Loading ...
Loading ...
Loading ...
14
If you experience Possible Causes Solution
Dryer Results (cont.)
Clothes are not drying
satisfactorily, clothes are
balling or tangling, or
drying times are too long
(cont.)
The load is too large and heavy to
dry quickly.
Separate the load to tumble freely.
)DEULFVRIWHQHUVKHHWVDUHEORFNLQJ
the grille.
The air outlet grille is just inside the door, behind the lint screen.
Check that it is not blocked by a fabric softener sheet. Use only
one fabric softener sheet, and use it only once.
The dryer is located in a room with
WHPSHUDWXUHEHORZ)&
Proper operation of dryer cycles requires temperatures above
)&
The dryer is located in a closet. Closet doors must have ventilation openings at the top and
bottom of the door. The front of the dryer requires a minimum
of 1" (25 mm) of airspace, and, for most installations, the rear
RIWKHGU\HUUHTXLUHVPP6HHWKH,QVWDOODWLRQ,QVWUXFWLRQV
Cycle time is too short The load may not be contacting the
sensor strips on Sensing Cycles.
Level the dryer. See the Installation Instructions. All four dryer feet
VKRXOGEHLQoUPFRQWDFWZLWKWKHpRRU
Clothes are coming out of the Steam
Refresh cycle with damp or wet spots.
If you are doing a Steam Refresh cycle of 1 or 2 items, you can
add a towel to the load to help avoid uneven spraying from the
steam valve. Then select the appropriate temperature based on
the load to be refreshed.
The sensing cycle is ending early. Change the dryness level setting on Sensing Cycles. Increasing
or decreasing the dryness level will change the amount of drying
time in a cycle. If loads are consistently ending too early, see also
“Changing the Sensing Cycle settings to increase or decrease
drying time.”
Lint on load Lint screen is clogged with lint. Clean lint screen before each load.
Stains on load Improper use of fabric softener. Add dryer fabric softener sheets at the beginning of the cycle.
)DEULFVRIWHQHUVKHHWVDGGHGWRDSDUWLDOO\GULHGORDGFDQVWDLQ
your garments. Do not use fabric softener sheets with steam
cycles.
Stains on drum Loose dyes in clothes. Drum stains are caused by dyes in clothing (usually blue jeans).
These will not transfer to other clothing.
Loads are wrinkled The load was not removed from dryer
at the end of the cycle.
Select Steam Refresh cycle to tumble the load with water and
heat. This cycle is best for smoothing out wrinkles and reducing
odors from dry loads consisting of wrinkle-free cotton, cotton-
polyester blends, common knits, and synthetics.
NOTE: Refer to garment care label instructions. Dry-clean-only
garments are not recommended.
The dryer was tightly packed. Dry smaller loads that can tumble freely. Results may also vary
depending on fabric type.
)RUVWHDPF\FOHVWKHZDWHULVQRW
properly connected with the dryer.
Make sure water is connected to the dryer. Check that water inlet
hose is connected to both the faucet and dryer’s water inlet valve.
Check that the water supply is turned on.
2GRUV Recent painting, staining, or varnishing
in the area where your dryer is
located.
Ventilate the area. When the odors or fumes are gone from the
area, rewash and dry the clothing.
)RUVWHDPF\FOHVWKHZDWHULVQRW
properly connected with the dryer.
Make sure water is connected to the dryer. Check that water inlet
hose is connected to both the faucet and dryer’s water inlet valve.
Check that the water supply is turned on.
2GRUVDUHOHIWLQJDUPHQWVDIWHU
wearing.
To remove odors left in garments after wearing, select Steam
Refresh. This cycle is best for reducing wrinkles and odors from
dry loads consisting of wrinkle-free cotton, cotton-polyester
blends, common knits, and synthetics.
Steam did not occur
during Wrinkle Guard™
Wrinkle Guard™ does not
HQDEOH6WHDPRQDOOF\FOHRSWLRQ
combinations.
Refer to “Cycle Guide” to verify which cycles and settings enable
Steam.
)LUVWWU\WKHVROXWLRQVVXJJHVWHGKHUHIRUDVVLVWDQFHDQGWRSRVVLEO\DYRLGDVHUYLFHFDOO
TROUBLESHOOTING
Loading ...
Loading ...
Loading ...