Elkay LZWSSM Installation and Use Manual

Loading ...

98764C (Rev. J - 08/17)

EZWSSM-1A, EZWSSMJO-2A, LZWSSM-1A, LZWSSMJO-2A

Page 4

Plumbing Connections

• Ensure lines and ports remain clean and free of contaminants during assembly.

• Purge each component if necessary.

• To ensure quick-connect connections seal properly, follow instructions per Figure 2, Page 2.

Connect Electrical Power:

1. For 120V Models: Plug Power Cord into wall outlet.

1.1. For 220V Models: Thread one end of Power Cord Plug through Bottom Cover and into Power inlet of Bottle Filler,

then plug other end of power cord into wall outlet. (See Fig. 4, Page 7.)

2. Conrm unit is on:

2.1. Filtered Units: Both the Filter Status Green LED and the Bottle Counter LCD on the Nameplate are illuminated.

2.2. Non-Filtered Units: The Bottle Counter LCD on the Nameplate is illuminated.

3. Ensure water dispenses: Activate unit by placing cup, hand or an opaque object in front of Sensor Lens and water

 shouldow.Itisnormalforthewaterstreamtosputterwithairwhentheunitisneworanewltercartridgeisinstalled.

4. Ensure a steady water ow is obtained: Activateunitperaboveandholduntilallairentrappedinlinesandlteris

purged. Since unit only dispenses water for 20 seconds per activation, multiple activations may be required.

5. Inspect for leaks and if any found, unplug unit and correct before continuing.

6. If setting up the Control Board for the rst time, go to Setting the Control Board (below) before continuing.

7. For 220V Models:PlaceCableClamp(supplied)onPowerCord(SeeFig.4,Page7)allowingsufcientslackfor

installing and removing Bottom Cover with cord plugged in and secure Clamp with Screw (supplied).

8. Place Bottom Cover in position on underside of unit with long tab against wall and slide up into Back Panel

opening. Secure with two supplied Allen head screws using a 5/32" hex-wrench (not supplied).

9. For 120V Models: For a clean appearance, gather and loop any extra Power Cord and secure to the underside of

bottom Cover with supplied adhesive backed clip.

Instruction for Use

1. To activate water ow, position mouth of water bottle or container under Dispensing Nozzle and in a continuous motion,

 swingandholdcontainerinfrontofSensorLens.Holduntilcontainerislledtoleveldesired.

2. To stop water ow, pull container away from Sensor Lens.

1. Connect water supply line to unit:

1.1. Filtered Units: Connect the 3/8" O.D. copper tube (supplied factory attached on the Filter Head inlet port) to the

3/8" Compression end of Service Stop Valve.

1.2. Non-ltered Units: Connect the 3/8"O.D. poly tube with Insulation to the 3/8" Compression end of Service Stop Valve.

2. Connect water supply line from Filter:

2.1. Filtered Units: Connect the quick-connect Reducing Union Adapter Fitting, located at end of 3/8"O.D.

poly tube with Insulation, to the ¼” O.D. poly tube (supplied factory attached on the Filter Head outlet port).

2.2. Non-ltered Units: No connections necessary.

3. Connect the 1-1/4"O.D. Drain Tray Outlet to the in-wall Drain Line using a Slip Joint Drain Union or

compression clamp (not supplied). Tighten all connections water tight.

4. Install new Filter Cartridge by removing its protective cap, inserting into Filter Head and rotating Filter Cartridge

clockwise until it bottoms-out into Filter Head.

5. Turn water supply on, inspect for leaks and correct any leaks before continuing.

Connect Plumbing Lines

Changing the Filter

1. Remove the Bottom Cover of the Bottle Filler by removing the two (2) screws.

2. Remove lter from head byrotatingltercounterclockwise.

3. Remove new lter from carton,removeprotectivecap;capmaybeplacedonanoldltertoreducethechanceofthe

 waterspillingfromlterhousing.

4. Attach lter to lter headbyrmlyinsertingintoheadandrotatinglterclockwise.

5. Activate sensor on Bottle Filleruntilapproximately1gallonofwaterisdispensed.Thisushingprocedurepurgesair

 andnecarbonparticlesfromthelter.

Loading ...

Elkay LZWSSM EZH2O Bottle Filling Station Surface Mount, Filtered Non-Refrigerated Stainless

Installation and Use Manual - Page 4