Loading ...
Loading ...
Loading ...
9
Care and Cleaning
Cleaning the Igniters and
Other Burner Components
WARNING
Use care while cleaning the igniters. The porcelain is
fragile and can crack or break.
IMPORTANT: The igniter will not work correctly if it
or the other burner parts are not clean. Dirty or wet
igniters may not spark at all.
Use a small amount of rubbing alcohol instead
of water to clean away grease and debris.
After disassembling the burners, check for any dirt
or grime deposited on the individual parts, including
the igniters.
1. Clean completely around the igniter, including
over and under the edge of the metal top and
porcelain base. A firm toothbrush is ideal for this
task. Use care while cleaning because the porce-
lain is fragile and can crack or break. Do not use
water to clean the igniters. If necessary, use a
small amount of rubbing alcohol to help dissolve
grime.
2. Examine the burner parts. Remove anything
stuck in the holes with a straightened paper
clip, wire or needle. Be careful not to scratch or
damage the ring and other parts. Do not distort
the shape of the burner holes.
3. Clean all the burner parts, including the burner
bases, with window cleaner or rubbing alcohol.
Use a cleaning brush with plastic bristles or a
firm tooth brush. When done, rinse the parts
well with clean water. Dry all the parts thor-
oughly before re-assembling them.
4. Reassemble the cooktop according to the burner
and grate assembly instructions on page 5.
Test the burners after reassembling them. If
the flame is uneven, be sure that all the burner
parts are properly positioned, then check for any
remaining dirt or grime on the burner parts or
igniter. If erratic clicking is still present, make
sure the igniter is completely dry. If the unit still
exhibits problems after drying, call your local
Dacor Authorized Service Agent.
Cleaning Stainless Steel
WARNING
Always wipe stainless steel (silver colored) surfaces with
the grain. To prevent scratching, do not use abrasive
cleaners or scrubbers on stainless steel surfaces.
• Clean stainless steel surfaces with the Dacor
Stainless Steel Cleaner included with your
cooktop. Use it according to the directions on
the package. You may order additional stain-
less steel cleaner at www.everythingdacor.com.
Order part number A302.
• You may also clean the stainless steel surfaces
with a mild solution of detergent and warm
water. Rinse and dry with a soft, lint-free cloth.
Cleaning the Knobs and Trim Rings
1. Turn the knobs to the off position.
2. Unplug the cooktop power plug from the
electrical outlet.
3. Grasp each knob and pull straight up to remove.
Do not remove the trim rings; they should be
cleaned while in place.
4. Wash the knobs with a solution of warm soapy
water. Dacor recommends hand dishwashing
liquid.
5. Wipe the trim rings with a solution of warm
soapy water on a soft damp rag. Avoid getting
water or moisture into the control panel behind
the trim rings.
6. Replace the knobs. Align the “D-shaped” open-
ing on the bottom of the knob with the tip of the
valve stem. Carefully push the knob onto the
stem until it stops.
7. Plug the cooktop power cord to an electrical
outlet.
Cleaning the Griddle Accessory
Clean the griddle after each use. Hot water and
liquid detergent are all that is needed to avoid stains
from grease build up. The griddle is coated with a
non-stick surface for easy cleaning.
Remove stubborn spots with a non-abrasive plastic
mesh pad.
To prevent scratching, do not use abrasive pads or
abrasive cleaners.
• Use the soft side of a sponge for scrubbing.
• Use a lint-free cloth for drying.
Burner base
Igniter
Loading ...
Loading ...
Loading ...