Loading ...
Loading ...
Loading ...
.._ .ITI.I i.ii .................... i ............................. i
CUSTOMER RESPONSiBiLITiES
TRACTOR
Always observe safety rules when performing any mainte-
r_ance°
BRAKE OPERATION
If tractor requires more than six (6) feet stopping distance
at high speed in highest gear, then brake must be adjusted.
(See "TO ADJUST BRAKE" in the Service and Adjust-
ments section of this manual).
TIRES
• Maintain proper air pressure in all tires (See "PROD-
UCT SPECIFICATIONS on page 3 of this manual).
• Keep tires free of gasoline, oil, or insect control chemi-
cals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp objects and
ether hazards that may cause tire damage°
NOTE; To seal tire punctures and prevent fiat tires due to
siow leaks, tire sealant may be purchased from your local
parts dealero Tire sea_ant also prevents tire dry rot and
corrosion.
BLADE CARE
For best results mower blades must be kept sharp. Re-
place bent or damaged blades..
BLADE REMOVAL (See Fig. 13)
- Raise mower to highest position to allow access to
blades.
. Remove hex bo_t,lockwasher and flat washer securing
blade.
° install new or resharpened blade with trailing edge up
towards deck as shown.
. Reassemble hex bolt, lock washer and flat washer in
exact order as shown.
= Tighten bolt securely (30-35 Ft. Lbs. torque).
IMPORTANT: BLADE BOLT 1SGRADE 8 HEATTREATED.
NOTE: We do not recommend sharpening blade- but if you
do, be sure the b_ade is batanced_
BLADE MANDREL
FIG. 13
iii1..i.,.., i1.111111.111ii
TO SHARPEN BLADE (See Fig. 14)
Care should be taken to keep the blade balanced. An
unbalanced blade will cause excessive vibration and even-
tual damage to mower and engine_
• The blade can be sharpened with a file or on a grinding
wheel. Do not attempt to sharpen while on the mower.
° To check blade balance, you will need a 5/8" diameter
steel bolt, pin, or a cone balancero (When using a cone
balancer, follow the instructions supplied with bal-
ancer) o
- Slide btade on to an unthreaded portion of the steel bolt
or pin and hold the bolt or pin paraIlel with the ground.
if blade is balanced, it shouId remain in a horizontal
position, if either end of the blade moves downward,
sharpen the heavy end until the blade is balanced.
NOTE: Do not use a nail for balancing blade. The lobes of
the center hole may appear to be centered, but are not.
CE. ER.OL / /
FIG. 14
BATTERY
Your tractor has a battery charging system which is suffi-
cient for normal use. However, periodic charging of the
battery with an automotive charger wilt extend its life.
o Keep battery and terminals clean.
. Keep battery bolts tight.
• Keep small vent holes open.
. Recharge at 6-'10 amperes for I hour°
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and terminals can cause
the battery to "leak" power.
• Open battery box door.
° Disconnect BLACK battery cable first then RED bat-
tery cable and remove battery from tractor.
• Rinse the battery with plain water and dry.
• Clean terminals and battery cable ends with wire brush
until bright.
Coat terminals with grease or petroleum jelly.
• Reinstall battery (See "CONNECT BATTERY" in the
Assembly section of this manual).
V-BELTS
Check V-belts for deterioration and wear after 100 hours of
operation and replace if necessary. The belts are not
adjustable. Replace belts if they begin to slip from wear.
17
TRANSAXLE COOLING
The fan and cooling fins of transmission should be kept
clean to assure proper cooling.
Do not attempt to clean fan or transmission while engine is
running or while the transmission is hot.
Loading ...
Loading ...
Loading ...