Loading ...
Loading ...
Loading ...
A choice of 1KW or 2KW heat output is provided by the fan
heaters which are concealed within the unit.
The heater can be used remotely or manually - see ‘Operation’.
General features of remote control are:
•Flame picture can be turned On or Off.
•Heat output can be increased or decreased according
to your particular requirements
Please Note: Used in an environment where background
noise is very low, it may be possible to hear the motor which
operates the ame effect. This is normal and should not be a
cause for concern.
Installation
Safety Message - Sufcient expertise is required for installing
this product. If unsure we recommend that you subcontract
the installation and pay special attention to safety during the
installation.
Wall Installation
Do not connect appliance until properly xed to the wall
and the Instruction leaet is fully read. In particular, the
minimum distances must be observed.
For installation of the appliance, care must be taken not to
damage concealed cables.
Please be careful while drilling the holes.
The wall plugs supplied with this product are for use with Block/
Brick built walls only.
This model is designed to be permanently xed to a wall at
a minimum height of 300mm. The wall bracket must be tted
horizontally and the cable routed to the bottom right of the
appliance shown as “a” in Fig. 1.
A height of 600 to 725mm from bottom of the appliance to oor
is recommended for optimum viewing of fuel bed (see Fig. 2
for recommended xing dimensions).
For optimum viewing mark the top four screw xing positions
on wall in accordance with the recommended xing dimensions
- see Fig. 2. Drill holes with a 6mm drill bit.
Fix the wall bracket using the plugs and screws provided - see
Fig. 3.
Carefully lift the appliance up ensuring that the top rear ledge
of the appliance engages the wall bracket and is centrally
positioned. - see Fig. 4.
A bottom xing bracket is supplied. Fix this bracket to the
bottom of the appliance using the silver screw on the underside.
With the bracket in place mark the location of the hole on the
wall. Then remove the appliance,drill the wall, t the wall plug
and re-t the appliance ensuring that you secure it in place by
screwing the bracket to the wall.
Recessed Installation
Please note that this appliance can also be recessed. This
can be installed in a large replace opening or a purpose built
wall. See Fig. 6 for size of recess required and hole xing
dimensions.
It is essential that this re is securly xed to the wall and it is
important that the xing device chosen is appropriate to the
wall material. Some modern internal building materials may
require specialised xing devices to provide a safe, secure
installation. If in doubt, please consult a qualied installer.
The wall should be capable of supporting the weight of the
appliance. If the installation of the bracket on the wall is not
sufciently sturdy, the unit may fall and cause injury or property
damage.
Existing Fireplace
1. Make sure that the re is located on a at surface.
2. Seal all draughts and vents to prevent chimney debris from
falling onto the appliance. Do not install into an existing
replace that is prone to dampness.
3. Remove the re front panel by following the steps as
outlined in ‘Front Panel Removal’ section.
4. Locate the 4 xing holes,2 top and 2 bottom, position the
re accordingly, and rmly x the appliance to the wall using
the appropriate screws - see Fig. 6.
5. Replace the front panel.
New Support Structure Construction
If planning to position your applaince on a purpose built support
structure the following steps must be observed:
1. Place the re in the desired location to see how it will look
in the room.
2. Mark the desired location for the new support structure in the
room and store the re in a safe, dry and dust free location.
3. Using timber studs to support the re, devise and construct
a suitable means of supporting the product within the wall
partition and provide electrical power for the re to be HARD
wired. For recommended sizes of height, width and depth of
opening for recess and hole xing dimensions - see Fig. 6
4. When the structure is complete, remove the front panel of
the re by following the steps as outlined in ‘Front Panel
Removal’ section.
5. Locate the 4 xing holes, position the re accordingly, and
rmly x using the appropriate screws.
6. Replace the front panel.
NOTE: The appliance should be HARD wired to an electrical
power outlet when placed in a recessed installation.
The heater is tted with a exible cable, size 3 x 1.0mm
2
for
connection to the xed wiring of the premises through a suitable
connection box positioned adjacent to the heater.
A means for disconnection must be incorporated in the xed
wiring of the premises in accordance with the wiring rules.
Please consult a qualied electrician for appropriate wiring
requirements.
Front Panel Removal
To remove the front panel please apply the following procedure:
While holding the front panel by its sides with both hands, (1)
carefully tilt the bottom of the frame outwards until free and
then lift the panel up (2) and then away (3) from the main
body - see Fig. 7.
Loading ...
Loading ...
Loading ...