Loading ...
Loading ...
Loading ...
INSTALLATION
• Before installing the light fixture, ensure that all parts are present. Compare parts with the Hardware Included and Package
Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this light fixture.
• Turn off the power before installation,remove the old light fixture if necessary.Open the hole on the mounting surface according
to the size of fixture.
• When mounting fixture, for Dusk to Dawn operation, make sure the photocell orientation is at the top for wall mount, in an
area that receives daylight and not too close to reflective surfaces.
Estimated installation time: 20 minutes.
OPERATIONAL INSTRUCTIONS
Dusk-to-dawn operation enables the light fixture to automatically turn ON when dark outside and turn OFF when the sun rises,
thus saving you energy.
FIVE -YEAR LIMITED WARRANTY:
If, during normal use, this PATRIOT LIGHTING
®
lighting fixture breaks or fails
due to a defect in material and workmanship within five (5) year from the date of original purchase, simply bring this lighting
fixture with the original sales receipt back to your nearest MENARDS
®
retail store. At its discretion, PATRIOTLIGHTING
®
agrees to have the product or any defective part(s) repaired or replaced with the same or similar PATRIOTLIGHTING
®
product or part free of charge, within the stated warranty period, when returned by the original purchaser with original sales
receipt. This warranty; (1) excludes expendable parts including but not limited to light bulbs and batteries; (2) does not cover
damage that has resulted from abuse or misuse; and (3) does not cover any losses,labor, injuries to persons/property or costs.
This warranty does give you specific legal rights and you may have other rights, which vary from state to state.
TIP: To test if the light fixture and photocell works properly run power to the fixture and cover the photocell to turn fixture ON.
Shine a light into the photocell to see if fixture turns OFF.
Note: If photocell on the top of the light fixture is located in an area under heavy shade the photocell may not detect enough
light and may turn the light fixture on.
TROUBLESHOOTINGINSTALLATION AND OPERATION INSTRUCTIONS
1. Turn off the power and take
off the original light fixture.
2. Loosen the two mounting base
tightening screws using a philips
screwdriver. Then take apart the
fixture with a screwdriver. Pull the
handle of connect terminal to
vertically to pull off connect terminal.
Remove the lamp shade from the
light base.
3. Drill installation holes at the back
of the light with Dia.11/64 inch bit.
Measure the size of your junction
box to match the fixed screw hole
and mark the hole position to drill
out by power drill.
4. Set attached gasket (B) between
the light and the junction box. Pass
the wire from junction box through
the hole of Gasket (B) into the light
fixture.Then Making the electrical
connections using attached three
Wire Nuts (C).
5. Make sure the wire connection
polarity is correct.
* White to white
* Black to black
* Green ground to house ground
6. Fixing the light base on the
junction box at the wall by two
attached screws (D). Reattach
the lamp shade (F) to the light
base (E). Make sure the wire
connection polarity is correct.
* Red to red
* Black to black
7. Connect the quick connection
terminal. Then close the fixture by
tightening the two mounting base
tightening screws.
screw
8. Caulk around the mounting plate
and surface with silicone sealant
(not included).
Light stays ON
The light fixture is wired through an
unsuitable dimmer.
Light sensor is in a shaded area.
Replace the dimmer switch to a standard
ON/OFF wall switch.
Shine a flashlight into the light sensor and
wait a couple minutes. If the light turns OFF,
the fixture should be moved to a location
with enough light in the daylight hours for
the light sensor to work.
Light cycles ON and OFF
continuously
Photocell light sensor is sensing reflected
light.
Relocate light fixture to a location where
there is no reflected light.
Light FLICKERS
Problem Possible Cause Solution
Light does not
turn ON
No power to the fixture.
Check if circuit breaker is tripped and
confirm wall switch is ON.
Verify wiring to fixture is correct
(turn power off to fixture beforehand).
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 855-232-6423
Monday – Friday 8:00 a.m. – 8:00 p.m. (EST)
3 4