Loading ...
Loading ...
Loading ...
English
12
Hot Weather Operation
Tool should operate normally. However, keep tool out of
direct sunlight as excessive heat can deteriorate bumpers
and other rubber parts resulting in increasedmaintenance.
Cold Weather Operation
When operating tools at temperatures below freezing:
Keep tool as warm as possible prior touse.
Actuate the tool 10 or 15 times into scrap lumber
beforeusing.
Non-Mar Tip (Fig.O)
WARNING: Always remove battery pack before
attaching the non‑martip.
When using this tool on softer materials that you do not
want to mark, such as wood cladding, use the plastic non‑
mar tip
19
over the contact trip
8
.
instructions on clearing a stalled condition. Next
remove battery pack and then reinsert battery pack.
The tool will now be operational.
If the nailer is used in a rigorous application where all
available energy in the motor is used to drive a fastener, the
tool may stall. The driver blade did not complete the drive
cycle and the jam/stall indicator will flash. Rotate the stall
release lever
6
on the tool and the mechanism will release .
nOTE: The tool will disable itself and not reset until the
battery pack has been removed and reinserted. If the unit
continues to stall please review the material and fastener
length to be sure that it is not too rigorous an application. If
the driver blade does not automatically return to the home
position after rotating the stall release lever, proceed to
Clearing a Jammed Nail.
Clearing a Jammed Nail (Fig.M, N)
If a nail becomes jammed in the nosepiece, keep the tool
pointed away from you and follow these instructions toclear:
1. Remove battery pack from tool and engage the trigger
lock‑off.
2. Remove any loaded nails. Refer to Loading and
Unloading the Tool.
3. Lift the jam clearing latch
7
then pull up to open
frontdoor
17
.
4. Remove bent nail, using pliers if necessary.
5. If driver blade is in the down position, cycle stall release
lever
6
using enough force to fully slide it to the other
end of the slot in housings.
6. Close the front door and engage the latch pin under the
two arms
18
on the nosepiece. Push latch until it locks
in place.
7. Reinsert battery pack.
nOTE: The tool will disable itself and not reset until the
battery pack has been removed and reinserted.
8. Reinsert nails into magazine (see To Load the Tool).
nOTE: Should nails continue to jam frequently in
nosepiece, have tool serviced by an authorized
servicecenter.
Loading and Unloading the Tool (Fig.I, J)
WARNING: Keep the tool pointed away from yourself
and others. Serious personal injury may result.
WARNING: Never load nails with the contact trip or
trigger activated. Personal injury may result.
WARNING: The battery should always be removed and
the trigger lock‑off engaged whenever any adjustments
are made or when tool is not in use.
To Load the Tool
1. Press pusher latch
10
and pull magazine down.
2. Insert fasteners into the side of the magazine. Ensure
the fastener tips are placed towards the front of the
magazine, under the nail guide
16
in the nail channel.
3. Push magazine closed until it locks into place.
CAUTION: Keep fingers clear of pusher to
preventinjury.
To Unload the Tool
1. Press the nail pusher latch and pull the magazine down.
2. Tip the tool up until the nails slide freely out of
themagazine.
3. Open the jam clear door on the contact trip to verify
there are no nails remaining.
Using the Nailer
WARNING: The contact trip needs to be depressed
followed by a full trigger pull for each nail followed
by a release of both the contact trip and trigger after
each nail.
WARNING: The battery should always be removed and
the trigger lock‑off engaged whenever any adjustments
are made or when tool is not in use.
1. Fully depress contact trip against the work surface.
2. Fully pull trigger and motor will start. (nail will drive into
work surface).
3. Release trigger.
4. Lift contact trip off work surface.
5. Repeat steps 1 through 4 for next application.
Worklights (Fig.K)
There is a worklight
5
located on each side of the nailer.
Worklights turn on upon battery insertion, activation of the
trigger, or depressing the contact trip.
nOTE: These worklights are for lighting the immediate work
surface and are not intended to be used as flashlights.
lOW BATTERY inDiCATOR: The left‑side worklight will
flash four consecutive times and then shut down to indicate
low battery.
JAMMED nAil inDiCATOR: The right‑side worklight will
flash continually if a nail becomes jammed in the nosepiece
(see Clearing a Jammed Nail).
Stall Release (Fig. L)
WARNING: If a stall occurs, the tool will disable
itself and will require you to reset it. To do so, follow
Loading ...
Loading ...
Loading ...