User Manual Dimplex DXC30FTI 3kW Contrast Convector Heater with Turbo Fan and Timer

Documents for Dimplex DXC30FTI

The following documents are available:
User Manual Other Documents
  • Contrast Convector Issue 0%5B1%5D - (English) Download
  • Dimplex DXC Contrast Convectors Issue 5 - (English) Download
  • DXC30FTI - (English) Download
Photos
DXC30FTI photo
Installation and Operating Instructions
Dimplex Convector Heaters
INDCUKDX2R Issue 6
Models : DX200, DX200S, DXW200S, DX200T,
DX300S, DX300T and DX300TF.
357
432
MIN
Floor Mtd. Wall Mtd.
230
230
MIN
577 - 2.0kw
697 - 3.0kw
230 156
MIN
450
MIN
3 No. Wall
Mounting
Brackets
floor
520 mm
min.
3
k
w
-
4
7
8
m
m
c
e
n
t
r
e
s
2
k
w
-
3
5
8
m
m
c
e
n
t
r
e
s
526 mm
min.
bracket
slot
shelf /
ceiling
Dimensions
(millimetres)
Model(s) Specification
DX200 2.0kw + Thermostat
DX200S 2.0kw + Thermostat + Switch
DXW200S 2.0kw + Thermostat + Switch (Wall Mtd.)
DX200T 2.0kw + Thermostat + 24hr Timer
DX300S 3.0kw + Thermostat + 2 Switches
DX300T 3.0kw + Thermostat + 24hr Timer
DX300TF 3.0kw + Thermostat + 24hr Timer + Turbo
IMPORTANT SAFETY ADVICE
WARNING –THIS APPLIANCE MUST NOT BE USED IN A BATHROOM
WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE
SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING POOL.
WARNING – THIS HEATER MUST NOT BE LOCATED IMMEDIATELY
BELOW A FIXED SOCKET OUTLET.
DO NOT USE THE HEATER UNTIL THE FEET OR WALL BRACKETS
ARE FITTED CORRECTLY.
FOLLOW these instructions carefully.
NEVER cover or obstruct in any way the heat outlet slots at the top
of the heater or the air inlet slots in the base of the heater.
The heater carries a warning ‘DO NOT COVER’ to alert the user to the
risk of fire that exists if the heater is accidentally covered.
Models DX200T, DX300T, DX300TF can be set to switch on
automatically. Remember to observe all safety warnings at all times.
This appliance is not intended for use by children or other persons
without assistance or supervision if their physical, sensory or mental
capabilities prevent them from using it safely. Children should be
supervised to ensure that they do not play with the appliance.
If young children, the aged or infirm are likely to be left in the vicinity
of the heater, we advise that adequate precautions should be taken.
We recommend that a guard be fitted to ensure contact with the
heater is avoided and objects cannot be inserted into the product.
If the mains lead is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person in
order to avoid a hazard.
For further information, please contact our guard supplier direct on
Tel. No. 01603 667957, or in case of difficulty or for further advice
contact the Customer Helpline.
Warning : In order to avoid a hazard due to inadvertent resetting of
the thermal cutout, this appliance must not be supplied through an
external switching device, such as a timer, or connected to a circuit
that is regularly switched on and off by the utility.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the voltage marked
on the heater must correspond to the supply voltage. If fitting a 13 amp
plug, a 13 amp fuse approved by ASTA to BS 1362 must be used. If any
other type of type of plug is used, a 15 amp fuse must be fitted in the plug,
the adaptor, or at the distribution board.
IMPORTANT - The wires in the mains lead are coloured in accordance
with the following code:
GREEN and YELLOW - EARTH
BLUE - NEUTRAL
BROWN - LIVE
Connect the GREEN AND YELLOW wire to the terminal marked ‘E’ or by
the earth symbol , or coloured GREEN or GREEN AND YELLOW.
Connect the BROWN wire to the terminal markef ‘L’ or coloured RED.
Connect the BLUE wire to the terminal marked ‘N’ or coloured BLACK.
This appliance must only be used on A.C. mains supply of 230/240
Volts~.
Wall Mounting
Three identical wall mounting brackets are secured to the base of the
heater with a fixing screw. To wall mount appliance, first remove the
brackets as follows :
Lay the heater on its back.
Following the sequence in Fig. 1 – identify and remove the fixing screw
securing the brackets located beside Mains Cable as shown in (A), then
pull out brackets and rotate them to disengage them from the slot (B).
Withdraw the brackets from the slot (C).
(A) (B) (C)
Fig. 1
Select a suitable position on a wall, near to a mains power socket,
making sure that there is at least 230 mm below the heater and at least
450 mm above the heater of unobstructed space. See also ‘Positioning
the heater’.
Fix the two top retaining brackets to the wall, using suitable fixings, for
2kw models at 358 mm centres and 3kw models at 478 mm centres –
see Fig 2.
Fig. 2
Locate the heater on the top brackets and allow it to hang in place.
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.
Loading ...
Loading ...
Loading ...