5. Once connections of wires are
completed, carefully tuck wires and
wire nuts into the outlet box making
sure no bare wire (on the black and
white) is visible at the wire nuts. Slide
canopy into position and tighten in
place by nut into position.
6. Slightly push the glass onto the
cover. Ensure the glass is tightenly
secured by the 3 spring clips.
7. Hook the support arms onto
fixture and then into the hoop.
8. Install specified bulb type and
wattage (not included).
SAFETY PRECAUTIONS:
CHANDELIER
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
3. CONNECT THE GROUND WIRES (BARE COPPER OR GREEN) FROM YOUR FIXTURE TO THE GROUND
WIRE (BARE COPPER OR GREEN) OR GROUND SCREW IN THE ELECTRICAL BOX.
Power
Cord
Chain
Connector
Lower
Nipple
Hex Nut
Electrical Box
Electrical Box Screws
(not included)
Mounting
Bracket
Canopy
Nipple
Upper
Connector
Nut
1 . Attach the mounting
bracket to the electrical box using
electrical box screws (not
included) . Attach the nipple to
the mounting bracket and adjust
until it will clear the canopy when
assembled (Place the canopy over
the nipple and tighten the upper
connector onto the nipple until
snug. The upper connector
should hold the canopy snug to
the ceiling). Lock the nipple in the
correct position using the hex nut.
2. To attach chain loop to light
fixture, use a screwdriver and
wrench to open and close chain
loop. Ensure to close the
opening. Weave the power cord
and ground wire through the links
in the chain.
3. Loosen the nut on the upper
connector and slide it down the
chain towards the lower
connector. Slide the canopy down
the chain towards the lower
connector. Feed the wire
through nut, canopy, the upper
connector and onto the nipple.
Tighten the upper connector onto
the nipple. Spread the other end
of the chain open and fasten to
the upper connector. Ensure the
opening is closed.
4. Connect the ground wires
(bare copper or green) from your
fixture to the ground wire (bare
copper or green) or ground screw
in the electrical box. Connect the
black wire (or wire marked
“SPT-1”) from the fixture to the
black wire in the electrical box and
connect the white wire from the
fixture to the white wire in the
electrical box.
TOOLS AND MATERIALS REQUIRED:
Phillips
Screwdriver
Wire Cutters
Pliers Wrench
Wiring supplies
as required by
the Canadian
Electrical Code
and/or the
Quebec
Electrical code
!
INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS
READ ALL INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Canopy
Nut
White
Black
House supply
Ground wire
Fixture
Ground
wire
INSTALLATION:
Upper
Connector
Nipple
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: (613) 342-5424, Fax: (800) 263-4598
L
I
G
H
T
I
N
G
&
F
A
N
S
E
C
L
A
I
R
A
G
E
S
&
V
E
N
T
I
L
A
T
E
U
R
S
QUESTIONS OR CONCERNS CONTACT CANARM AT:
1-800-265-1833 (English) / 1-800-567-2513 (French)
Monday through Friday 8:00 AM to 5:00 PM E.S.T.
(NOTE: Product May Not Look Exactly As Shown In Figures.)
Bulb
ICH624A04
10/15
Spring Clip
Glass
Cover
Support
Arm
Hoop
