Loading ...
Loading ...
Loading ...
GENERAL RECOMMENDATIONS
The warranty of the high pressure washer does not
cover items that have been subjected to operator
abuse or negligence. To receive full value from the
warranty, operator must maintain high pressure
washer as instructedin this manual.
Some adjustments will need to be made periodically
to properly maintain your high pressure washer.
All adjustments in the Service and Adjustments sec-
tion of this manual should be made at least once
each season.
o Once a year you should clean or replace the
spark plug and clean or replace the air filter and
check the gun and wand assembly for wear. A
new spark plug and clean air filter assure proper
fuel-air mixture and help your engine run better
and last longer.
PRODUCT SPECIFICATIONS
Pressure Washer Specifications
PRESSURE 1650 psi
FLOWRATE 2 GPM
DETERGENTMIX
Use undiluteddeterqent....
WATER SUPPLY
TEMPERATURE Not to Exceed 140°F
Engine Specifications
ENGINE MODEL Briq,qs& Stratton
,RATED HORSEPOWER 3.8
DISPLACEMENT t58cc
SPARK PLUG: Type:
Set Gap to:
: GASOLINE CAPACITY
[ *"'"', .... ,
. Q!L(20 oz. capacity)
SOLID STATE IGNITION
AIR GAP
Champion RJ-BC
or equivalent
0,030 inch (0,76turn)
1 U.S. Quart
SAE 30 weight
0.0125inch
In the State of California a spark arrestor is required
by law (Section 4442 of the California Public
Resources Code). Other states may have similar
laws. Federal laws apply on federal lands.
Note: If you equip the engine of your pressure wash- •
er with a spark arrestor muffler, the spark arrestor
must be maintained in effective working order by the °
owner/operator.
You can order a spark arrestor through your Sears °
Service Center. •
BEFORE EACH USE
= Check water inlet screen for damage.
- Check high pressure hose for leaks.
• Check detergent inlet hose and filter for damage.
• Check gun and wand assembly for teaks.
• Purge pump of air and contaminants.
, Check engine oil level.
PRESSURE WASHER MAINTENANCE
Check and Clean Inlet Screen: Remove quick-con*
nect and examine inlet screen on the female connec-
tor. Clean if it is clogged or replace if it is torn.
Check High Pressure Hose: High pressure hose
can develop leaks from wear, kinking, abuse. Inspect
hose each time before using it. Check for cuts, leaks,
abrasions or bulging of cover, or damage or move-
ment of couplings. If any of these conditions exist,
replace hose immediately.
Check Detergent Hose: Examine the filter on the
detergent hose and clean if clogged. Hose should fit
tightly on barbed fitting. Examine hose for leaks or
tears. Replace the filter or hose if either is damaged.
A
DANGER: Water spraying from a leak is
capable of injecting material into skin.
NEVER repair high pressure hose.
Replace with hose that meets minimum
pressure rating of your pressure washer.
Check Gun and Wand: Examine hose connection to
gun and make sure it is secure. Test trigger by press-
ing it and making sure it springs back into place when
you release it. Put safety latch in UP position and test
trigger. You should not be able to press trigger.
Purge Pump of Air and Contaminants
To remove the air from the pump, follow these steps:
= Set up the pressure washer as described in the
ASSEMBLY section and connect the water sup-
ply.
- Remove the wand extension from the gun.
- Pull the trigger on the gun and hold.
To remove the contaminants from the pump, follow
these steps:
° Set up the pressure washer as described in the
ASSEMBLY section, and connect the water sup-
ply.
Remove the nozzle attachment from the gun.
Start the engine according to instructions in
OPERATION section.
Pull the trigger on the gun and hold.
When the water supply is steady and constant,
engage the safety latch and refasten the nozzle
attachment.
11
Loading ...
Loading ...
Loading ...