Loading ...
Loading ...
Loading ...
6
POWER/CANCEL
Touch to turn the washer on and off. Touch to stop/cancel
a cycle at any time.
NOTE: Turning the Wash Cycle knob will also turn the
washer on.
WASH CYCLE KNOB
Turn the knob to select a cycle for your laundry load. An LED
will light up for the cycle selected.
NOTE: The Clean Washer with affresh
®
LED will flash when
the washer has run 30 wash cycles as a reminder to run the
Clean Washer with affresh
®
cycle.
See “Cycle Guide” for detailed descriptions of cycles.
NOTE: For best results when using the Overnight Wash &
Dry cycle, use for loads weighing 2 lbs or less, such as a
soccer uniform or a running tank and shorts. Allow the cycle
to run the full duration of 12 hours.
START
Touch and hold for 3 seconds until the light above START
comes on to start a cycle or touch once while a cycle is in
process to pause it. If you want to add a garment, you can
touch START when the “Add a Garment” LED is on.
LED DISPLAY AND SETTINGS
When you select a cycle, its default settings will light up and
the Estimated Time Remaining will be displayed. Factors
such as load size, wash temperature, and water pressure
may affect the time shown in the display. Tightly packing,
unbalanced loads, or excessive suds may cause the washer
to lengthen the cycle time as well.
Touch the desired setting along the bottom of the display
to adjust. See “Cycle Guide” for available settings on each
cycle. Not all settings are available with all cycles.
Temperature
The recommended wash temperature is preset for each
cycle. You may also select a wash temperature based
on the type of fabric and soils being washed. For best
results, use the warmest wash water safe for your
fabric, following the garment label instructions. All wash
temperatures feature a cold rinse.
Soil Level
Soil Level (wash time) is preset for each wash cycle.
When you change the soil setting, the cycle time will
increase or decrease in the Estimated Cycle Time
display.
For most loads, use the soil level that is preset with the
cycle you have chosen. For heavily soiled and sturdy
fabrics, use the Soil Level setting to select more wash
time. For lightly soiled and delicate fabrics, use the Soil
Level setting to select less wash time. Lower soil level
settings will help reduce tangling and wrinkling.
Spin Speed
This washer automatically selects the spin speed
based on the cycle selected. Some preset speeds
can be changed.
n Faster spin speeds mean shorter dry times but may
increase wrinkling in your load.
n Slower spin speeds reduce wrinkling but will leave
your load more damp.
1
2
3
4
USE OPTIMAL DISPENSE – DETERGENT
CONCENTRATION AND WATER HARDNESS
Touch – or + to set detergent concentration from 2x to
6x. Touch WATER HARDNESS to set water hardness
level (normal, hard, or soft). (See “About Detergent
Concentration” section.)
IMPORTANT: When using the dispenser cartridge with
concentrated liquid detergent, be sure to change the
detergent concentration settings in the control if the detergent
used is different than factory preset of 2x concentration.
DELAY START
Use + and – to delay the start of the wash cycle by 9 to 12
hours, depending on model. To turn off Delay Start, use +
and – to set the delay time to “0” or touch POWER/CANCEL.
CYCLE STATUS LIGHTS
NOTE: Not all Cycle Status Lights are available on all
models.
The Cycle Status Lights show the progress of a cycle.
At each stage of the process, you may notice sounds
or pauses that are different from traditional washers.
Low Detergent
This will light if there is enough detergent
in the Optimal Dispense cartridge for only
a few more cycles.
Refill Detergent
This will light if there is no detergent
in the Optimal Dispense cartridge.
Delay
If a Delay Start is set, the Delay indicator
will light and the delay time will count down
in the display.
Door Locked
Door Locked will light to indicate that
the door is locked and cannot be opened
without first pausing or canceling the cycle.
Sensing
When START is touched and held, the washer will first
perform a self-test on the door lock mechanism and the
sensing light will come on. You will hear a click, the drum will
make a partial turn, and the door will click again as it unlocks
briefly. The door will click one more time when it locks again.
Once the door has locked the second time, the washer will
begin tumbling and adding water. This sensing process will
continue throughout the cycle. You may also hear water
flowing through the dispenser, adding detergent to the load.
After the load size is sensed, the estimated time based on
load size will be displayed. The actual cycle time may be
lengthened; however, the display will continue to show the
estimated time.
The sensing light will blink once a second at various times
during the cycle, such as when the washer is reducing
extra suds.
Add a Garment
When “Add a Garment” is lit, you may pause the washer,
open the door, and add items. Touch and hold START to
start the washer again.
Steaming
This will light to show that the cycle is using a steam boost
for added cleaning power.
Done
Once the cycle is complete, this light will come on. Remove
the load promptly for best results. The Done indicator is also
lit during Fresh Hold
®
or Fresh Spin™ option.
6
7
5
Loading ...
Loading ...
Loading ...