Loading ...
Loading ...
Loading ...
Page 4 of 7
FUNCTION AND OPERATION
Choose a mode by sliding the slide switch.
Note: The light will turn on immediately when power is applied. Wait for 30 seconds to allow the sensor to
warm up.
1. Test MODE (daytime and nighttime operation.)
● Rotate "Time/Test" knob arrow clockwise to point the "Test" position.
motion is detected, and stay on as long as the motion continues. The light will turn to the low-level brightness you
set after 5 seconds when motion is no longer detected.
2. Auto MODE (nighttime operation only)
● To shift to the "AUTO" mode, slide switch to "AUTO" position, and rotate "Time/Test" knob arrow counterclockwise
to point to the desired time setting (5~180 seconds).
● At dusk, the light will turn to low-level brightness (0~50%). The light will turn to high-level brightness (full brightness)
when motion is detected, and stay on as long as the motion continues. When the motion stops, the light will remain
on for the predetermined time set (5~180 seconds), and then turn to the low-level brightness you set.
● The light will turn off automatically at dawn.
3. PC MODE (nighttime operation only)
● To shift to the "PC" mode, slide switch to "PC" position, and rotate "Time/Test" knob arrow counterclockwise away
from "Test" position.
● The light will turn on (full brightness) automatically at dusk and turn off automatically at dawn.
4. 3H MODE (nighttime operation only)
● To shift to the "3H" mode, slide switch to "3H" position, and rotate "Time/Test" knob arrow counterclockwise to
point to the desired time setting (5~180 seconds).
● At dusk, the light will turn to high-level brightness (100% brightness). The light will turn to low-level brightness
(0% ~50% brightness) automatically after 3 hours. The light will turn to high-level brightness (100% brightness)
when motion is detected, and stay on as long as the motion is continuing. When motion is no longer detected,
the light will remain on for the predetermined time you set (5~180 seconds), and then revert to low-level
brightness you set.
● Light will turn off automatically at dawn, and return to 3H mode at dusk.
211201
● The light will turn to low-level brightness (0~50%).The light will turn to high-level brightness (full brightness) when
Auto Mode
3H Mode
Manual
Override
Manual Override Operation Diagram
Turn wall switch OFF-ON
in 0.5~3 Seconds
Turn wall switch OFF-ON
in 0.5~3 Seconds
Fig. 4
6. Manual Override MODE (nighttime operation only)
● Rotate "Time/Test" knob arrow counterclockwise away from "Test"
position.
● To shift to the manual override mode, set the switch to ″Auto″ or
″3H″ mode. Turn the wall switch ″OFF″ and then turn it ″ON″
within 3 seconds. The light will stay on through all night. To restore
to the ″Auto″ or “3H” mode, turn the wall switch ″OFF″ and then turn
it ″ON″ within 3 seconds again. (See Fig.4)
● The light will last for one night only and turn off automatically at dawn.
Note: 1. The low level brightness can be adjusted from 0 to 50% by
rotating “Low level” knob. (See Fig.5)
2. Always keep the wall switch in the “ON” position (including the daytime).
3. Please notice the warm up time is 30 seconds, any operations are invalid during this time.
5. Custom MODE (nighttime operation only):
● To shift to the "Custom" mode, slide switch to "Custom" position, and rotate "Time/Test" knob arrow counterclockwise
to point to the desired time setting (5~180 seconds).
● In "Custom" mode, the light will turn on to full brightness at dusk and off at dawn automatically.
● In this mode, the light can also be set to dim to an adjustable low-level brightness (0~50%) with full brightness upon
motion detection, similar to "AUTO" mode. To make this happen, toggle the wall switch "OFF" and back "ON" within
3 seconds. The light will remember the time that this selection was made and this transition to low-level with
motion-sensing will reoccur each following night at the same time. For example, if a homeowner wants to have the
light stay on full brightness from dusk until 8:00pm before dimming to low-level each night, then they would turn the
wall switch "OFF" and back "ON" within 3 seconds at 8:00pm. The light will remember this operation for each following
night.
● To revert to Default, turn the wall switch "OFF" and then turn it "ON" after 5 seconds.
Note: You can adjust the low-level brightness (0~50%) by using the low-level brightness (0~50%) knob.
Loading ...
Loading ...
Loading ...