Loading ...
Loading ...
Loading ...
7
Settings
Individual settings for cycle minutes (Time), dryness level (Level) and temperature (Temp) can be set from the minimum
(lowest in column) to maximum (highest in column). In general, the higher up the column, the more energy will be used.
NOTE: The selected cycle set Time can be further adjusted, in one minute increments, by pressing the Time Adjust + (plus)
and - (minus) buttons.
Dryness Level-Selection only used for Sensor cycles. Timed cycles run for the selected time.
More Dry Use for heavy-duty or mixed type fabrics.
Dry Use for a normal dryness level suitable for most loads. This is the preferred cycle for energy savings.
Less Dry Use for lighter fabrics.
Damp
For leaving items partially damp.
Temperature
High For regular to heavy cottons.
NOTE: Steam Dewrinkle and Steam Refresh require the High temperature setting.
Medium For synthetics, blends, delicates and items labeled permanent press.
Low For delicates, synthetics and items labeled tumble dry low.
No Heat For fluffing items without heat. For use only with the Air Fluff cycle.
Extended Tumble
Use this option to minimize the wrinkles in clothes. It provides 1 hour of no-heat tumbling after the clothes are dry. If you are
using the cycle Signal Adjust or Volume and you select the Extended Tumble option, a signal will sound at the end of the
drying time and several times during the Extended Tumble cycle. This will remind you that it is time to remove the clothes.
Damp Alert
This option causes the dryer to beep when clothes have dried to a damp level. Remove items that you wish to hang dry. The
Damp Alert will only beep when this option is selected (but the dry cycle will keep running). Removing clothes and hanging them
when they are damp, can reduce the need to iron some items. The light beside the button will be lit when Damp Alert is on.
Drum Light
The drum light will turn on if the Damp Alert button is pressed for 3 seconds or the door is opened. It will turn off when
the door is shut, the Damp Alert button is pressed again for 3 seconds or after 5 minutes if the door is left open.
Delay Dry
Press the Delay Dry button to set the delay start time in 1 hour increments up to 24 hours, and then back to clear (0 hours).
After selecting the delay start time, press Start and the delay time will count down the time remaining until the cycle starts.
NOTE: To set the amount of delay time faster, you can press and hold the Delay Dry button.
Delay Dry for WiFi Connected Dryers
For more information see the Appliance Communication section.
You have two options to set Delay Dry using your smartphone.
Option 1: Follow Delay Dry instructions. You can use the GE Appliances Laundry App to adjust the amount of time via
your smartphone.
Option 2: Set your dryer to “AP” using the Delay Dry button. This allows you to use the GE Appliances Laundry App via
your smartphone to start your dryer remotely at the time of your choosing. If the dryer is set to AP with no activity, it will
start the dryer 24 hours later.
Signal Adjust or Volume (depending on model)
Use the Signal Adjust or Volume button to change the volume of the button presses and the end of cycle signal. Press the
button until you reach the desired volume or off. The clothes should be removed when the end of cycle signal goes off so
wrinkles do not set in.
NOTE:
• Remove garments promptly at the sound of signal. Place clothes on hangers so wrinkles will not set in.
• Use the Signal Adjust or Volume especially when drying fabrics like polyester, knits and permanent press. These fabrics
should be removed so wrinkles will not set in.
My Cycle
As the cycle selector knob is turned, the Time (timed dry), Level (dryness level) and Temp (temperature) settings change
to automatic pre-set default settings. If you desire a different setting, press the appropriate button(s). Then press and hold the
My Cycle button for 3 seconds and the dryer will “remember” these settings for that Knob Selection. In the future, when you turn
the selector knob to that cycle, your settings will be automatically recalled. NOTE: Signal volume cannot be set for My Cycle.
H
I
G
GEAppliances.com
Loading ...
Loading ...
Loading ...