Loading ...
Loading ...
Loading ...
10
4. Remove any excess coee from the rim of the lter holder
and attach the lter holder to the appliance. To attach
correctly, align the lter holder handle with the INSERT
symbol (g. 9), attach the lter holder and rotate the
handle towards the right until aligned with the CLOSE
symbol.
5. Place the cup or cups under the lter holder spouts (g.
10). You are recommended to warm the cups before
making coee by rinsing them with a little hot water.
6. Make sure the lights corresponding to the coee buttons
are on, then press the
or coee button. The
appliance proceeds to make the coee and delivery is
interrupted automatically.
How to make espresso coee using pods
Please note:
use pods conforming to the ESE standard, indicated on the pack
by the following symbol.
The ESE standard is a system accepted by
leading pod producers and enables espresso
coee to be prepared simply and cleanly.
1. Place the lter for coee pods (with the
symbol on
the bottom) in the lter holder.
2. Insert the pod, centring it as far as possible on the lter
(g. 11). Always follow the instructions on the pod pack to
position the pod on the lter correctly.
Proceed as described in points 4 to 6 in the previous section.
Please note:
• While the appliance is making coee, delivery can be
interrupted at any moment by pressing the coee button
pressed previously.
• At the end of delivery (within 3 seconds), to increase the
amount of coee in the cup, press and hold the coee
button pressed previously. Delivery is automatically
interrupted after a few seconds.
• To remove the lter holder, turn the handle from right to
left.
Danger of burns!
To avoid splashes, never remove the lter holder while the
appliance is delivering coee. Always wait for a few seconds
after delivery.
Programming the quantities of coee in the cup
The appliance is set by default to automatically deliver standard
quantities.
To change these quantities, proceed as follows:
1.
Place one or two cups under the lter holder spouts.
2. Press and hold the button you want to programme (
or ). The appliance starts delivering coee and the
other coee button ashes to indicate that programming
is underway.
3. Once the required quantity of coee has been delivered
into the cup, release the button. Delivery stops and the
light ashes to indicate that the quantity has been saved
correctly.
4. When the two coee lights come on steadily, the appliance
is ready for use.
HOW TO MAKE CAPPUCCINO
1. Prepare the espresso coees as described in the previous
paragraphs, using suciently large cups.
2. Press the
button (g. 12). The light ashes;
3. In the meantime, ll a recipient with about 100 g of milk
for each cappuccino to be prepared.
The milk must be at refrigerator temperature (not hot!).
In choosing the size of the recipient, bear in mind that the
milk doubles or triples in volume (g. 13).
Please note:
You are recommended to use semi-skimmed milk at refrigerator
temperature.
4. Wait for the light corresponding to the
button to
come on steadily, indicating that the boiler has reached
the ideal temperature to produce steam.
5. Position an empty container under the cappuccino maker
and open the dial for a few seconds to eliminate any air left
in the circuit. Close the dial again.
6. Place the recipient containing the milk under the
cappuccino maker.
7. Dip the cappuccino maker in the milk for a few millimetres
(g. 14).
Turn the dial to the
position. Steam is delivered
from the cappuccino maker, giving the milk a creamy
frothy appearance. To obtain a creamier froth, immerse the
cappuccino maker in the milk and rotate the container with
slow upward movements.
8. When the milk has doubled in volume, immerse the
cappuccino maker deeply and continue heating the milk
(g. 15). When the required temperature (the ideal is 60°C)
and froth density is reached, interrupt steam delivery by
turning the steam dial clockwise.
9. Pour the frothed milk into the cups containing the espresso
coee prepared previously.
Loading ...
Loading ...
Loading ...