Loading ...
Loading ...
Loading ...
ENGLISH
DESCRIPTION
The appliance can be a filtering version one, a ducting version one or with an external motor.
In the Filtering version (Fig. 1), the air and vapours conveyed by the appliance are depurated by charcoal filter
and recirculated around the room. ATTENTION: Using the hood as a filtering one it is necessary to use the charcoal
filter that purifies the air sent back into the room.
In the Ducting version (Fig. 2), cooking vapours and odours are conveyed straight outside by a disposal duct
which passes through the wall/ceiling. Use of charcoal filter is therefore unnecessary.
In the version with an External motor (Fig. 3), the appliance must be connected to an ducting apparatus/motor
which works on its own using the appliance as a union for the air to be scavenged. Use only motors proposed
in the original catalogue.
If your appliance is made of stainless steel, it might be covered with a protective film: remove it before installation.
INSTALLATION
Before assembling, in order to manoeuvre the appliance more easily, take off the grease filters: at the handle, push the
stop inwards and pull the filter downwards (Fig. 4); open the trolley and take off the other filter doing the same.
IMPORTANT: So as not to damage your product, during installation USE ONLY THE SCREWS PROVIDED. Make
sure these are used as shown in the following instructions.
Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical
hazards.
To compensate possible depth voids between the appliance and the wall, a plastic SPACING BAR to be fixed at the
back of the appliance by means of the three screws A is included (Fig. 5). The 3 screws A to be used are contained
in the accessory bag attached to the plastic spacing bar. Cut the spacing bar according to the distance to be adjusted.
ASSEMBLY UNDER A PENSILE CUPBOARD
The following operations are essential for assembly:
– Install the wiring system
– Prepare the air venting hole if your appliance is to be installed in the ducting version or in the version with an external
motor.
Fixation as indicated in Fig. 6:
Make the 4 necessary fixing holes in the bottom of the cupboard and cut the air venting hole. Move the hood
close to the bottom of the wall unit and then connect the two units by means of the 4 self-tapping screws supplied
together with the appliance.
Fixation with brackets as in Fig. 7 (OPTIONAL):
Take the two brackets (S) out of the accessory bag together with the 4 screws provided. Fit the brackets to the
wall unit being careful to position these correctly; for this operation use the 4 longer screws. At this point,
adjust the angle of the appliance with the 4 screws (B) and fasten the appliance to the brackets using the
2 shorter screws (C).
Ducting version and version with an external motor: connect the flange of the hood with the air venting hole made previously
in the wall/ceiling by means of an adequate tube. Make the electrical connections.
For the version with an External motor, make the electrical connection between the hood and the external motor
by means of the proper terminal board (Fig. 8): take off the cable clamp A and the cover B of the wiring junction
box. Fix the connection cable of the motor onto the terminal board C. Reassemble the cable clamp A and the
cover B of the junction box. The other end of the cable must be fixed onto the terminal board of the external
motor.
Filtering version : connect an adequate pipe to the connecting flange of the appliance so that it conveys the air up to
the top of the pensile cupboard (pipe is not provided). Make the electrical connections.
HOW TO TAKE OFF THE GLASS
Before any cleaning or any servicing it is necessary to disconnect the apparatus. To take off the glass, open the trolley
pulling it frontwards; pull the glass towards the left (or the right) and lift one side upwards as it is indicated in the Figure16.
OPERATION
Depending on the model, the unit is equipped with the following controls:
CONTROLS shown in Fig. 9:
MOTOR - Switch A. When set on position "1" the motor will be switched on and off automatically by opening and closing
the telescopic visor. When set on position "0" the motor will remain off at all times.
SPEED - Switch B. Allows the operating speed of the motor to be regulated by means of an electronic speed variator.
Loading ...
Loading ...
Loading ...