Loading ...
Loading ...
Loading ...
ASSEMBLY
• Lie vacuum flat and attach vacuum head by sliding it on until it clicks.
• Stand vacuum up straight, attach wand to hose and push into place until it clicks.
• Attach tools to the side of the vacuum.
USING YOUR DYSON VACUUM
Press foot pedal and recline handle to use. The stabilizer stand will automatically lift up.
To switch ‘ON’, depress power button in front of handle. After cleaning, push
vacuum into an upright position and stabilizer wheels will automatically drop.
Use the cyclone carry handle to carry the vacuum.
CAUTION:
• Do not use or store this vacuum below 32°F (0°C). Ensure that the vacuum is at
room temperature before operating.
• Do not allow the vacuum to be used by anyone who may not be able to operate
it safely.
• The use of an extension cord is not recommended.
• Always switch off and unplug the vacuum before performing maintenance on
your vacuum.
• When returning to the upright position, ensure that the stabilizer wheels are fully
engaged before releasing the vacuum.
• Ensure the cyclone is secured to the vacuum. Do not press the cyclone release
button or shake the vacuum while carrying or it could fall and cause injury.
• Store the vacuum indoors. Put the vacuum away after use with the cord coiled
safely, to prevent tripping hazards.
• Do not use outdoors or on wet surfaces or to vacuum water or other liquids –
electric shock could occur.
• Check to ensure your electricity supply corresponds to that shown on the rating
plate, which can be found behind the clear bin. The vacuum must only be used
as rated.
• Do not lubricate any parts, or carry out any maintenance or repair work other
than that shown in this Dyson Operating Manual, or advised by the Dyson
Customer Care Helpline.
PLEASE NOTE:
• This vacuum is intended for domestic use only. Fine dust such as plaster dust or
flour should only be vacuumed in very small amounts.
• Do not use the vacuum to pick up sharp hard objects, small toys, pins, paper
clips, etc. They may damage the vacuum.
• Consult your flooring manufacturer’s recommended instructions before
vacuuming and caring for your flooring, rugs, and carpet. The brush bar on the
vacuum can damage certain carpet types and floors. If unsure turn brush bar off
in order to enable proper operation. Some carpets will fuzz if a rotating brush
bar is used when vacuuming. If this happens, we recommend vacuuming in bare
floors mode and consulting with your flooring manufacturer.
• When vacuuming, certain carpets may generate small static charges in the
clear bin or wand. These are entirely harmless and are not associated with the
electricity supply. To minimize any effect from this, do not put your hand or
insert any object into the clear bin unless you have first emptied it and rinsed it
out with cold water (see ‘clear bin cleaning` section).
• Do not use any lubricants, cleaning agents, polishes or air fresheners on any
part of the Dyson vacuum.
• This Dyson vacuum is fitted with a thermal cut-out. If any part of the Dyson
vacuum becomes blocked the machine may overheat and automatically shut
off. If this happens, switch off and unplug the Dyson vacuum and allow to cool
before attempting to check filters or for blockages. Clear any blockages
before restarting.
• Do not use this vacuum cleaner outdoors. The Dyson Car Cleaning Kit (Model
08909) is intended for use only inside a garage.
CARPETS OR HARD FLOORS
The brush bar will always default to ‘ON’ (spinning) each time you switch on
the vacuum and recline it for cleaning. The brush bar will automatically stop
if it becomes obstructed. If the brush bar stops during use, please refer to the
‘Clearing brush bar obstructions’ section.
To switch the brush bar off (e.g. for hard floors), recline the vacuum and turn it
‘ON’, then press the brush bar ‘ON/OFF’ button – the brush bar will
stop spinning.
HIGH REACH CLEANING
CAUTION:
• Switch ‘OFF’ vacuum before changing tools.
• Powerful suction can cause the hose to ‘pull back’ - please take care.
• Take extra care when vacuuming on stairs; do not work with the vacuum above
you on the stairs. Do not put the vacuum on chairs, tables etc.
• Ensure vacuum is in upright position before using tools.
PLEASE NOTE:
• To release the wand, press button and lift up. Rotate the wand, open the wand
cap and clip handle into hose. Tools can be attached to either the hose or wand.
• The brush bar will not rotate when the vacuum is in an upright position.
• Ensure wand cap is closed when not in use.
CLEAR BIN EMPTYING
CAUTION:
• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
To remove the clear bin from the vacuum press the button at rear of cyclone
carrying handle. To release the dirt, press the red clear bin release button.
• Switch ‘OFF’ vacuum and unplug the vacuum before emptying the clear bin.
PLEASE NOTE:
• Do not use the vacuum without the clear bin in place.
• To minimize dust/allergen contact when emptying, encase base of bin tightly
in a plastic bag before trigger releases dirt. Remove bin carefully and seal bag
tightly; dispose as normal.
CLEAR BIN CLEANING
CAUTION:
• Do not immerse the whole cyclone in water or pour water into the cyclones.
• Ensure the clear bin is completely dry before replacing.
PLEASE NOTE:
• Do not use detergents, polishes or air fresheners to clean the clear bin.
• Clean the shroud with a cloth or dry brush to remove lint and dust.
• Do not put clear bin in a dishwasher.
WASHING YOUR FILTERS
CAUTION:
• Switch ‘OFF’ and unplug the vacuum before removing the filters.
• Ensure filters are completely dry before refitting into the vacuum.
PLEASE NOTE:
• This vacuum has two filters, located as shown. It is important to check your filters
regularly and wash at least every month according to instructions,
to maintain performance.
• The filter in the ball should be rinsed and tapped out until the water runs clean,
then tapped out again to ensure all excess water is removed. Please leave to dry
completely for 24 hours.
• It is normal for this filter in the ball to turn grey in color. The filters may require
more frequent washing if vacuuming fine dust.
• Do not use detergents to clean the filters.
• Do not put the filters in a dishwasher, washing machine, tumble dryer, oven,
microwave or near an open flame.
LOOKING FOR BLOCKAGES
CAUTION:
• Switch ‘OFF’ and unplug the vacuum before checking for blockages. Failure to
do so could result in personal injury.
• Please ensure vacuum is upright and switched off before removing hose or
airway inspection parts.
• Beware of sharp objects when clearing blockages.
• Refit all parts of the vacuum securely before using.
PLEASE NOTE:
• Clearing blockages is not covered by your vacuum’s limited warranty. This
vacuum is fitted with a thermal cut-out. If any part of your vacuum becomes
blocked, it may overheat and then automatically shut off. Switch ‘OFF’ and
unplug the vacuum and leave to cool down for at least 60 minutes before
attempting to check filters or for blockages. Clear blockage before restarting.
CLEARING BRUSH BAR OBSTRUCTIONS
CAUTION:
• Switch off and unplug the vacuum before clearing brush bar obstructions.
Failure to do so could result in personal injury.
• If your brush bar is obstructed, it may shut off. If this happens you will need to
remove the brush bar as shown and clear any obstructing debris. Beware of
sharp objects when clearing obstructions.
PLEASE NOTE:
• Cleaning the brush bar obstructions is not covered by your vacuum’s
limited warranty.
DISPOSAL INFORMATION
Dyson products are made from high grade recyclable materials. Please dispose
of this product responsibly and recycle where possible.
8
Loading ...
Loading ...
Loading ...