Loading ...
Loading ...
Loading ...
Features
Cycle Signal Control (some models)
When the Cycle Signal Control is ON, a signal wi]l sound at the end of each
cycle and during the WRINKLE-RID setting (some models), The volume is
adjustable on some models_
L
t'e
Pace the front bar under
the lip of the tint screen opening,
Drum Light (some models)
A drum light will come on whenever the door is opened to illuminate the dryer
drum during loading and unloading Closing the door turns off the light.
Reversible Dryer Door
Your dryer is equipped with a reversible door. The door can be hinged on the
right or left side, Refer to the INSTALLATION iNSTRUCTIONS for directions
on changing the door.
Drying Rack (some models)
Use the drying rack to dry items which should not be tumble dried.
1° Open the dryer door and remove the tintscreen.
2. insert drying rack into the dryer drum Pface the front bar under the lip of
the lint screen opening.
& Place items to be dried on top of the rack. Weight should not exceed 10
lbs. Leave space between items, but do not let items hang over the sides
or through the grids. Do not tumble other items when using the drying
rack.
4. Select a timed dry setting best suited for items being dried. Use only the
Air Fluff (no heat) temperature setting for items containing plastic, foam
rubber, rubber-like materials, feathers or down_.
5. When items are dry, remove the rack and replace the ii_screen If lint
screen is not in place, tumbling items could enter the exhaust system and
cause damage to the dryer.
Common Drying Problems
Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric
damage. For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association.
PROBLEM
Greasy,oily
stains
Lint
Pilling
(Fibers break
off, bali up and
cling to fabric.)
Shrinking
Wrinkling
POSSIBLE CAUSES SOLUTIONS PREVENTIVE MEASURES
• Fabric softener sheet,, . Rubfabric softener stains with bar • Add a f6w bath towels to small loadsfor
soap. Rinse and rewash, proper tumbling..
J,
Overloading:
Overdi'ying causes static
etectrictfy,
Lint screen not clean
when cycle began,
Lint is attached to "pills,"
- Some "silk-like" fabrics should be air
dried,
• Use proper drying temperature,
• Place fabric softener sheet on top of load
before starting the dryer.
Do not overload dryer,
Use fabric softener In washer or dryer to
reduce static electricity°
Remove items when they are slightly
damp to avoid overdrytng.
Check that fint screen is clean and in
place.
• Reduce toad size and rewash using •
liquid fabric softener in the final rinse. •
• Or, add a fabric softener sheet and
tumble without heat.
• Use lint brush or roller to remove lint.
Pilling is normal with
synthetic and permanent
press fabrics. This is due
to abrasion from normal
wear,
• Use a lint brush or shaver to remove
pills
• Use fabric softener to lubricate fibers,
• Whenironing, use spray starch or fabric
finish on collars and cuffs,,
• Turn items inside out to reduce abrasion
• Overdrying.
• Overloading,
• Leaving items in dryer
after cycle ends,
• Irreversible condition.
• Follow fabric care label directions.
• tf shrinking is a concern, check toad often.
• Remove items while slightly damp and
hang or lay fiat to complete drying_
• Block knits into shape.
• Reduce load size and tumble at
medium of low heat for 5-10 minutes, •
• Remove items immediately Hang or
fold 6
Do not overload dryer.
Remove items as soon as cycle ends,
Loading ...
Loading ...
Loading ...