Loading ...
GB
Quick Guide
THANK YOU FOR PURCHASING A HOTPOINT PRODUCT.
To receive more comprehensive assistance, register the
appliance on
www.hotpoint.eu/register
Before using the appliance carefully read the Health and Safety guide.
Before using the machine, it is imperative that the transport bolts are removed. For more
detailed instructions on how to remove them, see the Installation Guide.
CONTROL PANEL
1. ON/OFF button
2. DRYING button
3. DRY ONLY button
4. MULTI RINSE button
5. OPTION button
6. DIRECT INJECTION button
7. START/PAUSE button and indicator light
8. KEY LOCK button
9. DELAY button
10. SPIN button
11. TEMPERATURE button
12. AUTO CLEAN button
13. WASH CYCLE SELECTOR KNOB
14. Programme Key
WASH CYCLE TABLE
For all testing institutes:
2) Long cotton cycle: set programme 8 at temperature 40°C and press the DIRECT INJECTION
button under “Power” mode.
3) Long synthetics cycle: set cycle 9 at a temperature of 40°C.
* By selecting the cycle and excluding the spin cycle, the washer-dryer will drain only.
** If a drying cycle is also programmed, the machine will run a “wash+dry” programme lasting
45’ and a 1kg laundry load.
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as
the temperature and pressure of the incoming water, ambient temperature, amount of
detergent, load quantity and type, load balancing and any additional options selected.
1) Test programme in compliance with standard EN 50229 (Wash):
This cycle is designed for normally soiled cotton loads and is the most ecient in terms of
both electricity and water consumption; it should be used for garments washable at 60°C or
at 40°C. The actual washing temperature may dier from the indicated value.
Test programme in compliance with standard EN 50229 (Drying): select the 8 wash
programme and set the drying level to “EXTRA”, for both loads. The rst drying cycle must be
carried out with the nominal load.
PRODUCT DESCRIPTION
1.
3.
2.
5.
4.
7.
6.
8.
1. Top
2. Detergent dispenser drawer
3. Control panel
4. Handle
5. Porthole door
6. Drain pump (behind the plinth)
7. Plinth (removable)
8. Adjustable feet (2)
13
7
8
9
10
11
12
1 2
4
DISPLAY
5 6
3
Maximum load 11 kg
Power input in o mode 0.5 W / in left-on mode 8 W
Detergents and
Additives
Recommended
detergent
Wash cycle
Temperature
Maximum
spin
(r.p.m.)
Max.
load
(kg)
Duration
(Minutes)
Drying
Wash
Fabric
softener
Powder Liquid
Default Range
1 2
1 Daily Wash & Dry (Daily Mix Wash & Dry) 40 °C
- 40 °C 800 3,0
The duration of the wash cycles can be checked on the display.
–
2 Shirts Wash & Dry 40 °C
- 40 °C 1000 2,0
–
3 Pre Iron – – – 1,5 – – – – –
4 Steam Refresh – – – 2,0 – – – – –
5 Anti-Stain Turbo 45’ (Anti Stain Turbo 45’) 20 °C
- 40 °C 1200 5,5
–
6 Anti-Stain Power 20°C (Anti Stain Power 20°C) 20 °C
- 20 °C 1600 11,0
–
7 Cotton 40 °C
- 90 °C 1600 11,0
8
Eco Cotton
60°/40°
(1-2)
60 °C
- 60 °C 1600 11,0
9 Synthetics (3) 40 °C
- 60 °C 1000 5,0
10 Multicolour (Multi Colour) 40 °C
- 40 °C 1600 11,0
–
11 Ultradelicates (Ultra Delicates) 30 °C
- 30 °C -- 1,0
–
12 Wool 40 °C
- 40 °C 800 2,5
–
13 Sport 40 °C
- 40 °C 600 4,5
–
14 Fast (Fast 30') ** 30 °C
- 30 °C 800 4,0
–
Rinse – – 1600 11,0
–
– –
Spin + Pump out * – – 1600 11,0
– – – –
Required dosage Optional dosage
DETERGENT DISPENSER DRAWER
Compartment *:
Do not insert detergent in this compartment.
Compartment 1: Washing detergent (powder
or liquid)
If liquid detergent is used, the removable plastic
partition A (supplied) should be used for proper
dosage.
If powder detergent is used, place the partition
into slot B.
Compartment 2: Additives (fabric softeners, etc.)
The fabric softener must not exceed the “MAX” level.
! Use powder detergent for white cotton garments, for pre-washing, and
for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
1
2
A
B
*
14
Loading ...
Loading ...
Loading ...