Loading ...
Loading ...
Loading ...
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have nished.
40
2.5 To Replace a Hotplate Burner
n
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the hotplate tray (see 2.1). The burners (except
the right-hand wok burner) are mounted on support struts.
For these burners, disconnect the burner feed pipes at the
burner. Remove the screws at the front and rear holding the
support struts. Lift the strut and burners clear. The burners
are xed to the support struts with 2 screws. Remove the
appropriate burner and t the new one.
Reassemble in reverse order. Check that the burner operation
is satisfactory.
Right-hand Wok Burner
Disconnect the burner feed pipe at the burner.
Fit the new one and reassemble in reverse order. Check that
the burner operation is satisfactory.
2.6 To Change a Hotplate Burner Thermocouple
n
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel and hotplate (see 1.1 & 2.1).
Unplug the FSD lead from the rear of the tap.
The thermocouple sits in a hole that has a slot at one side.
Ensure that the thermocouple is cool. Turn the thermocouple
so that the earth lead (no sleeve) is in line with the slot. Lift
the thermocouple clear of the hole.
Reassemble in reverse order.
3. Controls
3.1. To Replace the Ignition or Light Switch
n
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel (see 1.1).
Note: The old switch may be destroyed during removal.
Remove the old switch from its bezel by gripping the switch
body behind the control panel and twisting sharply. Remove
the switch bezel by folding back the locking wings and
pushing forward.
To t the new bezel to the control panel: rst line up the
raised key on its body with the cut-out in the control panel
and push it in from the front.
Assemble the new switch to the bezel by lining up the key
sections and pushing home. Fit the new button by pushing in
from the front.
Replace the control panel in the reverse order and test for
correct operation.
3.2 To Replace the Clock
n
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel (see 1.1). Pull o the timer control
buttons.
Undo the timer xing screws and remove the timer/mounting
bracket assembly from the control panel.
Remove the timer from its mounting bracket by depressing
the plastic lugs on the timer case, and at the same time
pulling the unit forward.
Reassemble in reverse order. When replacing the leads, refer
to the wiring diagram. Check the operation of the timer.
3.3 To Change the Ignition Generator
n
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Pull the cooker forwards to gain access to the cover box at the
rear of the cooker. Remove the screws securing the cover and
lift clear. Pull o all the leads to the generator noting their
positions. Slacken the 2 screws holding generator to cooker
and remove the generator.
Fit the new generator to the cooker and replace the leads.
Refer to the wiring diagram and reassemble in reverse order.
Check ignition performance.
4. Grill
4.1 To Replace the Grill Controller
n
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel and hotplate (see 1.1 & 2.1).
Disconnect the wiring from controller. Remove the 2screws
holding the controller to the mounting panel.
Fit the new controller and reassemble in the reverse order.
Check for correct operation.
4.2 To Replace the Grill Element
n
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the grill pan from the grill chamber. From inside
the grill compartment, undo the 2 screws and washers
and remove the enamelled front shield from the grill roof.
Remove 2 screws and washers securing the grill element front
support. Remove the screws from the grill elements.
Carefully lift the elements out and disconnect the leads from
the element terminals, noting their position.
If it is not possible to disconnect the leads in this way, pull
cooker forwards to gain access to the rear.
Remove the screws securing the electric cover to the back
sheet, and then remove cover and disconnect the terminals
from the rear.
Fit the new elements and reassemble in reverse order. Check
the operation of the grill.
Loading ...
Loading ...
Loading ...