Loading ...
Loading ...
Loading ...
English - 12 -
Switching On/Off
To Switch the TV On
Connect the power cord to a power source such
as a wall socket (220-240V AC, 50 Hz).
To switch on the TV from standby mode either:
• Press the Standby button, Programme +/- or
a numeric button on the remote control.
• Press the side function switch on the TV until
the TV comes on from standby.
To Switch the TV Off
Press the Standby button on the remote control
or press the side function switch on the TV until
the TV switches into standby mode.
To power down the TV completely, unplug the
power cord from the mains socket.
Note: When the TV is switched into standby mode, the
standby LED can blink to indicate that features such as
Standby Search, Over Air Download or Timer is active.
The LED can also blink when you switch on the TV from
standby mode.
First Time Installation
When turned on for the rst time, the language
selection screen is displayed. Select the desired
language and press OK.
On the next screen, set your preferences using
the directional buttons.
Note: Depending on the Country selection you may be
asked to set and conrm a PIN at this point. The selected
PIN cannot be 0000. You have to enter it if you are asked
to enter a PIN for any menu operation later.
About Selecting Broadcast Type
Digital Aerial: If Digital Aerial broadcast search
option is turned on, the TV will search for digital
terrestrial broadcasts after other initial settings
are completed.
Digital Cable: If Digital Cable broadcast search
option is turned on, the TV will search for digital
cable broadcasts after other initial settings are
completed. According to your other preferences
a conrmation message may be displayed before
starting to search. Select YES and press OK to
proceed. To cancel operation, select NO and
press OK. You can select Network or set values
such as Frequency, Network ID and Search
Step. When nished, press OK button.
Note: Searching duration will change depending on the
selected Search Step.
Satellite(**): If Satellite broadcast search
option is turned on, the TV will search for digital
satellite broadcasts after other initial settings are
completed. Before satellite search is performed
some settings should be made. Antenna Type
menu will be displayed first. You can select
Antenna Type as Direct, Single Satellite Cable
or DiSEqC switch by using “ ” or “ ” buttons.
• Direct: If you have a single receiver and a direct
satellite dish, select this antenna type. Press OK
to continue. Select an available satellite on the
next screen and press OK to scan for services.
• Single Satellite Cable: If you have multiple
receivers and a single satellite cable system,
select this antenna type. Press OK to continue.
Congure settings by following instructions on
the next screen. Press OK to scan for services.
• DiSEqC switch: If you have multiple satellite
dishes and a DiSEqC switch, select this
antenna type. Press OK to continue. You can
set four DiSEqC options (if available) on the
next screen. Press OK button to scan the rst
satellite in the list.
Analogue: If Analogue broadcast search
option is turned on, the TV will search for
analogue broadcasts after other initial settings
are completed.
Additionally you can set a broadcast type as your
favourite one. Priority will be given to the selected
broadcast type during the search process and
the channels of it will be listed on the top of
the Channel List. When nished, press OK to
continue.
You can activate Store Mode option at this point.
This option will congure your TV’s settings for
store environment and depending on the TV
model being used, the supported features of it
may be displayed on the top of the screen as
an info banner. This option is intended only for
store use. It is recommended to select Home
Mode for home use. This option will be available
in System>Settings>More menu and can be
turned off/on later.
Press OK button on the remote control to
continue.After the initial settings are completed
TV will start to search for available broadcasts
of the selected broadcast types.
After all the available stations are stored, scan
results will be displayed. Press OK to continue.
The Edit Channel List menu will be displayed
Loading ...
Loading ...
Loading ...