WARNING: Water in the dishwasher may be hot. Danger of scalding! Only open the door during operation if absolutely necessary and exercise extreme caution when doing so.
WARNING: Danger of crushing injuries! Do not put your hand inside the door as it is closing.
Rinse aid is needed to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed.
WARNING: Filling the rinse aid reservoir with detergent will damage the reservoir. Only pour rinse aid formulated for residential dishwashers into the reservoir. When using “Tab” detergents rinse aid is not needed.
Adding rinse aid
The rinse aid reservoir holds approx. 3.7 oz. (110 ml).
Rinse aid indicator
When the Rinse aid indicator lights up, the rinse aid reservoir contains sufficient rinse aid for 2 - 3 programs only
If you consistently use a “Tab” detergent, you can deactivate the refill indicators if you wish (see “Options - Refill indicators”).
Setting the rinse aid dosage
You can adjust the rinse aid dosage for best results.
The rinse aid dosage is set in stages from 0 to 6. It is set to 3 at the factory. This is the recommended setting.
The rinse aid dosage can turn out to be higher than the set value due to the automatic adjustment of the program.
If spots appear on dishware and glassware:
If clouding or smearing appears on dishware and glassware:
button, if it is turned on.
, and, simultaneously switch the dishwasher on using the button. Keep the program selection button pressed in for at least four seconds until the lower right program indicator light comes on.If this does not happen, start the procedure from the beginning again.
button three times.The indicator light will flash 3 times at short intervals.
The set value will appear in the display after 
.
The flashing sequence 
will appear in the display.
This indicates a factory default setting of 3.
to select the setting required. Each press of the button moves you up a stage.The setting is now saved.
button.Remove coarse food residues from the dishes.
There is no need to rinse items under running water
WARNING: Do not wash items soiled with ash, sand, wax, grease, or paint in the dishwasher. These will damage the dishwasher. Some foods may contain natural dyes, e.g., carrots, tomatoes or tomato sauce. Plastic items in the dishwasher may discolor if large quantities of these foodstuffs find their way into the dishwasher on the dishes. The stability of plastic items is not affected by this discoloration. Cleaning silver cutlery in the dishwasher may also cause plastic items to discolor.
Dishes can be loaded anywhere in the baskets, but the following notes should be observed:
Items not recommended for dishwashing
Please note:
Silverware previously cleaned with a silver polish may still be damp or spotted at the end of a program, where water has not run off smoothly. It may need to be rubbed dry with a soft cloth.
Silver which has been in contact with foods containing sulphur can discolor. These include egg yolk, onions, mayonnaise, mustard, fish, and marinades.
WARNING: Aluminum components (e.g., range hood grease filters) must not be cleaned with a commercial or industrial cleaning agent. These may damage the material.
Tip: When purchasing new dishes and cutlery, make sure they are dishwasher-safe.
Glass care
Loading for 10 standard place settings with cutlery tray
Upper basket
Lower basket
Cutlery tray (depending on model)
Loading for 16 standard place settings with cutlery tray
Upper basket
Lower basket
Cutlery tray (depending on model)
Loading for 10 standard place settings with cutlery basket
Upper basket
Lower basket
Cutlery basket
Loading for 13 standard place settings with cutlery basket
Upper basket
Lower basket
Cutlery basket
WARNING: For safety reasons, do not operate the dishwasher without the upper and lower baskets in place (except when running the Tall items program, if available).
Adjustable cup rack (depending on model)
Glasses can be arranged along the positioning rail of the cup rack to give them some support during the program.
Adjusting the upper basket
In order to gain more space for taller items the upper basket can be adjusted on three levels with 3/4" (2 cm) between each level.
The upper basket can also be set at an angle with one side high and the other side low. Make sure, however, that the basket can slide smoothly in and out of the cabinet.
Pull the upper basket out.
To raise the upper basket:
To lower the upper basket:
Depending on the setting of the upper basket, the following plate dimensions can be accommodated.
Dishwashers with cutlery basket
| Upper basket adjustment | Plate  in inches (cm) | ||
| Upper basket | Lower basket | ||
| ADA | Full-size | ||
| Upper | 7 7/8" (20) | 9 7/16" (24) | 12 3/16" (31) 13 3/4" (35*) |
| Middle | 8 11/16" (22) | 10 1/4" (26) | 11 7/16" (29) |
| Lower | 9 7/16" (24) | 11" (28) | 10 5/8" (27) |
Dishwashers with cutlery tray
| Upper basket adjustment | Plate in inches (cm) | ||
| Upper basket | Lower basket | ||
| ADA | Full-size | ||
| Upper | 7 7/8" (15) | 7 1/2" (19) | 12 3/16" (31) 13 3/4" (35*) |
| Middle | 6 11/16" (17) | 8 1/4" (21) | 11 7/16" (29) |
| Lower | 7 1/2" (19) | 9 1/16" (23) | 10 5/8" (27) |
* When tilted, plates of up to 13 3/4“ (35 cm) can be accommodated.
Depending on the setting of the upper basket, a variety of plate dimensions can be accommodated.
Glasses, cups and small items such as saucers can also be placed in the lower basket. Do not place thin, delicate glassware in the lower basket.
When tilted, plates up to 13 3/4" (35 cm) in diameter can be accommodated.
MultiComfort area
The rear section of the lower basket is used for washing cups, glasses, plates, pots and pans.
Hinged spikes
The spikes at the front are used for washing plates, soup bowls, platters, dessert bowls, and saucers.
The spikes can be lowered to make more room for large items, e.g. pots, pans, and bowls.
3D cutlery tray (depending on model)
To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.
Spoon heads should be placed in contact with at least one of the serrated retainers on the base of the cutlery tray to ensure that water runs off them freely.
The upper spray arm must not be blocked by items which are too big.
The side sections of the tray can be moved into the middle to accommodate tall items of dishware in the upper basket.
If spoon handles do not fit between the holders, lay them the other way round.
You can use the yellow slide to adjust the height of the middle section of the cutlery tray to make more room for large items of cutlery, such as serving spoons and ladles.
Cutlery basket (depending on model)
The cutlery basket can be placed anywhere on the front rows of spikes in the lower basket.
Cutlery insert for the cutlery basket
Use the insert supplied for heavily soiled items of cutlery. The insert separates the items so that they can be more easily accessed by water.
WARNING: Only use detergents formulated for domestic dishwashers.
Refer to the manufacturer's packaging as to whether Tab products are suitable for the water hardness level in your area.
Please note that the cleaning and drying results of Tab detergents can vary greatly.
For optimum cleaning and drying results, use Miele dishwasher detergent and add Miele salt and Miele rinse aid separately.
Detergent dosage
Use only the recommended amount of detergent. Continued use of too much detergent may cause machine damage.
WARNING: Dishwasher detergents can cause burning in the nose, mouth, and throat if swallowed, or inhibit breathing.
Avoid inhaling or swallowing dishwasher detergent. Keep children away from detergent. Keep detergent out of the reach of children. Keep children away from the dishwasher when the door is open. There could still be detergent residues in the dishwasher. Only add detergent just before starting the program and lock the door with the child safety lock (depending on model).
Adding detergent
Press the opening catch on the detergent dispenser. The flap will spring open.
The flap is always open at the end of a program.
Add the required amount of detergent and close the flap.
Make sure that the detergent packaging is properly closed after use to avoid it getting damp and becoming lumpy.
Dispensing aid
Compartment I holds a maximum of 2 teaspoons (10 ml), Compartment II holds a maximum of 3 ½ tablespoons (50 ml) of detergent.
The marks in compartment II indicate the levels of approximately 1 ¼ and 2 tablespoons (20 and 30 ml) respectively. The marks indicate the approximate fill level in ml when the door is open in a horizontal position.
button.The indicator light next to the program selected will come on.
Choose your program according to the type of load and the degree of soiling.
The different programs and their uses are described in the Program Overview chapter.
Use the program selection button 
to select the program required.
The indicator light for the program selected will light up.
The program duration will appear in hours and minutes in the display.
You can now select program options (see “Options”).
If any program options are selected, the appropriate indicator lights will also light up.
Start the program by closing the door within four seconds of the last press of a button.
The program will begin.
If you do not close the door within four seconds, the indicator lights of the selected program and the time display will flash.
The program cannot be started until you press the program selection button and close the door within four seconds.
A program should only be canceled in the first few minutes, if at all. Otherwise important program stages could be omitted.
The duration of the program selected appears in hours and minutes in the display before the program begins. During the program, the time left until the end of the program can only be viewed when the door is open.
The program duration displayed may vary with the same program. It is influenced by, among other things, the water temperature at each intake, the reactivation process, the softener assembly, the type of detergent, the amount of dishes, and the amount of soiling.
When a program is selected for the first time, the display will show the average program duration for a cold water intake.
The times shown in the program overview refer to standard test loads and temperatures.
Each time a program is run, the electronic module calculates the program duration required depending on the temperature of the water taken into the dishwasher and the amount of dishes.
To save energy, the dishwasher will switch off automatically 10 minutes after the last time a button has been pressed or 10 minutes after the end of the program.
Press the 
button to switch the dishwasher back on.
The dishwasher will not turn off while a program is running, during the delay start period, or if there is a fault.
A buzzer will sound at the end of the program with the door closed.
Open the door.
will appear in the time display.
If the program indicator light is still flashing, the program is not yet finished. Close the door again so that the program can continue until it has finished.
The drying fan may continue to run for a few minutes at the end of the program.
You can now empty the dishwasher.
WARNING: To prevent the risk of steam damage to the counter edging above the dishwasher, it is advisable to leave the door closed until you are ready to unload the dishware. Alternatively you can open the door fully until the dishware is cool enough to unload. Do not leave the door only partially open.
At the end of a program:
button.Switching the dishwasher off during a program stops the program.
Turning the dishwasher off during the delay start time will also stop the process.
If the dishwasher is not going to be used for a longer period of time, e.g., while on vacation, the water supply should be turned off.
Dishes tend to break and chip more easily when they are hot. Allow the dishes to cool until they are comfortable enough to handle before unloading them.
The dishes will cool much faster if you open the door when the program has ended.
First unload the lower basket, then the upper basket, and finally the cutlery tray (depending on model). This will prevent water drops from the upper basket and cutlery tray from falling onto the dishes in the lower basket.
A program will be interrupted as soon as the door is opened.
Close the door and press the Start button.
The program will continue from the point at which it was interrupted.
WARNING: Water in the dishwasher may be hot. Danger of scalding! Only open the door if absolutely necessary and exercise extreme caution when doing so. Before closing the door again, leave it ajar for approx. 20 seconds. This will enable the temperature in the wash cabinet to settle. After that, close the door and press the Start button.
If the detergent dispenser flap has already opened, do not change the program.
If a program has already started and you wish to change it, proceed as follows:
button. button.
The Short option reduces the duration of programs in which this option is available.
In order to achieve optimum cleaning results, consumption rates are increased with this option.
button. button. The indicator light will light up.The option selected will remain active for that particular program until the setting is changed.
If you consistently use a Tab detergent, you can deactivate the refill indicator if you wish.
button, if it is turned on.
, and, simultaneously switch the dishwasher on using the button. Keep the program selection button 
pressed in for at least four seconds until the lower right program indicator light comes on.If this does not happen, start the procedure from the beginning again.
button 9 times.The indicator light will flash 9 times at short intervals.
The flashing sequence in the time display will indicate whether the refill indicator is switched on or off.
– 
: Refill indicator is turned on.
– 
: Refill indicator is turned off.
to change the setting.The setting is now stored in memory.
button.If you switch to using detergent that does not contain salt or rinse aid, it is important to remember to add dishwasher salt and rinse aid and to turn the indicators back on.
Delay Start
You can set the start time for a program, e.g., to take advantage of night time electricity rates. The start time can be delayed between 30 minutes and 24 hours.
The delay period is shown in 30 minutes increments for a delay period between 30 minutes and 9 hours 30 minutes. It is shown in hours for periods longer than this.
When using the Delay Start function, make sure that the detergent compartment is dry before adding detergent. Wipe dry with a cloth if necessary. If the compartment is wet, powder detergent can become lumpy and stick to the dispenser, with the result that it is not fully dispensed. Do not use liquid detergent when selecting Delay Start, as it can run into the dishwasher before it is required.
button.
button.The last delay start time used will appear in the time display. The indicator light will light up.
button.If you keep the button pressed, the time will increase automatically up to 
hours. To get back to 
hours, press the button twice.
The time up until the program starts will count down in the display in hours for durations above 10 hours, and in minutes for durations below 10 hours.
When the set time is reached, the program selected will start automatically. The time remaining will appear in the time display and the indicator light will go out.
How the Delay Start time is shown in the display:
up to 59 minutes: e.g., 30 minutes = 
1 hour up to 9 hours 30 minutes: e.g., 5 hours = 
over 10 hours: e.g., 15 hours = 
Starting a program before the delay start time has elapsed:
A program can be started before the delay start period has elapsed. Proceed as follows:
button. button.A sequence of audible tones will sound at the end of the program or if there is a fault.
The buzzer at the end of a program and the warning buzzer in the event of a fault will sound 4 times at intervals with a short pause between each set.
The buzzer tones are activated at the factory.
You can deactivate the buzzer that sounds at the end of a program if you wish. The warning buzzer for faults cannot be deactivated.
button, if it is turned on.
, and, simultaneously switch the dishwasher on using the button. Keep the program selection button pressed in for at least four seconds until the lower right program indicator light comes on.If this does not happen, start the procedure from the beginning again.
button 4 times.The indicator light will flash 4 times at short intervals.
The flashing sequence in the time display shows whether the buzzers at the end of the program are activated or deactivated.
– : Buzzer tones activated
– : Buzzer tones deactivated
to change the setting.The setting is now stored in memory.
button.“Optimize Standby” is activated by default.
To save energy, the dishwasher will switch off automatically a few minutes after the last time a button has been pressed or after the end of a program.
The dishwasher will not turn off while a program is running, during the delay start period, or if there is a fault.
Optimize Standby can be switched off if you prefer. If you do this the duration before the dishwasher switches off automatically increases to 6 hours. Doing this will increase energy consumption.
button, if it is turned on., and, simultaneously switch the dishwasher on using the button. Keep the program selection button pressed in for at least four seconds until the lower right program indicator light comes on.If this does not happen, start the procedure from the beginning again.
button 8 times.The indicator light will flash 8 times at short intervals.
The flashing sequence in the time display shows whether or not Optimize Standby is activated.
– : “Optimize Standby” activated
– : “Optimize Standby” deactivated
to change the setting.The setting is now stored in memory.
button.If you have altered any settings from the factory default, you can reset them back to the factory default settings as follows:
button, if it is turned on., and, simultaneously switch the dishwasher on using the button. Keep the program selection button pressed in for at least four seconds until the lower right program indicator light comes on.If this does not happen, start the procedure from the beginning again.
button 19 times.The indicator light will flash once at a long interval and then 9 times at short intervals.
The flashing sequence in the display indicates whether a setting has been changed from its factory default.
– : All settings are set to factory default settings
– : At least one setting has been changed
.The setting is now stored in memory
button.Check and clean your dishwasher regularly. This will help avoid problems and faults.
WARNING: All surfaces are susceptible to scratching. Contact with unsuitable cleaning agents can alter or discolor all surfaces.
Generally, the wash cabinet is self cleaning if the correct amount of detergent is used.
If, however, there are limescale or grease deposits in the wash cabinet, these can be removed with a special cleaning agent (available from Miele). Follow the instructions on the packaging.
If you mainly use low temperature programs (< 120°F/50 °C), there is a risk of bacteria and unpleasant odors building up in the wash cabinet. To prevent this happening the dishwasher will automatically increase the temperature in the final rinse of the selected program after several programs using low temperatures have been run.
Bacteria could build up on the door seal and the sides of the dishwasher door as these surfaces are outside the wash cabinet and are not accessed and cleaned by the spray arm jets.
WARNING: If soiling remains longer, it may happen that the surfaces can become discolored or changed. Remove any soiling immediately.
To better maintain your appliance avoid the following:
The filter system in the base of the wash cabinet prevents food from being redeposited on dishes. It also protects the circulation pump from damage caused by foreign objects.
WARNING: This dishwasher must not be used without all the filters in place!
Collection of coarse soil may cause the filters to clog. The level of soiling and time it takes before the filters need cleaning will vary depending on use.
WARNING: Ensure that coarse soil does not get into the circulation system and cause a blockage.
To clean the inside of the filter, the flap must be opened:
WARNING: Take care when you are fitting the filter system that it is secured in position correctly. Otherwise coarse soil could get into the circulation system and cause a blockage.
Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months).
Remove the spray arms as follows:
| Problem | Possible cause and solution |
| The dishwasher does not start. | The door is not properly closed. - Push the door firmly shut. |
The dishwasher is not plugged in. - Insert the plug. | |
The circuit breaker has tripped. - Reset the fuse (see data plate for the correct fuse rating). | |
The dishwasher is not switched on. - Turn the dishwasher on with the | |
| The dishwasher stops during a program. | The circuit breaker has tripped. - Reset the fuse (see data plate for the correct fuse rating). - If the circuit breaker trips again, contact Miele Service. |
The warning buzzer is sounding. All the program indicator lights flash when the door is opened. Fault code  appears in the time display | There may be a technical fault. - Turn the dishwasher off with the - Turn the dishwasher back on after a few seconds. - Select the desired program. - Close the door. If the indicator lights flash again, there is a technical fault. - Contact Miele Service. |
Fault  : The drain pump is still running, even with the door open. | The WaterProof System has reacted. - Turn off the water supply. - Contact Miele Service. |
Fault  : | A fault has occurred in the circulation pump. - Turn the dishwasher off for at least 30 seconds with the - Turn the dishwasher back on. - Select the desired program. - Close the door. If the fault message appears again, there is a technical fault. - Contact Miele Service. |
| The dishwasher stopped working shortly after the program started. The warning buzzer is sounding. The Intake/Drain indicator light is flashing on and off. | The water supply is turned off. - Turn on the water supply all the way |
The dishwasher stops during a program. The warning buzzer is sounding. The Intake/Drain indicator light flashes. Fault code  or  appears in the time display. | Before fixing the fault: - Turn the dishwasher off with the |
There is a problem with the water intake. - Turn on the water supply fully and start the program again. - Clean the water intake filter. - The flow pressure at the connection point is lower than 7.25 psi. Contact a plumber |
| Problem | Possible cause and solution |
The dishwasher stops during a program. The warning buzzer is sounding. The Intake/Drain indicator light flashes. Fault code  appears in the time display | Before fixing the fault: - Turn the dishwasher off with the |
There is a problem with the water intake. There might be water in the wash cabinet. - Clean the filter system - Clean the drain pump - Clean the non-return valve - Remove any kink or loop in the drain hose. | |
| The warning buzzer is sounding. The indicator light of the selected program and the time display flash. The dishwasher does not start or the delay start time stops running. | The safe mode of the dishwasher was activated. The following takes place: – If you do not close the door within four seconds of the last press of a button at program start – If the door is open for longer than four seconds during a program or within the delay start time. - Press the program selection button and close the door within four seconds. |
| Detergent residue is left in the dispenser at the end of a program. | The dispenser was still damp when detergent was added. - Make sure the dispenser is dry before adding detergent. |
| The dispenser cover cannot be closed. | Detergent residue is blocking the latch. - Remove the detergent residue. |
| The inside of the door and/or the interior walls are wet after a program has finished. | This is caused by the drying system and does not indicate a fault. The moisture will dissipate after a while. |
| Water remains in the wash cabinet at the end of a program. | Before fixing the fault: - Turn the dishwasher off with the |
The filter system in the wash cabinet is clogged. - Clean the filter system | |
The drain pump or non-return valve is blocked. - Clean the drain pump or the non-return valve | |
The drain hose is kinked. - Remove the kink. |
| Problem | Possible cause and solution |
| There is a knocking noise in the wash cabinet. | A spray arm is hitting the dishes. - Interrupt the program, and rearrange the items which are obstructing the spray arm. |
| There is a rattling noise in the wash cabinet. | Dishes is moving around in the wash cabinet. - Interrupt the program and rearrange loose pieces. |
A foreign object (e.g., a cherry pit) has become lodged in the drain pump. - Remove the foreign object from the drain pump (see “Maintenance - Cleaning the drain pump and non-return valve”). | |
| There is a knocking noise from the water pipe | This may be caused by the installation or the diameter of the water pipe. - This has no influence on dishwasher function. If in doubt, contact a suitably qualified plumber. |
| Problem | Possible cause and solution |
| The dishes are not clean. | The dishes were not loaded correctly. - See notes in “Loading the dishwasher”. |
The program was not powerful enough. - Select a more intensive program | |
There is some stubborn soiling even though most of the dishware is only lightly soiled (e.g., with tea stains). - Select the “Adjust Automatic” program option | |
Not enough detergent was dispensed. - Use more detergent, or change your detergent. | |
Items are blocking the path of the spray arms. - Rearrange the items so that the spray arms can rotate freely. | |
The filter system in the base of the wash cabinet is not clean or is not correctly fitted. This may cause the spray arm jets to get blocked. - Clean and/or fit the filter system correctly. - Clean the spray arm jets if necessary | |
The non-return valve is open and blocked. Dirty water has flowed back into the wash cabinet. - Clean the drain pump and the non-return valve | |
| Smearing appears on glassware and cutlery. There is a bluish sheen on the surface of glassware; film can be wiped off. | The rinse aid dosage is set too high. - Reduce the dosage |
| Dishes is not dry or cutlery and glasses are spotty. | The rinse aid dosage is set too low or the rinse aid reservoir is empty. - Replenish the reservoir, increase the dosage, or change the brand of rinse aid |
Dishes was taken out of the cabinet too soon. - Leave it in for longer | |
Combination tabs have been used which have impaired drying performance. - Change your detergent, or replenish the rinse aid | |
| Glasses have a brownish-blue discoloration; the deposit cannot be wiped off. | Detergent deposits. - Switch to another detergent. |
| Glasses are dull and discolored; the deposit cannot be wiped off. | The glassware is not dishwasher-safe. The surfaces are affected. - There is no remedy. Purchase glassware which is dishwasher-safe. |
| Tea or lipstick stains have not been completely removed. | The wash temperature of the selected program was too low. - Select a program with a higher wash temperature. |
The bleaching effect of the detergent is too low. - Switch to another detergent. | |
| Plastic parts are discolored. | Natural dyes, e.g., from carrots, tomatoes, or ketchup may be the cause. The amount of detergent used or its bleaching effect was not sufficient to deal with natural dyes. - Use more detergent Discoloration is irreversible. |
| White residue is visible on dishes and cutlery, clouding occurs on glassware; this film can be wiped off. | The rinse aid dosage is too low. - Increase the dosage |
An unsuitable Tab detergent has been used. - Change your detergent. | |
| There are rust stains on the cutlery | The affected items are not corrosion resistant. - There is no remedy. Purchase cutlery which is dishwasher-safe. |
If the water has not been pumped away at the end of a program, the drain pump or the non-return valve might be blocked. They are, however, easy to clean.
The drain pump is located underneath the non-return valve (see arrow).
WARNING:
Reference file: Miele G 4998 SCVi SF AM Fully-integrated, Full-size Dishwasher
Additionally, the document applies to other Miele models: G 4993
button.