Loading ...
Loading ...
Loading ...
8
GB
The Controls
• PROGRAMMES knob
! Warning, if after pressing the Start/Pause button , the
programmes knob position has changed, the new position
will NOT change the programme selected. To change a
selected programme, press the Start/Pause button , the
light flashes Amber to indicate the programme is paused.
Select the new programme and any options required, the
light will then flash green. Press the Start/Pause button
again and the new programme will start.
• Option buttons / lights
These buttons are used to customise the
selectedprogramme to your requirements. Not all
options are available for all programmes (see Start and
Programmes). If an option is not available and you press
the button, the buzzer will beep three times. If the option is
available the option light next to the button lights to confirm
the selection.
Progress (Drying, Cool Tumble, End) /Delay (3hr, 6hr, 9hr)
Lights
When the light next to the delay button is on, these lights
flash to indicate the delay time selected. During other
programmes they indicate the progress of the dryer, each
one comes on as the corresponding phase starts.
Delay Timer
The start of some programmes (see Start and Programmes)
can be delayed for up to 9 hours in 3hr steps. Ensure the
water bottle is emptied before setting a delayed start. When
a delayed start is in progress the light next to the delay
button will be on and the selected delay period light will flash
(after the start button has been pressed). To set a delayed
start, press the Delay Timer button, and the light next to
the button will come on together with the 3hr delay light.
Pressing the button again will advance the delay setting to
6hr, the 3hr light goes out and the 6hr light is on. Each time
you press the button the delay setting advances 3 hours,
as indicated by the corresponding light. If the 9hr light is on,
pressing the button again will cancel the delay. Holding in
the On/Off button will also cancel.
Pre Care
When a delayed start and this option have been selected the
clothes are tumbled occasionally during the delayed period
to help prevent creases developing.
High Heat
Available for Timed Drying Programmes. Press this button
and a high heat setting is selected and the light next to the
button comes on. Timed programmes have a default of low
heat, if the light alongside the button is on then pressing the
button selects a low heat setting and the light goes out.
Post Care
When selected, the clothes are occasionally tumbled after
the end of the drying and cool tumble cycles, to help prevent
creases developing should you not be available to remove
the load immediately the programme is complete. The End
light is on during this phase.
Empty Water Light / Container
(If you have plumbed your dryer to a drain this light can be
ignored, as there is no need to empty the water container).
When this light is on (not flashing) it reminds you to empty
the water container. If the water container fills during a
programme, the heater turns off and the dryer does a period
of Cool Tumble then the light flashes and the buzzer sounds.
You must empty the water container and restart the dryer
or the clothes will not dry. After re-starting the dryer, the
light will take a few seconds to go out.To avoid this always
empty the water container each time you use the dryer (see
Maintenance).
• Door Opening
Opening the door (or pressing the Start/Pause button )
during a programme will stop the dryer and have the following
effects:
• The Start/Pause light flashes Amber.●
• During a delay phase the delay will continue to count down
The Start/Pause button must be pressed to resume the
delay programme.
One of the delay lights will flash to show the
current delay setting.
●•The Start/Pause button must be pressed to resume
the programme. The progress lights will change to show the
current status and the Start/Pause light will stop flashing and
turn green.
●•During the Post Care phase of a drying programme, the
programme will finish. Pressing the Start/Pause button will
re-start a new programme at the beginning.
●•Changing the programmes knob will select a new
programme and the Start/Pause light will flash green. You
can use this to select the Cool Tumble programme to
cool the clothes, if you find them dry enough. Press the Start/
Pause button to begin a new programme.
●• Note
●If you have a power cut, switch off the power or remove the
plug. When power is restored, press and hold the ON/OFF
button until the dryer reactivates, then press the Start/Pause
button.
Start and Programmes
Loading ...
Loading ...
Loading ...