Loading ...
Loading ...
Loading ...
14
Oven Light
The oven light is a standard 40-watt appliance bulb. Before
replacing, make sure the oven and cooktop are cool and the
control knobs are in the off position.
To Replace:
1. Unplug range or disconnect power.
2. Turn the glass bulb cover in the back of the oven
counterclockwise to remove.
3. Turn bulb counterclockwise to remove from socket.
4. Replace bulb, then bulb cover by turning clockwise.
5. Plug in range or reconnect power.
TROUBLESHOOTING
First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call, refer
to the warranty page in this manual and scan the code there with your mobile device, or visit http://www.whirlpool.com/product_help.
Contact us by mail with any questions or concerns at the address below:
In the U.S.A.:
Whirlpool Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
Operation
PROBLEM POSSIBLE CAUSES SOLUTIONS
Nothing will operate Power supply cord is unplugged. Plug into a grounded outlet.
ENERGY SAVE is active, and the
display is blank.
Press any key on the control to display the Time of Day. See the
“Electronic Oven Controls” section for more information.
Household fuse is blown, or a circuit
breaker is tripped.
Replace the fuse or reset the circuit breaker. If the problem
continues, call an electrician.
The control displays an F9 or F9 E0
error code.
The electrical outlet in the home may be miswired. Contact a
qualified electrician to verify the electrical supply.
Cooktop will not operate The control knob is not set correctly. Push in knob before turning to a setting.
On ceramic glass models, the oven
control lockout is set.
See the control lock keypad feature in the “Feature Guide.”
Excessive heat around
cookware on cooktop
Cookware is not the proper size. Use cookware about the same size as the surface cooking
area, element or surface burner. Cookware should not extend
more than ¹⁄₂" (1.3 cm) outside the cooking area.
Cooktop cooking results
not what expected
Control knob set to incorrect heat
level.
See “Cooktop Use” section.
Range is not level. Level the range. See the Installation Instructions.
Cooktop element cycles
on and off on High setting.
Element cycling due to a temperature
limiter.
This is normal operation. The element may cycle on and off to
keep the cooktop from overheating.
Oven will not operate Delay start is set. See “Cook Time” section.
Control lock is on. Press and hold START for 3 seconds to unlock.
Control is in Demo Mode. Press and hold START TIME for 10 seconds to exit Demo
Mode. Demo Mode is used for display models in a showroom.
Electronic oven control set incorrectly. See “Electronic Oven Controls” section.
Oven temperature too
high or too low
Oven temperature needs adjustment. See “Oven Temperature Control” in the “Electronic Oven
Controls” section.
Oven indicator lights flash Power to range is turned on or
restored.
See “Control Display” in the “Electronic Oven Controls”
section. If the indicator lights keep flashing, call for service. See
cover for contact information.
Display shows messages Power failure (display shows flashing
time).
Clear the display. On some models, reset the clock, if needed.
See “Clock” keypad feature in the “Feature Guide” section.
Error code (display shows letter
followed by number).
Depending on your model, press CANCEL to clear the display.
See “Control Display” in the “Electronic Oven Controls”
section. If it reappears, call for service. See cover for contact
information.
Start needs to be pressed so a cycle
can begin (display shows “PUSH” or
“PSH”).
See the “Start” keypad feature in the “Feature Guide” section.
Loading ...
Loading ...