Loading ...
Loading ...
Loading ...
1744010, 1744011 V1 E
Don’t forget to register your lock at Truboltlocks.info for updates.
In order to program the lock, you
must create a new administrator code
Creating A New Administrator Code
Repeat the 6 digit code
Press to Confirm
Input Admin code
(default 123456)
Press
Contact Us First! Do Not Return to Store
EMAIL: [email protected]
WEBSITE: www.truboltlocks.info
ADDRESS: Consumer Assistance Dept.
Lewis Hyman, Inc.
860 East Sandhill Avenue
Carson, CA 90746 USA
TELEPHONE: US/Canada 800-860-1677 Ext. 1801 (Toll Free)
Troubleshooting
Issue Solution
Keypad will not
function.
• Check that all batteries are fresh high quality Alkaline Batteries
• Check for proper polarity (+ -) of all batteries
• Check that the Control Wire is attached to the Interior Assembly
The Latch is sticking.
Installation screws of the lock may be too tight and have to be loosened
• Remove Interior Assembly
• Slightly loosen the Mounting Plate screws
• Lock and unlock using the Key
• Reattach Control Wire and Interior Assembly
Voice says “Ready to
unlock” but thumb
knob will not turn.
Lock not installed correctly
• Ensure latch is kept horizontal when installing lock
• Install lock with bolt extended
No space to store
more users.
• Delete old user codes or fingerprints
Fingerprint is invalid.
• Make sure your fingers and the fingerprint reader are both clean
• Keep your finger on the reader still until you hear the beep
• Try using recording another fingerprint
Latch is not locking in
inclement weather.
• Push or pull door to direct latch
• Re-adjust latch for smoother operations
Admin Code Does not work. • Press numbers slowly and carefully
Fingerprint Does not work. • Hold fingerprint on reader pad longer
Locked out due to wrong
code entry
• Wait 60 seconds and then try again
Lock is frozen and will not
opperate
• Remove one battery for 30 second to refresh lock
Batteries are dead • Open the lock with Override Access Key and replace batteries
Customer Service
Input user I.D. (01-50)
Press
Press Press
1
1
Input your Admin code
Press
Input a 4-6 digit code
Press
Repeat the 4-6 digit code
Press
Set Up User Codes
“ ” Confirm
“ ” Wake up lock /
Go back to
previous menus
Function Buttons
NOTE: Set yourself up as user code 01. Follow prompts to select
your passcode. Follow prompts to add additional user codes.
NOTE: Admin Code must be 6 digits and can only be used
to access the settings, it cannot be used to unlock.
Additional Programming Functions
1. On (Default setting)
1. Input Administrator code
2. Press “4”
3. Press “1”
2. Off
1. Input Administrator code
2. Press “4”
3. Press “2”
Restore factory setting
1. Press any key to wake up the touchpad
2. Hold the “reset” button on the back panel (upper position of battery)
for at least 5 seconds.
Voice Guide
NOTE: Make sure you hear “SUCCESS” to insure that
the Reset occurs
To wake-up lock for Programming:
1. Swipe you fingers across the face to activate lock
2. Press the Illuminated Security Numbers
To add or remove User Codes
1. Input Administrator code
2. Press “ ” to confirm
3. Press “1”
4. Select from the list below
Manage User Passcode
“1” Add user code
“2” Delete user code
“3” Delete all users codes
“1” Add user codes
1. Input the user ID (a two or three digit number from 01 to 50)
2. Press “ ” to confirm
3. Input the desired user code (4-6 digits)
4. Press “ ” to confirm
5. Repeat the user code
6. Press “ ” to confirm
“2” :Delete user codes
1. Input the user ID that you want to delete
2. Press “ ” to confirm
“3” :Delete all user codes
1. Voice prompt notification that this will delete all existing user codes
2. Press “ ” to confirm
NOTE: If the User ID, or code already exists
there will be a related voice prompt.
Each user needs their own code assigned.
User Code Management
When programming you will be prompted to add another passcode
or press the “ ” to return to the previous menu when finished
Passcode Programming Functions
User Records
User Passcodes must be 4-6 digit codes
User 01 Passcode should be reserved for Owner
User Name/Code 01 - 50
User / Code User / Code
01
02
03
04
05
06
07
08
09
10
11
12
13
26
27
28
29
30
31
32
33
34
35
36
37
38
14
15
16
17
18
19
20
21
22
23
24
25
39
40
41
42
43
44
45
46
47
48
49
50
Fingerprint Programming Functions
4b
Input user I.D. (01-50)
Press
Press Press
2
1
Input your Admin code
Press
Record User Fingerprint
Repeat User Fingerprint
Set Up User Fingerprint
NOTE: Set yourself up as user fingerprint 02.
Follow prompts to add print to biometric reader.
Operating the Lock
Locking
The deadbolt can be locked at any time.
Turn Thumb turn knob to lock the door
Unlocking
User codes or Fingerprints can unlock the door
1. Enter user code or fingerprint until you hear a beep
2. Turn Thumb turn knob to open door
It is best to write down your new administrator code
prior to step 2. Code cannot be less than 6 digits:
Complete all the programming steps in the
programming mode within 10 seconds
Do not press keypad until keypad stops illuminating
Proceed to Step 2
Press
3
Input a 6 digit code
Press
11
2 3a 3b
4a 5
To add or remove User Fingerprints
1. Input Administrator code
2. Press “ ”
3. Press “2”
4. Select from list below
Manage User Finger Print
“1” Add user fingerprint
“2” Delete user fingerprint
“3” Delete all users fingerprints
“1” : Add user fingerprint
1. Input the user ID (a two or three digit number from 01 to 50)
2. Press “ ”
3. Record the user fingerprint
4. Repeat the user fingerprint
5. Repeat the user fingerprint
6. Success
NOTE: User fingerprints must have individual user codes
“2” :Delete user fingerprint
1. Input the user ID that you want to delete
2. Press “ ”
“3” :Delete all user fingerprints
1. Voice prompt notification that this will delete all existing fingerprints
2. Press “ ” to confirm
User Fingerprint Management
When programming you will be prompted to add another fingerprint
or press the “ ” to return to the previous menu when finished
Loading ...
Loading ...
Loading ...