Loading ...
Loading ...
Loading ...
Table 2. Eyebrow Comb
Setting
1
2
3
Remaining hair length (in.) /(mm)
.11 in/3mm
.24 in/6mm
.35 in/9mm
6 Move the eyebrow comb over the eyebrow from the outer tip of
the eyebrow towards the base of the nose (fig. 18).
7 Turn off trimmer. Rinse eyebrow comb clean after each use.
Contouring Eyebrows With Micro Trimmer (HP6378 only)
Use the micro trimmer on eyebrows without a comb if you are:
w Shaping eyebrows
w Defining eyebrow contours
w Removing single, unwanted hairs
1 Be certain trimmer is in the OFF position.
2 Put the micro trimmer on the handle.
3 Switch the trimmer ON.
4 For contouring eyebrows, stretch the skin of the eyelid (fig. 19).
Be careful when you use the micro trimmer as it removes every hair it
touches.
5 Make well-controlled movements making sure the micro trimmer
is in full contact with the skin. Always move the micro trimmer
against the direction of hair growth.
Be careful not to use the micro trimmer too close to a mirror.
IMPORTANT: Do not try to trim your eyelashes. Be careful not to get
too close to your eyelashes and eyes!
6 Turn off trimmer. Rinse micro trimmer clean after each use.
Cleaning
w The trimmer should be cleaned after each use.
w Always switch trimmer OFF, unplug and remove power supply cord
from trimmer before cleaning.
w Do not use abrasive cleaning agents, scourers or liquids such as
alcohol, benzene, bleach or acetone to clean the trimmer and
attachments.
w Never clean, replace or remove attachments with motor ON.
w Do not apply pressure to cutters.
w Do not touch cutters with hard objects as this may damage them.
During Use:
w If cut hairs have accumulated in the attachments, remove hairs by
shaking, blowing or using cleaning brush provided. Remember to
adjust the hair length selector back to your selected setting when
you replace the precision comb on trimmer.
After Each Use:
1 Make sure the trimmer is switched OFF and disconnected from
the electrical outlet.
2 Remove any attachment from trimmer.
3 Blow and/or shake out any hair that may have accumulated in
the attachment.
4 To clean the micro shaver (HP6378 only), pull the foil in the
direction of the arrow to remove from base of micro shaver (fig. 20).
5 Clean the cutter and the inside of the shaving foil carefully with
the brush or under warm tap water.
Do not use a towel to dry the micro shaver as damage to the shaving
foil could occur.
w The shaving foil is very delicate. Handle carefully.
w If foil becomes damaged, replace immediately. Do not continue
using the appliance. Do not apply pressure to shaving foil.
w Do not clean the foil with the brush, as this may cause damage.
Epilating (HP6378 only)
Use the epilating head to epilate your bikini line.
w Make sure your skin is clean, free from grease and creams. Do not
apply any cream before using. Hairs are easier to remove after a
bath or a shower, but your skin should be completely dry before
using the epilating head.
w If your hair is longer than .20in/5mm, first trim hair using the
precision trimmer with the precision comb at setting #3.
w With first time use you may feel some discomfort, irritation or
experience reddening of the skin. This is because the hairs are
actually being removed at the root. The discomfort you feel will
tend to lessen with successive uses. However, if the irritation
remains for more than three days, consult your doctor.
w After epilation, regrowth of hairs tends to be softer both in
appearance and in touch.
1 Be certain trimmer is in the OFF position.
2 Put the epilating head on the handle.
3 Switch trimmer ON.
4 To epilate the most effective way, move the epilating head against
the direction of hair growth. Make sure the surface of the
epilating head always stays in contact with the skin (fig. 15).
For easier epilating, stretch the skin with your free hand.
Do not exert any pressure when epilating.
5 Turn off trimmer. Rinse epilating head clean after each use.
Shaving With Micro Shaver
Use the micro shaver to shave along contoured edges to remove any
stubble while creating a smooth, well-defined bikini line.
w Before using the micro shaver, always check it for wear and damage.
If the micro shaver shows signs of wear or damage, do not use it
as injury may occur. Do not use the micro shaver until it has been
replaced.
1 Pre-trim the contours desired with the precision trimmer
without a comb.
2 Remove the precision trimmer from handle (fig. 12).
3 Put the micro shaver on the handle.
4 Remove the protective cap (fig. 13).
5 Switch the trimmer ON.
6 Gently press the micro shaver onto the skin and shave against
the direction of hair growth along contoured edges to remove
any stubble (fig. 14). Do not press too hard.
Trimming Eyebrows With Eyebrow Comb (HP6378 only)
Use the precision trimmer with the eyebrow comb to trim entire
eyebrow to a uniform length.
1 Be certain trimmer is in the OFF position.
2 Put the precision trimmer on the handle (fig. 3). You will hear
a click.
3 Slide the eyebrow comb into the guiding grooves on both sides
of the precision trimmer and push until it “clicks” into place
(fig. 16).
4 Press the hair length selector (1) and slide it up or down (2)
to the desired hair length setting (fig. 17). The selected setting
number will appear on the colored circle on the handle.
See Table 2 for settings.
5 Comb the eyebrow in the direction of hair growth.
w If you are trimming for the first time, start by using the comb at
the maximum trimming length setting (#3) to prevent accidentally
trimming hairs too short.
Loading ...
Loading ...
Loading ...