Loading ...
Loading ...
Loading ...
9
Sanitizes dishes and glassware in accordance with
NSF International NSF/ANSI Standard 184 for
Residential Dishwashers. Certified residential
dishwashers are not intended for licensed food
establishments. Only sanitizing cycles have been
designed to meet the requirements of the NSF/ANSI
184 performance standard for soil removal and for
sanitization efficacy. There is no intention, either
directly or indirectly, that all cycles on a NSF/ANSI 184
certified dishwasher meet the NSF/ANSI 184
performance standard for soil removal and for
sanitization efficacy.
The Sanitize indicator glows at the end of the cycle if
the Sani Rinse option was successfully completed. If
the indicator does not activate, it is probably due to
the cycle being interrupted.
Sensor
Heavy
Normal
Raises the main
wash temperature
to 135°F (57°C)
and the final rinse
temperature to
156°F (69°C).
0:05 to 1:06 0 to 3.86
(0 to 14.6)
Dries dishes with heat. This option, with the use of
rinse aid, will provide the best drying performance.
Plastic items are less likely to deform when loaded in
the top rack. Use Heat Dry for optimum dry
performance. Turn the Heat Dry option off for air dry.
Sensor
Heavy
Normal
Soak & Clean
1 - Hour Wash
Uses heating
element to speed
drying times.
Heat Dry option
defaults to On
when any cycle is
selected except
for 1-Hour Wash.
0:08 to 0:46 0
Runs dishwasher at a later time. Select a wash cycle
and options. Each time you press the delay button, it
will display the next available delay time. Press
DELAY. Press START/RESUME. Close door firmly.
NOTES:
■ The dishwasher remembers the last Delay you
selected. To reset the delay time to something
other than what is displayed, continue to press
the Delay button until the desired delay time is
reached.
■ Anytime the door is opened (such as, to add a
dish); START/RESUME must be pressed again to
resume delay countdown.
Available with
any cycle
Delays start of a
cycle up to
24 hours.
0:00 0
Avoids unintended use of dishwasher between cycles, or cycle and option changes during a cycle.
To turn on Lock, press and hold SANI RINSE/CONTROL LOCK or DELAY (depending on model) for 3 seconds. Control Lock
light will stay on for a short time, indicating that it is activated, and all buttons are disabled. If you press any button while your
dishwasher is locked, light flashes 3 times. Dishwasher door can still be opened/closed while the controls are locked.
To turn off Lock, press and hold SANI RINSE/CONTROL LOCK or DELAY (depending on model) for 3 seconds. Light turns off.
NOTE: If your model requires you to press and hold DELAY to lock controls, Control Locked LED will be on or off to indicate
whether Control Lock is active or not.
CONTROLS AND CYCLE STATUS
CONTROL PURPOSE COMMENTS
Press to start or resume a wash cycle.
If the door is opened during a cycle or the power is interrupted, the Start/Resume button LED flashes. Cycle will
not resume until door is closed and Start/Resume is pressed.
NOTE: If Start/Resume button is located on top of door, push door firmly closed within 3 seconds of pressing
Start/Resume. If door is not closed within 3 seconds, Start/Resume button LED will flash, an audible tone will be
heard (on some top control models), and cycle will not start.
Press to cancel wash cycle.
Close the door firmly. The dishwasher starts a 2-minute drain (if needed). Let dishwasher drain completely. Press
and hold START/RESUME for 3 seconds.
OPTION SELECTIONS
OPTIONS CAN BE
SELECTED
WITH
WHAT IT DOES ADDED TIME
TO CYCLE
ADDED
WATER
GALLONS
(LITERS)
Loading ...
Loading ...
Loading ...