Loading ...
Loading ...
Loading ...
EN
User manual
7
CLEAN+
Clean+ is an option working on 3 dierent levels (Intensive,
Daily and Fast) that are specially designed to set the right
washing action, depending on your cleaning needs:
Intensive : this option is designed for high levels of
dirtiness, removing most stubborn stains.
Daily : this option is designed to remove everyday stains.
Fast : this option is designed to remove lightly soiled
stains.
INTENSIVE RINSE
By selecting this option, the eciency of the rinse is
increased and optimal detergent removal is guaranteed. It is
particularly useful for sensitive skin. Press the button once,
two or three times to select an additional 1
+1
, 2
+2
or 3
+3
rinses after the standard cycle rinse and remove all traces of
detergent. Press the button again to go back to the “Normal
rinse” rinse type.
START DELAY
To set the selected programme to start at a later time, press
the button to set the desired delay time. The symbol
lights on the display when this fuction is enabled. To cancel
the delayed start, press the button again untile the value
‚‘‘0‘‘ is shown on the display.
ON/OFF
To switch on the washing machine: press the
“ON/OFF“ button, the “Start/Pause” button light up.
To switch o the washing machine during the wash cycle,
press and hold the button for approximately 3 seconds. If
the button is pressed briey or accidentally the machine will
not switch o.
To switch o the washing machine after programme end:
press the “ON/OFF“ button until the lights go o.
KNOB
To select and conrm programmes. Turn to
select.
START/PAUSE
To start the programme, after you have nished your
settings. To pause a running programme. To continue a
paused programme.
KEY LOCK
To lock the control panel, press and hold the
“Key lock” button for approximately 3 seconds. The
symbol will light up on the display to indicate that the
control panel has been locked (with the exception of the
“ON/OFF“ button). This prevents unintentional changes
to programmes, especially with children near the machine.
To unlock the control panel, press and hold the “Key lock”
button for approximately 3 seconds .
FUNCTIONS
OPTIONS
BLEACHING
If you wish to bleach the laundry, load the washing machine
and set the “Rinse & Spin” programme.
Start the machine and wait for it to complete the rst water
lling cycle (roughly 2 minutes). Put the machine in pause
mode by pressing the “Start/Pause” button, open
the detergent drawer and pour the bleach (observe the
recommended doses indicated on the package) into the
main wash compartment where the partition was previously
mounted. Restart the cycle by pressing the “Start/Pause”
button.
If desired, it is possible to add fabric softener into the
appropriate compartment of the detergent drawer.
DEMO MODE
This function is only used for sales presentations. By this
you can interact with washing machine and see it working
without water. To enter Demo mode, switch the washing
machine ON and OFF again. Press and hold “Start/Pause”
button, then within 5 seconds press also “ON/OFF“
button and hold both buttons for 10 seconds.
To deactivate this function, switch the washing machine
OFF. Than press and hold “Start/Pause” button, within
5 seconds press also “ON/OFF“ button and hold both
buttons for 2 seconds.
! If the selected function is incompatible with the set programme, the incompatibility will be signalled by a buzzer (3 beeps).
! If the selected function is incompatible with another previously set function the function will not be enabled.
FRESHCARE+
This option enhances washing performance by generating
steam to inhibit the proliferation of the main bad odour
sources inside the machine. After steam phase, the washing
machine will perform gentle tumbling through slow
rotations of the drum. FreshCare+ option starts after the
cycle ends for a maximum duration of 6h and you can
interrupt it at any time by pressing any button on control
panel or turning the knob. Wait around 5 minutes before
door can be opened.
TEMPERATURE
Every programme has a predened temperature. If you
want to change the temperature, press the “temperature”
button. The value appears on the display.
SPIN
Every programme has a predened spin speed. If you want
to change the spin speed, press the "Spin" button. The value
appears on the display.
Loading ...
Loading ...
Loading ...