User Manual Samsung DVG52M7750V/A3 Samsung 7.4 Cu. Ft. Capacity Gas Dryer

Press to adjust the dryness in the Sensor Dry and Steam Cycles. The corresponding indicator turns on.

• Larger or bulkier loads may require Very Dry or More Dry for complete dryness.
• Less Dry is best suited for lightweight fabrics or for leaving some moisture in the clothing at the end of the cycle.
• Damp Dry is designed to partially dry items. Use for items that lay flat or hang to dry.

NOTE: This option is not available with STEAM SANITIZE, and ACTIVE WEAR.

Press to change the temperature of the current cycle.

• High: For sturdy cottons or those labeled Tumble Dry.
• Medium: For permanent press, synthetics, lightweight cottons, or items labeled Tumble Dry Medium.
• Med Low: For heat lower than Medium. Use to dry synthetic or washable knit fabrics.
• Low: For heat sensitive items labeled Tumble Dry Low or Tumble Dry Warm.
• Extra Low: Provides the lowest heated drying temperature possible.

This function is available with NORMAL and TIME DRY. With the Eco Dry activated, drying takes a longer time but the power consumption is reduced.

The drying time can be extended by up to 3 times depending on the temperature and load. The Eco Dry function is enabled by default.

The Mixed Load Bell notifies you when the average dry level in a load is damp dry (80 % dried). This lets you take items that you don’t want fully dried or that dry quickly out of the dryer early while letting others continue to dry.

You can select this option in all Sensor Dry cycles except for STEAM SANITIZE, and ACTIVE WEAR. Available dry levels are Normal Dry, More Dry, and Very Dry.

Reduces static electricity that occurs from clothing friction. This is done by spraying steam in a later stage of the drying cycle.

NOTE: The Anti Static function is only available with NORMAL, HEAVY DUTY, PERM PRESS, DELICATES, and TIME DRY.

Wrinkle Prevent provides approximately 180 minutes of intermittent tumbling in unheated air at the end of the cycle to reduce wrinkling. Press Wrinkle Prevent to activate this feature.

The load is dry, and can be removed at any time during the Wrinkle Prevent cycle.

Press Sound to turn on or off the dryer’s notification beeps and melodies.

NOTE: This function remains active even after you restart the dryer

For most fabrics including cottons and linens.

If NORMAL is selected, the Eco Dry function is enabled by default. For more information, see Eco Dry in the “Feature panel“ section.

For exercise wear and outdoor wear such as sports jerseys, training pants, water-repellent jackets, and other performance clothing.

Thick fabrics like a zipper or velcro closure of a jacket, or training socks may not be completely dried

You can specify a cycle time in minutes.

If TIME DRY is selected, the Eco Dry function is enabled by default. For more information, see Eco Dry in the “Feature panel“ section.

Follow the care label instructions or dry using BEDDING.

• Make sure the item is thoroughly dry before using or storing.
• May require repositioning in the drum to ensure even drying.

Use NORMAL and dry only one blanket at a time for best tumbling action.

• Make sure blankets are is thoroughly dry before using or storing.

Use PERM PRESS and the Medium temperature setting to help minimize wrinkling.

• Dry curtains and draperies in small loads for best results and remove as soon as possible.

Use NORMAL and the Medium temperature setting.

• Add a couple of dry towels to absorb moisture and shorten drying time.

Do not dry on a heat setting. Use AIR FLUFF.

WARNING: Drying a rubber item with heat may damage it or cause a fire

Use NORMAL.

• Add a couple of dry towels and a pair of clean sneakers to help the tumbling action and to fluff the items.
• Do not dry kapok or foam pillows using a heated drying cycle.

You can dry these items in the dryer only if you use AIR FLUFF

• The duct or lint filter is clogged.
• The pressure applied to the duct is high because the duct is too long or bent.

• Check the lint filter or duct and clean if necessary.
• Check the duct connections and shorten or straighten the duct if necessary.

• The duct or lint filter is severely clogged.
• The pressure applied to the duct is very high because the duct is too long or bent.

• Check and clean the lint filter or duct and make sure they are not clogged.
• Check the duct connections and shorten or straighten the duct work.

• Make sure the door is latched shut.
• Make sure the power cord is plugged into a live electrical outlet.
• Check your home’s circuit breakers or fuses.
• Press or tap START/PAUSE again if the door is opened during a cycle.
• Clean the lint filter

• Check your home’s circuit breakers or fuses.
• Some cycles do not require heating. Check the selected cycle again.
• For a gas dryer, make sure the gas supply is on.
• Clean the lint filter and exhaust duct.
• The dryer may have moved into the cool-down phase of the cycle.

• Check all of the above, plus...
• Make sure the exhaust hood outside your home can open and close freely.
• Check the exhaust system for lint buildup. Ducting should be inspected and cleaned annually.
• Use a 4” rigid metal exhaust duct.
• Do not overload. 1 wash load = 1 dryer load.
• Dry heavy items and light weight items separately.
• Large, bulky items, such as blankets or comforters, may require repositioning to ensure even drying.
• Make sure that your washer is draining properly and extracting adequate water from the load.
• The load may be too small to tumble properly. Add a few towels and restart the dryer.
• The load may be too large to tumble properly. Remove some items and restart the dryer.
• Clean the lint filter.

• Check the load for objects such as coins, loose buttons, nails, etc. Remove promptly.
• It is normal to hear the dryer gas valve or heating element cycle on and off during the drying cycle.
• Make sure the dryer is leveled properly as outlined in the installation instructions.
• It is normal for the dryer to hum due to the high velocity of air moving through the dryer drum, fan, or exhaust system.

• Seams, pockets, and other similarly heavy areas may not be completely dry when the rest of the load has reached the selected dryness level. This is normal. You can choose a higher dryness level or a cycle that involves a higher dryness level.
• If one heavy item is dried with a light weight load, such as one towel with sheets, it is possible that the heavy item will not be completely dry when the rest of the load has reached the selected dryness level.
• For the best drying results, dry heavy items and light weight items separately.

• Household odors from paint, varnish, strong cleaners, etc. may enter the dryer with the surrounding room air. This is normal as the dryer draws the air from the room, heats it, pulls it through the tumbler, and exhausts it outside.
• When these odors linger in the air, completely ventilate the room before using the dryer.
• Use a cycle featuring the Refresh function. If odors persist, wash and dry the item again.

• Make sure the lint filter is cleaned before every load. For clothes that naturally build up lint, clean the filter during the cycle.
• Some fabrics are lint producers (for example, a fuzzy white cotton towel) and they must be dried separately from clothes that are lint trappers (for example, a pair of black linen pants).
• Divide larger loads into smaller loads for drying.
• Check pockets thoroughly before drying, then dry clothes.
• Remove lint inside the drum before drying.

• Small loads of 1 to 4 items work best.
• Load fewer items. Load similar-type items.
• Take out the items immediately after drying is complete.

• This is steam condensation. The dripping water will stop after a short time.

• Sprayed water is difficult to see when the door is closed.

• Sensor Dry automatically senses the moisture in the load and shuts the dryer off when the selected dryness level is reached. The drying time can change according to the type and amount of laundry. See the cycle chart for reference.

Operating the dryer with the door open.

• Make sure the door is properly closed.
• Make sure laundry is not caught in the door.

Invalid power source frequency

• Try restarting the cycle.
• If this information code remains, contact a Samsung customer service center.

Electronic control problem (Invalid Communication).

• Contact a Samsung a customer service center.

Malfunction is detected in the motor relay circuit.

• Contact a Samsung customer service center.

HC

HC4

High temperature heating check

• Clean the lint filter.
• If this information code remains, contact a Samsung customer HC4 service center.(enter the line test mode)

The electronic control needs to be checked.

• Check if power is supplied properly.
• If the information code remains, contact a customer service center.

The Thermistor1 resistance is very low or high.

• Check for a clogged lint screen
• Check if the vent system is restricted.
• If this information code remains, contact a Samsung customer service center.

The Thermistor2 resistance is very low or high.

• Check for a clogged lint screen.
• Check if the vent system is restricted.
• If this information code remains, contact a Samsung customer service center

Incorrect door switch.

• Contact a Samsung customer service center.