Loading ...
Loading ...
Loading ...
3. Pour cooking oil into Oil Reservoir until it reaches between the "MIN"
and "MAX" marks on the inside of the reservoir. DO NOT OVER OR
UNDER FILL.
4. Make sure that fryer is off and insert plug into 120 volt AC outlet.
5. Turn fryer to desired temperature position. The Power Indicator will
illuminate. The Ready Indicator will illuminate when the oil has reached
the preset temperature.
6. Using your slotted spoon, place food inside the fryer (Do not over stack
food). Close Lid until it snaps into place. Overloading will lower the oil
temperature, causing food to absorb too much oil and cook improperly.
7. For cooking times, see chart on page 8, or use the recommended times in
your recipe.
8. As your food fries, open lid and stir slowly with slotted spoon or other
heat-resistant utensil to prevent foods from sticking together.
9. Once the food reaches desired brownness, using your spoon, lift and drain.
Set the drained food on several layers of paper towels to absorb excess oil.
Season if desired. To fry more servings, repeat steps 5, 6, 7, 8 and 9.
WARNING: DO NOT USE THE DETACHABLE MAGNETIC CORD SYSTEM TO
DISCONNECT THE FRYER. ALWAYS DISCONNECT PLUG FROM
WALL OUTLET FIRST TO DISCONNECT FRYER.
Use only Model JB-168 magnetic cord set with this product. The use of any other
magnetic cord set may cause fire, electric shock, or injury.
CAUTION: The detachable magnetic cord is only for accidental disconnection
and not to be removed during normal operation. If the cord becomes
disconnected, the user should immediately unplug the cord set from
the wall outlet, then reconnect the magnetic cord to the deep fryer
and then to the wall outlet.
CARE AND CLEANING
WARNING: ALWAYS TURN CONTROL TO “OFF” THEN DISCONNECT PLUG
FROM WALL OUTLET BEFORE DISCONNECTING MAGNETIC CORD.
CAUTION:
• Do not immerse cord sets in water or any liquid.
• Do not attempt to defeat the detachable magnetic cord system by trying
to permanently attach cord set to product.
• Do not stick pins or other sharp objects in holes on magnetic cord set.
• Do not use any type of steel wool to clean magnetic contacts.
1. Turn unit OFF.
2. Unplug from outlet and allow unit to cool completely.
3. Remove magnetic cord from the fryer socket.
4. When unit has cooled, empty cooking oil. If you plan to reuse the oil, store
fryer with lid closed. (See TIPS FOR OIL USE AND STORAGE on page 10.)
5. When changing the oil, take the opportunity to clean the inside of the
fryer. Remove LID, pour out oil and discard properly; wipe the inside with
paper towels to absorb excess grease. Wash interior of fryer with hot soapy
water. Rinse and dry thoroughly. Do not use scouring pads or abrasive
kitchen cleaners.
CAUTION: Never immerse the fryer in water, or wash in running water.
NOTE: A REMOVABLE CONDENSATION TRAY is located on the back of the fryer
under the lid. The CONDENSATION TRAY will collect any water that has condensed
on the inside of the LID when the LID is opened after frying. Remember to
empty and clean the CONDENSATION TRAY after each use. To remove
condensation tray, remove lid and lift out condensation tray. To clean simply
rinse with warm water.
TO REMOVE AND REPLACE LID
• To remove lid, depress OPEN LID BUTTON and lift LID
to a vertical position. Remove LID by pulling firmly
upwards (See Figure 2). Reverse the sequence to
secure lid back into position. Be sure to push down
firmly on lid from the vertical position to secure back
in place.
Figure 2
www.oster.com
www.oster.com
6
7
CKSTDFFM15-B_13ESM1.indd 7-8 5/24/13 3:50 PM
Loading ...
Loading ...
Loading ...