1
This is an replacement sheet for the instruction book attached.
Keep this sheet with the instruction book for future reference.
Instruction for SHARP Built-in Kits EBR-99ST/EBR-9900 (W)/(SL)/(BK)/EBR-9910(SL)
Before installing a Sharp Microwave Oven, read and check the following points.
SAFETY INFORMATION
1. Except U.K., for use in Continental Europe only.
The oven must be connected to an electric circuit provided with a switch (contact gap no
less than 3 mm) to disconnect the oven in case of danger. A safety-device like a fuse in the
installation may be used as a switch.
2. Disconnect the oven from the power supply before installation.
3. Surround
a. Make sure that the EBR-99ST/EBR-9900/EBR-9910 is the correct surround for your oven.
b. The Sharp Microwave Ovens are designed to either stand neatly on a kitchen counter top or
to be built into a tted kitchen cabinet using the surround.
c. The EBR-99ST/EBR-9900/EBR-9910 surround will become hot during oven operations when
using the heater elements. Take care to prevent burns when you use the oven.
4. Kitchen cabinet
Prepare the kitchen cabinet as follows;
a. The kitchen cabinet must be of the following dimensions as shown in Fig. 1.
WIDTH : 560 mm - 568 mm
HEIGHT : 468 mm
DEPTH : 550 mm - 580 mm
b. Make sure that the back wall of the cupboard
Ⓓ
is always tted to ensure the correct
ventilation of the oven and that the ventilation gap
Ⓒ
is 45 mm as shown in Figs 1 and 2.
c. The shelf of the kitchen cabinet should be made to withstand the weight of the microwave
oven to be installed and the heaviest item likely to be cooked in the microwave oven. Refer to
the operation manual for microwave oven weight.
5. Installation near to a conventional oven
a. When a microwave oven is to be installed next to a conventional oven, sufcient space
between them should be allowed to prevent overheating as the surround can warp with
excessively high temperatures. Obviously, it is important to adhere strictly to the conventional
oven manufacturer's installation instructions.
b. A built-in microwave oven must not be installed above a conventional oven otherwise the
microwave oven's cooling system may be adversely affected by hot air produced by the
conventional oven.
6. Installation near a refrigerator or freezer
a. If the microwave oven is to be installed above a refrigerator or freezer requiring back
ventilation, a ventilation duct behind the microwave oven must be provided. It is essential that
the refrigerator/freezer manufacturer's installation procedures are followed.
b. Do not install the microwave oven above a refrigerator or freezer which are ventilated at the front.
(For Australia and New Zealand)
Do not install the microwave oven above a refrigerator or freezer.
7. Fixing
To avoid any possibility of the kitchen cabinet moving when the microwave oven is installed, it is
essential that the kitchen cabinet is xed to the back wall.
8. Adjustment and repair
It is dangerous for your oven to be adjusted or repaired by anyone except properly qualied
service technicians trained by Sharp.
If the appliance is ever removed from the cabinet it should be re-installed in accordance with these
instructions, which should be kept in a safe place for future reference.
For Australia and New Zealand/Für Australien und Neuseeland/Pour l'Australie et la Nouvelle Zélande/
Voor Australië en Nieuw-Zeeland/Per l'Australia e la Nuova Zelanda/Para Australia y Nueva Zelanda
The manufacturer and/or the distributors of this product cannot be held liable for any damages to
the microwave oven and/or the built-in kit caused by improper installation or adjustment.
TINS-A872WRRZ-J61
EBR-99ST.indd 1 2016/02/08 17:35:53
Loading ...
