Loading ...
FORMULA RATIO CHART
SMALL AREA (20 OZ) LARGE AREA (40 OZ)
IF USING HOOVER CONCENTRATE
Water Fill water Small Area Line (20 oz) Fill water Large Area Line (39 oz)
HOOVER 2X Concentrated Formula 0.5 oz 1 oz
Clean Complements Enhancer Up to 1 oz Up to 1 oz
IF USING HOOVER READY-TO-USE PREMIX
Premixed Formula Fill premix Small Area Line Fill premix Large Area Line
Clean Complements Enhancer Up to 1 oz Up to 1 oz
HOW TO CLEAN TOOLS
Remove Insert and rinse under faucet.
Remove the tool from the hose. Rinse
hand tool under faucet. Remove the
nozzle cover by unlatching the clear tab.
PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION
Cleaner won’t run
1. Power cord not firmly plugged into outlet.
1. Plug unit in firmly.
2. Blown fuse or tripped breaker. 2. Check fuse or breaker in home. Replace fuse⁄reset breaker
in home.
3. Needs service. 3. Visit our website at www.hoover.com or call 1-800-944-9200.
Cleaner won’t pick-up or low
suction
1. Recovery Tank is not installed correctly. 1. Check placement of Recovery Tank in base of cleaner.
2. Recovery Tank is full. 2. Empty Recovery Tank.
3. Recovery Tank is clogged. 3. Clean Recovery Tank.
4. Air path is clogged.
5. Recovery Tank debris filter is clogged.
4. Remove Hose and Flush out with Clean Water.
5. Remove debris filter and rinse thoroughly, then replace.
Water escaping from Cleaner 1. Recovery Tank is full. 1. Empty Recovery Tank.
2. Recovery Tank is not installed correctly. 2. Check placement of Recovery Tank in base of cleaner.
3. Solution Tank not installed properly. 3. Review “Getting Started” for Solution Tank Installation.
Cleaner won’t dispense
1. Solution Tank is empty. 1. Fill Solution Tank.
2. Solution Tank not installed properly. 2. Review “Getting Started” Solution Tank Installation.
3. Needs service. 3. Visit our website at www.hoover.com or call 1-800-944-9200.
Hose nozzle will not spray after
filling the Clean Water Tank or
Solution Tank Container.
1. Air is trapped in the pump and hose. 1. Turn on the cleaner. If hose dœs not spray, prime the pump by
lowering the hose down to the floor and hold the trigger for up
to 1 minute.
Motor noise becomes
high-pitched
1. Recovery Tank is full. 1. Empty Recovery Tank.
2. Recovery Tank is clogged. 2. Clean the Recovery Tank.
3. Air path is clogged. 3. Unclog air path.
4. The float in the Recovery Tank has been activated. 4. Review Cleaning the Recovery Tank.
TROUBLESHOOTING
REPLACEMENT PARTS AND ACCESSORIES SUCH AS SOLUTIONS AVAILABLE AT HOOVER.COM.
IF APPLIANCE IS NOT WORKING AS IT SHOULD, HAS BEEN DROPPED, DAMAGED, LEFT OUTDOORS, OR DROPPED INTO WATER, CALL CUSTOMER
SERVICE AT 1-800-944-9200 PRIOR TO CONTINUING USE.
ALWAYS IDENTIFY YOUR CLEANER BY THE COMPLETE MODEL NUMBER. (THE MODEL NUMBER APPEARS ON THE BOTTOM OF THE CLEANER.)
WARNING:
To reduce the risk of personal injury - Unplug before cleaning
or servicing.
1
Remove Solution Tank from the side of
the unit, then remove the cap.
GETTING STARTED
CLEANING FLUID: SEE THE HOOVER
SOLUTION GUIDE insert or visit Hoover.
com/cleaning-solutions.
2
3
4
Follow the formula ratio chart to add
cleaning formula in the Solution Tank.
Replace and tighten cap. Slide the tank
back into the unit. The tank is secured
when you feel a click.
Unwrap hose from unit. Select preferred
tool and make sure it is attached securely.
NOTE: Read the directions on the HOOVER®
Carpet Cleaning fluid prior to use.
CAUTION:
Not to be used for
grooming a pet.
CAUTION:
DO NOT USE THIS
EXTRACTOR ON HARD FLOORS. USING
THIS PRODUCT ON HARD FLOORS MAY
SCRATCH OR DAMAGE YOUR FLOOR.
Before You Begin Cleaning
Use your Hoover upholstery and spot cleaner
only if upholstery fabric is marked with a “W”
(for “wet” clean) or “S/W” (for “solvent/dry”
or “wet” clean). Don’t clean fabric marked “S”
(“solvent/ dry” clean only).
Test for colorfastness in a small, hidden area.
Gently rub surface with a dampened white
cloth. Wait ten minutes and check for color
removal or bleed with a white paper towel.
NOTE: To prevent staining, use plastic or
aluminum foil to protect wood or metal
surfaces from possible water spray.
NOTE: To avoid damage to wood floors
underneath area rugs or carpet, place
waterproof material (e.g. plastic) underneath
them before cleaning.
THERMAL PROTECTION
A thermal protector has been designed
into your cleaner to protect it from
overheating. When the thermal protector
activates the cleaner will stop running.
If this happens proceed as follows:
1. Turn cleaner OFF and unplug it from
the electrical outlet.
2. Empty Recovery Tank.
3. Inspect for any obstructions.
Clear obstructions if present.
4. When cleaner is unplugged and motor
cools for 30 minutes, the thermal
protector will deactivate and cleaning
may continue.
If the thermal protector continues to
activate after following the above steps,
your cleaner needs servicing.
WARNING:
To reduce the risk
of personal injury - Unplug before
cleaning or servicing.
This product contains no serviceable parts.
If appliance is not working as it should, has
been dropped, damaged, left outdoors, or
dropped into water, call customer service at
1.800.944.9200 prior to continuing use.
HOW TO CLEAN THE RECOVERY TANK
Press TANK RELEASE button then lift lid
o for emptying and rinsing. Clean water
will help remove dirt & debris from the
tank. Let air dry before reinstalling.
1
MAINTENANCE
1
2
3
Press Red Power button on top of unit to
turn ON.
Hold tool about 5 inches over the spot
or stain. Spray a generous amount of
cleaning solution over the soiled area
by pressing the trigger behind the tool
and scrub the stain in a back and forth
motion.
To lift the stain, suction up the dirt and
cleaning solution by applying downward
pressure on the front of the cleaning
tool and pulling towards you. Repeat as
needed.
IMPORTANT: Empty the Recovery Tank
when it reaches the MAX fill line or you
hear an audible change. Ensure the tank
is secured before cleaning. Ensure the
tank is secured before cleaning.
OPERATION
STORAGE: Wrap cord around the cord
hooks for convenient storage. Attach the
plug end to the cord.
For fast cord release, simply turn the
cord wraps 180 degrees to the right
or left.
For best results, pretreat stains with a
HOOVER® spot treatment (see HOOVER®
Cleaning Solution Guide) to help loosen and
remove even the most stubborn stains.
Distribute a generous amount of pretreat spray
on spot, stain, or high trac area.
Always follow specific directions found on
solution label.
Wait 5-10 minutes before using machine.
CAUTION:
Do not clean over
floor electrical outlets. Water will
drip from the tool after use and may
puddle. To avoid damage to wood
and laminate flooring and to avoid
potential slip hazard, after use (a)
do not leave the product on wood
and laminate surfaces and move to
a hard surface and (b) place unit on
an absorbent material (such as a
towel) to soak up drips.
WARNING:
To reduce risk of
fire and electric shock due to
internal component damage, use
only HOOVER® cleaning products
intended for use with the appliance
as noted.
LUBRICATION: The motor is equipped
with bearings which contain sufficient
lubrication for their lifetime. The addi-
tion of lubricant could cause damage.
Do not add lubricant to motor bearings.
1
2
HOW TO CLEAN HOSE
Remove the solution tank and fill with
warm water (max 140˚F (60˚C)) to the
small area fill line.
1
HOW TO CLEAN HOSE (CONT’D)
Remove any cleaning tool or attachment
from the hose, and attach the Hose
Rinse Tool to the hose.
Ensure both the solution and recovery
tanks are secured on unit. Turn unit on
and hold the trigger for 30 seconds. The
clean water will rush through the hose,
eectively cleaning and removing odor
causing bacteria left in the hose. Repeat
as needed. Let unit run for 5-10 seconds
before turning o.
Repeat process as needed and turn o
the unit when hose is fully clean. Empty
the recovery tank.
2
3
4
Tools and formula may vary by model.
Loading ...
Loading ...