Loading ...
Loading ...
Loading ...
denatured ethyl alcohol.
HOW TO TAKE OFF THE GLASS
Before any cleaning or any servicing it is
necessary to disconnect the apparatus. To
take off the glass, open the trolley pulling
it frontwards; pull the glass towards the left
(or the right) and lift one side upwards as
it is indicated in the Figure 12.
DESCRIPTION
--------------------------------------------------
The appliance can be used in both the filtering
and ducting version.
In the Filtering version (Fig. 1/2), the air and
vapours conveyed by the appliance are depu-
rated by activated charcoal fiber panel and
recirculated around the room. ATTENTION:
Using the hood as a filtering one it is neces-
sary to use the activated charcoal fiber panel(s)
that purifies the air sent back into the room.
In the Ducting version (Fig. 3), cooking va-
pours and odours are conveyed straight out-
side by a disposal duct which passes through
the wall/ceiling. Use of activated charcoal fiber
panel is therefore unnecessary.
According to the model you have bought, the
appliance can include 1 or 2 motors. In the I
motor version the flange for the air to be ex-
hausted has not got a central position, but it is
slightly on the left.
INSTALLATION
--------------------------------------------------
Before assembling, in order to manoeuvre the
appliance more easily, take off the grease grille
(Fig. 3): pull the front of the grille upwards;
desinsert the back from its seat.
IMPORTANT: So as not to damage your
product, during installation USE ONLY THE
SCREWS PROVIDED. Make sure these are
used as shown in the following instructions.
To compensate possible depth voids be-
tween the appliance and the wall, a plastic
SPACING BAR to be fixed at the back of the
appliance by means of the three screws A
is included (Fig. 5). The 3 screws A to be
used are contained in the accessory bag
attached to the plastic spacing bar. Cut the
spacing bar according to the distance to be
adjusted.
ASSEMBLY UNDER A PENSILE CUPBOARD
The following operations are essential for as-
sembly:
– Install the wiring system
– Prepare the air venting hole if your applian-
ce is to be installed in the Ducting version.
The filtering version of the apparatus can be
assembled as indicated in Fig.1, the air venting
system being upwards, or as indicated in Fig.2,
the air venting system being frontwards. For
installation according to Fig.2, do as follows:
1. Take off the air venting flange and put on
the supplied tap T instead (Fig. 6).
2. Take off plate P unscrewing the 3 screws
(Fig.6).
3. Take off the front plate F unscrewing the 2
screws A (Fig.6) and put a new plate
according to your requirement (minimum
height 80 mm).
Fixation as indicated in Fig. 7:
Using the relative template make the 4 nec-
essary fixing holes in the bottom of the cup-
board and cut the air venting hole: the open-
ing for the air venting is not necessary for
the filtering version of Fig. 2. Move the hood
close to the bottom of the wall unit and
then connect the two units by means of the
4 self-tapping screws supplied together with
the appliance.
Fixation with brackets as in Fig. 8 (optio-
nal):
Take the two brackets (S) out of the
accessory bag together with the 8 screws
provided. Fit the brackets to the wall unit
being careful to position these correctly; for
this operation use the 4 longer screws. At
this point, secure the appliance to the
brackets using the 4 shorter screws.
Ducting version: connect the flange of the hood
with the air venting hole made previously in the
wall/ceiling by means of an adequate tube.
Make the electrical connections. Assemble the
anti-grease grille with the hood, inserting it
obliquely (making the front side go upwards).
Filtering version: make the electrical connec-
tions. Set the fiber panel inside the anti-grease
grille blocking it by means of the 2 supplied
metal wires (F), as indicated in Fig. 4. Assem-
ble the anti-grease grille with the hood, insert-
ing it obliquely (making the front side go up-
wards).
Loading ...
Loading ...
Loading ...