Hamilton Beach EXPEDITOR™ 600 Variable Speed Commercial Culinary Blender

User Manual - Transcript

• Page 2 - English - : GB Read the Operation Manual before using blender Keep Operation Manual handy Before first use wash container assembly in hot soapy water Do NOT place in dishwasher Plug into a grounded outlet Do not remove ground Do not use an adapter Do not use an extension cord Disconnect power before cleaning or servicing To reduce risk of personal injury unplug cord from outlet when not in use and before putting on or taking off parts Unplug the blender and inspect the power cord insulation for cracks on a weekly basis Refer to Technical Services for repair or replacement To protect against electrical shock do not immerse cord plug or blender base in water or any other liquid Do not spray the base with a highpressure spray gun Extreme caution must be used when moving an appliance containing hot oil or other hot liquids Do not use appliance for other than intended use Not intended for use by or near children This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety The use of accessory attachments not recommended by the appliance manufacturer may cause injuries To reduce risk of personal injury and to prevent damage to blender or container and cutter assembly DO NOT insert utensils into blender container while operating blender Do not store any kitchen utensils in the container because the blender would be damaged if inadvertently turned on To prevent possibility of serious personal injury keep hands out of blender container while operating blender Always operate blender with container cover in place Avoid contacting moving parts Switch off the appliance and disconnect from power supply before changing accessories or approaching parts that move in use Blades are sharp Handle carefully If cutter assembly blades are loose discontinue use immediately and replace cutter assembly Do not attempt to repair or tighten cutter assembly Inspect container and cutter assembly daily Do not use broken chipped or cracked container Check cutter for wear nicks or broken blades Do not use broken loose or cracked cutting blades Do not use outdoors This appliance is intended for short periods of operation with a rated operating time of 3 minutes Do not leave blender unattended while it is operating To prevent damage to blender container or cutter assembly DO NOT move or shake blender while in operation If blending action stops during operation turn blender OFF O remove container from base remove container cover and use a thin rubber spatula to push mixture towards cutters When blending hot liquids remove center piece of twopiece lid Hot liquids may push lid off jar during blending To prevent possible burns Do not fill blender jar beyond the 1 quart 1 liter level With the protection of an oven mitt or thick towel place one hand on top of lid Keep exposed skin away from lid Start blending at lowest speed Always operate blender with container cover in place This blender is designed with motor overload protection If the motor stops during operation due to overheating unplug the unit and allow it to cool down for 15 minutes Plug unit back after 15 minutes to resume normal operation The normal function of this product may be disturbed by strong electromagnetic interference If this occurs simply reset the product and resume normal operation by following the operation manual If normal operation cannot be resumed place the product in a different location Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard Refer to Technical Services for contact information on examination repair electrical or mechanical adjustment UK ONLY If fitted with a nonrewirable UK plug the 13amp fuse approved by ASTA to be BS1362 must be used If you need a replacement fuse carrier it must be replaced with the same colourcoded carrier with the same markings Fuse covers and carriers can be obtained from approved service agents SAVE THESE IN STRUC TIONS IMPORTANT SAFETY INSTRUCTIONS WARNING When using electrical appliances basic safety precautions should be followed including the following
• Page 3 - English - : Cut Hazard Always place cover on container when blending Do not put hands spoons or other utensils in container when blending Failure to follow these instructions can result in broken bones cuts or other injuries Burn Hazard Always use caution when blending hot contents Failure to follow these instructions can result in burns Sanitize using 1 tablespoon 15 ml of household bleach per 1 gallon 38 liter of clean cool water 60F16C mixed according to the instructions on the bleach 1 Fill container with sanitizing solution replace cover and filler cap and run on LOW 1 speed for 2 minutes Empty container 2 Wipe exterior with soft cloth dampened with sanitizing solution 3 Immerse cover and filler cap in sanitizing solution for 2 minutes 4 Place empty container on base and run on HIGH 10 speed for 2 seconds to remove any moisture from the cutter assembly 5 When ready to use rinse with clean water Please do not dispose of any electrical equipment as ordinary waste Help conserve natural resources and protect the environment when you have finished using this product please dispose of it at your local waste colleciton or recycling center in the area reserved for electrical equipment Contact your local authority to find the nearest waste collection center To remind you to dispose of this product responsibly and separately from ordinary waste it is marked with the symbol of a crossedout trash bin INSTRUCTIONS FOR PROPER DISPOSAL OF THIS PRODUCT PURSUANT TO THE EUROPEAN UNIONS DIRECTIVE ON ELECTRICAL WASTE For assistance or replacement parts call our Technical Services number 9106934277 wwwcommercialhamiltonbeachcom Technical Services Sanitizing Electrical Shock Hazard Disconnect power before cleaning blender base Failure to follow these instructions can result in death or electrical shock Electrical Shock Hazard Plug into a grounded outlet Do not remove ground Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock
• Page 4 - English - : 1 2 3 The location of the main power switch will be either on the front of the unit or on the bottom of the unit as indicated above Jar pad sensor with four magnetic connections to prevent blending unless container is on correctly Temperature gauge alerts operator if motor overheats while blending backtoback batches O I
• Page 10: 261 Yadkin Road Southern Pines NC 28387 310 wwwcommercialhamiltonbeachcom