.
2. Remove the built-in kit from the package.
3. Set the spacing brackets
1
on the shelf along the right and left walls of the kitchen cabinet,
adjusting the front ends of the shelf and the spacing brackets, and attach them with the four screws
E
,
as shown in Fig.1.
Caution: The arrow marks on each spacing bracket should be pointing towards you.
4. Place the exhaust duct
2
on the ceiling of the kitchen cabinet along the back wall of the cupboard
Ⓓ
and left wall of the kitchen cabinet without the clearance as shown in Fig.1 and 2. Secure to
the ceiling of the kitchen cabinet with two screws
E
from below as shown in Fig. 3.
5. Remove the backing paper from the cushion
6
. Attach the cushion
6
to the edge of the exhaust
duct
3
as shown in Fig. 4.
6. Insert two tabs of the exhaust duct
2
into the slits of the exhaust duct
3
. And fold the tabs.
7. Remove the screw
Ⓔ
from the oven as shown in Fig. 5.
8. Let the power supply cord pass through the hole of the lower side of the intake duct
4
as shown
in Fig. 6.
9. Install the intake duct
4
to the rear of the oven with two screws
R
and
Ⓔ
(removed at step 7) as
shown in Fig. 6.
Caution: Avoid pinching the power supply cord between the oven and the intake duct
4
.
10. Install the intake duct
5
to the rear of the oven with three screws
R
as shown in Fig. 7.
Caution: Avoid pinching the power supply cord between the oven and the intake duct
4
.
11. Remove the backing paper from the three cushions
7
,
8
and
9
. Attach the cushion
7
at the left
side along the intake duct
4
then attach the cushion
8
at the top of the intake duct
4
, and along
the left side of the cushion
7
and the oven as shown in Figs. 8-a and 8-b. Attach the cushion
9
to
the top of the oven as shown in Figs 8-a and 8-b.
12. (For U.K., Australian, and New Zealand use)
Place the oven on a table/stand positioned in front of the kitchen cabinet. If you do not prepare
the table/stand, two persons are required. One to hold the oven whilst the other feeds the power
supply cord through the prepared cut out.
(For use in Continental Europe)
Place the oven on a table/stand positioned in front of the kitchen cabinet.
If you do not prepare the table/stand, two persons are required. One to hold the oven whilst the
other connects it to the power supply.
13. Connect the oven to the power supply.
Caution: a. In U.K., Australia, and New Zealand, connect the oven to the power supply 230-240 V,
50 Hz.
b. In Continental Europe, connect the oven to the power supply 230 V, 50 Hz.
14. Make sure the oven is on the spacing brackets on the shelf of the kitchen cabinet. Then adjust the
position of the oven so that the feet of the oven are tted into the recesses of the spacing brackets
as shown in Fig. 2.
Caution: Make sure that the power supply cord does not touch the air vent openings behind
the oven.
15. Place the built-in frame element
Q
on top of the oven making sure that it is level both vertically
and horizontally. Secure loosely to the kitchen cabinet with two screws
T
as shown in Fig. 9.
16. Insert two built-in frame side elements
W
between the built-in frame element
Q
and the kitchen
cabinet. And secure two screws
T
tightly as shown in Fig. 9. Check location by measuring
distance between right and left built-in frame side elements
W
. The distance is stated in Fig. 10.
Note: Fit the hole of the built-in frame side element
W
to the screw
T
when inserting.
17. Install the second built-in frame element
Q
over the built-in frame side elements
W
at bottom edge
of the oven. And secure the built-in frame element
Q
through the holes of the built-in frame side
elements
W
to the kitchen cabinet with two screws
T
as shown in Fig. 9.
Caution: Make sure that 6.5 mm of the frames (upper and lower) and cabinet overlap each
other as shown in Fig. 11, or the kitchen cabinet door may touch the built-in frame
elements.
EBR-99ST.indd 2 2016/02/08 17:35:53