PN-E702 Sharp User Manual

PN-E702

LCD MONITOR

OPERATION MANUAL

IMPORTANT:

To aid reporting in case of loss or theft, please record the

product’s model and serial numbers in the space provided.

The numbers are located in the rear of the product.

Model No.:

Serial No.:

U.S.A. ONLY

FOR CUSTOMERS IN U.K.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

GREEN-AND-YELLOW: Earth

BLUE: Neutral

BROWN: Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

•ThewirewhichiscolouredGREEN-AND-YELLOWmustbeconnectedtotheterminalintheplugwhichismarkedbythe

letter E or by the safety earth

orcolouredgreenorgreen-and-yellow.

•ThewirewhichiscolouredBLUEmustbeconnectedtotheterminalwhichismarkedwiththeletterN or coloured black.

•ThewirewhichiscolouredBROWNmustbeconnectedtotheterminalwhichismarkedwiththeletterL or coloured red.

Ensurethatyourequipmentisconnectedcorrectly.Ifyouareinanydoubtconsultaqualiedelectrician.

“WARNING: THIS APPARATUS MUST BE EARTHED.”

IMPORTANT INFORMATION

WARNING: TOREDUCETHERISKOFFIREORELECTRICSHOCK,DONOTEXPOSETHISPRODUCT

TORAINORMOISTURE.

RISKOFELECTRIC

SHOCK

DONOTOPEN

CAUTION

CAUTION: TOREDUCETHERISKOFELECTRIC

SHOCK,DONOTREMOVECOVER.

NOUSER-SERVICEABLEPARTS

INSIDE.

REFERSERVICINGTOQUALIFIED

SERVICEPERSONNEL.

Thelightningashwitharrowheadsymbol,within

anequilateraltriangle,isintendedtoalertthe

user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

beofsufcientmagnitudetoconstituteariskof

electric shock to persons.

The exclamation point within a triangle is

intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

product.

WARNING:

FCCRegulationsstatethatanyunauthorizedchangesormodicationstothisequipmentnotexpresslyapprovedbythe

manufacturercouldvoidtheuser’sauthoritytooperatethisequipment.

NOTE:

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforClassAdigitaldevice,pursuanttoPart15ofthe

FCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferencewhentheequipment

isoperatedinacommercialenvironment.Thisequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,if

not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operationofthisequipmentinaresidentialareaislikelytocauseharmfulinterferenceinwhichcasetheuserwillberequired

to correct the interference at his own expense.

ThisproductutilizesaCRcoinLithiumbatterywhichcontainsaPerchloratematerial.

Special handling for this material may apply,

Californiaresidents,Seewww.dtsc.ca.gov/hazardouswaste/perchlorate/

Others,consultlocalenvironmentalofcers.

U.S.A. ONLY

IMPORTANT INFORMATION (Continued)

A. Information on Disposal for Users (private households)

1. In the European Union

Attention:Ifyouwanttodisposeofthisequipment,pleasedonotusetheordinarydustbin!

Usedelectricalandelectronicequipmentmustbetreatedseparatelyandinaccordancewithlegislationthatrequiresproper

treatment,recoveryandrecyclingofusedelectricalandelectronicequipment.

Followingtheimplementationbymemberstates,privatehouseholdswithintheEUstatesmayreturntheirusedelectricaland

electronicequipmenttodesignatedcollectionfacilitiesfreeofcharge*.Insomecountries*yourlocalretailermayalsotake

back your old product free of charge if you purchase a similar new one.

*)Pleasecontactyourlocalauthorityforfurtherdetails.

Ifyourusedelectricalorelectronicequipmenthasbatteriesoraccumulators,pleasedisposeoftheseseparatelybeforehand

accordingtolocalrequirements.

Bydisposingofthisproductcorrectlyyouwillhelpensurethatthewasteundergoesthenecessarytreatment,recoveryand

recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due

to inappropriate waste handling.

2. In other Countries outside the EU

If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.

ForSwitzerland:Usedelectricalorelectronicequipmentcanbereturnedfreeofchargetothedealer,evenifyoudon’t

purchaseanewproduct.Furthercollectionfacilitiesarelistedonthehomepageofwww.swico.chorwww.sens.ch.

B. Information on Disposal for Business Users

1. In the European Union

If the product is used for business purposes and you want to discard it:

PleasecontactyourSHARPdealerwhowillinformyouaboutthetake-backoftheproduct.Youmightbechargedforthe

costsarisingfromtake-backandrecycling.Smallproducts(andsmallamounts)mightbetakenbackbyyourlocalcollection

facilities.

ForSpain:Pleasecontacttheestablishedcollectionsystemoryourlocalauthorityfortake-backofyourusedproducts.

2. In other Countries outside the EU

If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.

Attention: Your product is marked with this symbol. It means that used electrical and electronic products

should not be mixed with general household waste. There is a separate collection system for these products.

The battery supplied with this product contains traces of Lead.

ForEU:

Thecrossed-outwheeledbinimpliesthatusedbatteriesshouldnotbeputtothegeneralhousehold

waste!Thereisaseparatecollectionsystemforusedbatteries,toallowpropertreatmentandrecyclingin

accordance with legislation. Please contact your local authority for details on the collection and recycling

schemes.

ForSwitzerland:

The used battery is to be returned to the selling point.

Forothernon-EUcountries:

Please contact your local authority for correct method of disposal of the used battery.

“BATTERYDISPOSAL”

THISPRODUCTCONTAINSALITHIUMPRIMARY(MANGANESSDIOXIDE)MEMORYBACK-UPBATTERYTHAT

MUSTBEDISPOSEDOFPROPERLY.PLEASECONTACTYOURLOCALSHARPDEALERORAUTHORIZEDSERVICE

REPRESENTATIVEFORASSISTANCEINDISPOSINGOFTHISBATTERY.

U.S.A.ANDCANADAONLY

EUONLY

ThankyouforyourpurchaseofaSHARPLCDproduct.Toensuresafetyandmanyyearsoftrouble-freeoperationofyour

product, please read the Safety Precautions carefully before using this product.

SAFETY PRECAUTIONS

Electricityisusedtoperformmanyusefulfunctions,butitcanalsocausepersonalinjuriesandpropertydamageifimproperly

handled.Thisproducthasbeenengineeredandmanufacturedwiththehighestpriorityonsafety.However,improperusecan

resultinelectricshockand/orre.Inordertopreventpotentialdanger,pleaseobservethefollowinginstructionswheninstalling,

operatingandcleaningtheproduct.ToensureyoursafetyandprolongtheservicelifeofyourLCDproduct,pleasereadthe

following precautions carefully before using the product.

1. Readinstructions—Alloperatinginstructionsmustbereadandunderstoodbeforetheproductisoperated.

 2. Keepthismanualinasafeplace—Thesesafetyandoperatinginstructionsmustbekeptinasafeplaceforfuture

reference.

 3. Observewarnings—Allwarningsontheproductandintheinstructionsmustbeobservedclosely.

 4. Followinstructions—Alloperatinginstructionsmustbefollowed.

 5. Cleaning—UnplugthepowercordfromtheACoutletbeforecleaningtheproduct.Useadryclothtocleantheproduct.Do

notuseliquidcleanersoraerosolcleaners.

 6. Attachments—Donotuseattachmentsnotrecommendedbythemanufacturer.Useofinadequateattachmentscanresult

in accidents.

 7. Waterandmoisture—Donotusetheproductnearwater.Donotinstalltheproductinaplacewherewatermaysplashonto

it.Becarefulofequipmentwhichdrainswatersuchasanair-conditioner.

 8. Ventilation—Theventsandotheropeningsinthecabinetaredesignedforventilation.

  Donotcoverorblocktheseventsandopeningssinceinsufcientventilationcancauseoverheatingand/orshortenthelife

oftheproduct.Donotplacetheproductonasofa,rugorothersimilarsurface,sincetheycanblockventilationopenings.

Donotplacetheproductinanenclosedplacesuchasabookcaseorrack,unlessproperventilationisprovidedorthe

manufacturer’s instructions are followed.

 9. Powercordprotection—Thepowercordsmustberoutedproperlytopreventpeoplefromsteppingonthemorobjectsfrom

resting on them.

10. TheLCDpanelusedinthisproductismadeofglass.Therefore,itcanbreakwhentheproductisdroppedorappliedwith

impact.BecarefulnottobeinjuredbybrokenglasspiecesincasetheLCDpanelbreaks.

11. Overloading—DonotoverloadACoutletsorextensioncords.Overloadingcancausereorelectricshock.

12. Enteringofobjectsandliquids—Neverinsertanobjectintotheproductthroughventsoropenings.Highvoltageowsin

theproduct,andinsertinganobjectcancauseelectricshockand/orshortinternalparts.

  Forthesamereason,donotspillwaterorliquidontheproduct.

13. Servicing—Donotattempttoservicetheproductyourself.Removingcoverscanexposeyoutohighvoltageandother

dangerousconditions.Requestaqualiedservicepersontoperformservicing.

14. Repair—Ifanyofthefollowingconditionsoccurs,unplugthepowercordfromtheACoutlet,andrequestaqualiedservice

person to perform repairs.

a. Whenthepowercordorplugisdamaged.

b. Whenaliquidwasspilledontheproductorwhenobjectshavefallenintotheproduct.

c. Whentheproducthasbeenexposedtorainorwater.

d. Whentheproductdoesnotoperateproperlyasdescribedintheoperatinginstructions.

 Donottouchthecontrolsotherthanthosedescribedintheoperatinginstructions.Improperadjustmentofcontrols

notdescribedintheinstructionscancausedamage,whichoftenrequiresextensiveadjustmentworkbyaqualied

technician.

  e. Whentheproducthasbeendroppedordamaged.

  f. Whentheproductdisplaysanabnormalcondition.Anynoticeableabnormalityintheproductindicatesthattheproduct

needs servicing.

15. Replacementparts—Incasetheproductneedsreplacementparts,makesurethattheservicepersonusesreplacement

partsspeciedbythemanufacturer,orthosewiththesamecharacteristicsandperformanceastheoriginalparts.Useof

unauthorizedpartscanresultinre,electricshockand/orotherdanger.

16. Safetychecks—Uponcompletionofserviceorrepairwork,requesttheservicetechniciantoperformsafetychecksto

ensure that the product is in proper operating condition.

17. Wallmounting—Whenmountingtheproductonawall,besuretoinstalltheproductaccordingtothemethod

recommended by the manufacturer.

18. Heatsources—Keeptheproductawayfromheatsourcessuchasradiators,heaters,stovesandotherheat-generating

products(includingampliers).

DEAR SHARP CUSTOMER

SAFETY PRECAUTIONS (Continued)

19. Batteries—Incorrectuseofbatteriesmaycausethebatteriestoburstorignite.Aleakybatterymaycorrodetheequipment,

dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:

  •Usethespeciedbatteriesonly.

  •Installthebatterieswithdueattentiontotheplus(+)andminus(-)sidesofthebatteriesaccordingtotheinstructionsinthe

compartment.

  •Donotmixoldandnewbatteries.

  •Donotmixbatteriesofdifferenttypes.Voltagespecicationsofbatteriesofthesameshapemayvary.

  •Replaceanexhaustedbatterywithanewonepromptly.

  •Ifyouwillnotusetheremotecontrolforalongtime,removethebatteries.

  •Ifleakedbatteryuidgetsonyourskinorclothing,rinseimmediatelyandthoroughly.Ifitgetsintoyoureye,batheyour

eyewellratherthanrubbingandseekmedicaltreatmentimmediately.Leakedbatteryuidthatgetsintoyoureyeoryour

clothing may cause a skin irritation or damage your eye.

20. Usageofthemonitormustnotbeaccompaniedbyfatalrisksordangersthat,couldleaddirectlytodeath,personalinjury,

severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and

missile launch control in a weapon system.

21. Donotstayincontactwiththepartsoftheproductthatbecomehotforlongperiodsoftime.Doingsomayresultin

low-temperatureburns.

WARNING:

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be

requiredtotakeadequatecountermeasures.

TomaintaincompliancewithEMCregulations,useshieldedcablestoconnecttothefollowingterminals:PC/AVDVI-Doutput

terminal,PC/AVDVI-Dinputterminal,PC/AVHDMIinputterminal,PCD-SUBinputterminal,PCRGBinputterminals,and

RS-232Cinput/outputterminals.

Ifamonitorisnotpositionedinasufcientlystablelocation,itcanbepotentiallyhazardousduetofalling.Manyinjuries,

particularly to children, can be avoided by taking simple precautions such as:

•Usingxingdeviceslikewallmountbracketsrecommendedbythemanufacturer.

•Onlyusingfurniturethatcansafelysupportthemonitor.

•Ensuringthemonitorisnotoverhangingtheedgeofthesupportingfurniture.

•Notplacingthemonitorontallfurniture(forexample,cupboardsorbookcases)withoutanchoringboththefurnitureandthe

monitor to a suitable support.

•Notstandingthemonitorsonclothorothermaterialsplacedbetweenthemonitorandsupportingfurniture.

•Educatingchildrenaboutthedangersofclimbingonfurnituretoreachthemonitororitscontrols.

Especially for child safety

-Don’tallowchildrentoclimbonorplaywiththemonitor.

-Don’tplacethemonitoronfurniturethatcaneasilybeusedassteps,suchasachestofdrawers.

-Rememberthatchildrencanbecomeexcitedwhilewatchingaprogram,especiallyona“largerthanlife”monitor.Care

should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.

-Careshouldbetakentorouteallcordsandcablesconnectedtothemonitorsothattheycannotbepulledorgrabbedby

curious children.

-TheTFTcolorLCDpanelusedinthismonitorismadewith

theapplicationofhighprecisiontechnology.However,there

may be minute points on the screen where pixels never light

or are permanently lit. Also, if the screen is viewed from

an acute angle there may be uneven colors or brightness.

Please note that these are not malfunctions but common

phenomenaofLCDsandwillnotaffecttheperformanceof

the monitor.

-Donotdisplayastillpictureforalongperiod,asthiscould

cause a residual image.

-Neverrubortapthemonitorwithhardobjects.

-PleaseunderstandthatSHARPCORPORATIONbearsno

responsibility for errors made during use by the customer or

a third party, nor for any other malfunctions or damage to this

product arising during use, except where indemnity liability is

recognizedunderlaw.

-Thismonitoranditsaccessoriesmaybeupgradedwithout

advance notice.

-Donotusethemonitorwherethereisalotofdust,where

humidity is high, or where the monitor may come into contact

withoilorsteam,asthiscouldleadtore.

-Ensurethatthemonitordoesnotcomeintocontactwith

waterorotheruids.Ensurethatnoobjectssuchaspaper

clipsorpinsenterthemonitorasthiscouldleadtoreor

electric shock.

-Donotplacethemonitorontopofunstableobjectsorin

unsafeplaces.Donotallowthemonitortoreceivestrong

shocksortostronglyvibrate.Causingthemonitortofallor

topple over may damage it.

-Donotusethemonitornearheatingequipmentorinplaces

where there is likelihood of high temperature, as this may

leadtogenerationofexcessiveheatandoutbreakofre.

-Donotusethemonitorinplaceswhereitmaybeexposedto

direct sunlight.

-Imagescannotberotatedonthismonitor.

Whenusinginportraitorientation,youwillneedtoprepare

appropriately orientated content in advance.

-TheACoutletshallbeinstalledneartheequipmentandshall

be easily accessible.

The Power Cord

-Useonlythepowercordsuppliedwiththemonitor.

-Donotdamagethepowercordnorplaceheavyobjectson

it, stretch it or over bend it. Also, do not add extension cords.

Damagetothecordmayresultinreorelectricshock.

-Donotusethepowercordwithapowertap.

Addinganextensioncordmayleadtoreasaresultof

overheating.

-Donotremoveorinsertthepowerplugwithwethands.

Doingsocouldresultinelectricshock.

-Unplugthepowercordifitisnotusedforalongtime.

-Donotattempttorepairthepowercordifitisbroken

or malfunctioning. Refer the servicing to the service

representative.

Manual Scope

-Microsoft,WindowsandInternetExplorerareregistered

trademarksofMicrosoftCorporation.

-HDMI,theHDMILogoandHigh-DenitionMultimedia

InterfacearetrademarksorregisteredtrademarksofHDMI

LicensingLLC.

-Adobe,Acrobat,andReaderareeitherregisteredtrademarks

or trademarks of Adobe Systems Incorporated in the United

States and/or other countries.

-ThisproductcomeswithRICOHBitmapFontsproducedand

soldbyRICOHCOMPANY,LTD.

-Allotherbrandandproductnamesaretrademarksor

registered trademarks of their respective holders.

-LanguageofOSDmenuusedinthismanualisEnglishby

way of example.

-Illustrationsinthismanualmaynotexactlyrepresentthe

actual product or display.

-Thismanualassumesuseinlandscapeorientation,except

wherespecicallynoted.

LED Backlight

● TheLEDbacklightinthisproducthasalimitedlifetime.

 *Ifthescreengetsdarkordoesnotturnon,itmaybe

necessarytoreplacetheLEDbacklight.ThisLED

backlight is exclusive to this product and must be replaced

byanauthorizedSHARP servicing dealer or service

center.

 *PleasecontactyourlocalSHARP servicing dealer or

service center for assistance.

TIPS AND SAFETY INSTRUCTIONS

MOUNTING PRECAUTIONS

• Thisproductisforuseindoors.

• AmountingbracketcompliantwithVESAspecicationsis

required.

• Sincethemonitorisheavy,consultyourdealerbefore

installing,removingormovingthemonitor.

• Mountingthemonitoronthewallrequiresspecialexpertise

andtheworkmustbeperformedbyanauthorizedSHARP

dealer.Youshouldneverattempttoperformanyofthis

workyourself.Ourcompanywillbearnoresponsibility

foraccidentsorinjuriescausedbyimpropermountingor

mishandling.

• Usethemonitorwiththesurfaceperpendiculartoalevel

surface.Ifnecessary,themonitormaybetiltedupto20

degreesupwardordownward.

• Thismonitorshouldbeusedatanambienttemperature

between32°F(0°C)and104°F(40°C).Provide

enoughspacearoundthemonitortopreventheatfrom

accumulatinginside.

[5]

2 [5]

7-7/8 [20]

[5]

Unit: inch [cm]

For the monitor in landscape orientation

For the monitor in portrait orientation

7-7/8 [20]

2 [5]

Unit: inch [cm]

*Thismonitorcanbeinstalledclosetoawall.However,as

themonitoremitsheatduringoperation,pleasebeaware

thatthisheatmaydiscolororalterthewall.

• Ifitisdifculttoprovidesufcientspaceforanyreason

suchastheinstallationofthemonitorinsideahousing,or

iftheambienttemperaturemaybeoutsideoftherange

of32°F(0°C)to104°F(40°C),installafanortakeother

measurestokeeptheambienttemperaturewithinthe

requiredrange.

• Temperatureconditionmaychangewhenusingthemonitor

togetherwiththeoptionalequipmentsrecommendedby

SHARP.Insuchcases,pleasecheckthetemperature

conditionspeciedbytheoptionalequipments.

• Donotblockanyventilationopenings.Ifthetemperature

insidethemonitorrises,thiscouldleadtoamalfunction.

• Donotplacethemonitoronadevicewhichgeneratesheat.

• Adheretothefollowingwheninstallingthemonitorinits

portraitorientation.Failingtoadheretothefollowingmay

causemalfunctions.

-InstallthemonitorsuchthatthepowerLEDislocatedon

thebottomside.

-SettheMONITORontheSETUPmenutoPORTRAIT.

(Seepage22.)

-Besuretoclampthepowercord(supplied)ontothecable

clampattachmentusingthesuppliedcableclamp.When

clampingthepowercord,takecarenottostressthe

terminalofthepowercord.Donotbendthepowercord

excessively.

Power cord (Supplied)

Cable clamp

Cable clamp attachment

• Usethesuppliedverticalstickerwhenyouinstallthe

monitorinportraitorientation.

Logo

Operation panel

Donotremovethefactory-afxedstickerbutafxthelogo

stickeroverit.Becarefulnottocovertheremotecontrol

sensororbuttons.

Supplied Components

If any component should be missing, please contact your dealer.



LiquidCrystalDisplayMonitor:1



Remotecontrolunit:1



Cableclamp:2



Powercord:1



R-6battery(“AA”size):2



CD-ROM(UtilityDiskforWindows):1



SetupManual:1



Verticalsticker(Operationpanel):1



Verticalsticker(Logo):1



Terminallabel:1

UsedwheninstallingtheexpansionboardPN-ZB01(optional).



CoverSharplogo:1

PlacethisstickerontotheSHARPlogotocoverthelogo.

* SharpCorporationholdsauthorshiprightstotheUtilityDiskprogram.Donotreproduceitwithoutpermission.

* Forenvironmentalprotection!

 Donotdisposeofbatteriesinhouseholdwaste.Followthedisposalinstructionsforyourarea.

Contents

IMPORTANT INFORMATION ............................................3

DEAR SHARP CUSTOMER ..............................................5

SAFETY PRECAUTIONS ..................................................5

TIPS AND SAFETY INSTRUCTIONS ...............................7

MOUNTING PRECAUTIONS ............................................8

Supplied Components .....................................................9

Part Names .....................................................................10

Connecting Peripheral Equipment ...............................12

ConnectionwithaPCorAVequipment .....................12

ConnectionwhenthePN-ZB01(optional)

is attached .................................................................13

Connecting the Power Cord .........................................14

Binding Cables ...............................................................14

Removing the Handles ..................................................14

Preparing the Remote Control Unit ..............................15

Installing the batteries ................................................15

Remote control operation range .................................15

Turning Power On/Off ....................................................16

Turning on the main power.........................................16

Turning power on/off ..................................................16

Disablingpoweron/offoperations ..............................17

Basic Operation .............................................................18

Menu Items .....................................................................20

Displayingthemenuscreen .......................................20

Menu item details .......................................................21

AdjustmentsforPCscreendisplay ............................28

Initialization (Reset)/Functional Restriction Setting

(FUNCTION) ....................................................................29

Controlling the Monitor with a PC (RS-232C) ..............30

PCconnection ............................................................30

Communicationconditions .........................................30

Communicationprocedure .........................................30

SettingoftheGAMMAuserdata ................................33

RS-232Ccommandtable ...........................................34

Controlling the Monitor with a PC (LAN) .....................42

Settings to connect to a LAN ......................................42

ControllingwithaPC ..................................................44

Troubleshooting .............................................................50

Specications ...............................................................52

Mounting Precautions

(For SHARP dealers and service engineers) ...............56

Front view

2345

1. LCD panel

2. Remote control sensor (Seepage15.)

3. Input switch (Seepage18.)

4. Power switch (Seepage16.)

5. Power LED (Seepage16.)

TIPS

• Useapointedobjectsuchasapentiptopressthe

switches at the front of the monitor.

Part Names

Rear view

13 14

When the PN-ZB01

(optional) is attached

1. Optional attachment section

This section is used to connect optional

hardware for function expansion.

Offering this attachment location is

not a guarantee that future compatible

hardware attachments will be released.

2. Speakers

3. Handles (Seepage14.)

4. Vents

5. Expansion terminal cover

Additional input/output terminals are

availablebyattachingthePN-ZB01

expansion board (optional).

6. PC/AV HDMI input terminal (See page

12.)

7. PC D-sub input terminal (See page

12.)

8. Audio input terminal (Seepage12.)

9. Audio output terminals (Seepage12.)

10. RS-232C output terminal (See page

12.)

11. RS-232C input terminal (Seepage12.)

12. Optional terminal

This terminal is provided for possible

future (optional) function expansion.

Offering of this terminal is not a

guarantee that future expanded

functionality will be provided.

13. AC input terminal (Seepage14.)

14. Main power switch (Seepage16.)

Caution

• ConsultyourSHARPdealerforattachment/detachmentof

optional parts.

• Donotopentheexpansionterminalcoverbyyourself.

There are high voltage parts inside the cover which may

cause an electric shock.

When the PN-ZB01 (optional) is attached

15. PC/AV DVI-D input terminal (Seepage13.)

16. PC/AV DVI-D output terminal (Seepage13.)

17. LAN terminal (Seepage13.)

18. External speaker terminals (Seepage13.)

19. Audio 1 input terminals (Seepage13.)

20. Audio 2 input terminals (Seepage13.)

21. PC RGB input terminals (Seepage13.)

22. AV component input terminals (Seepage13.)

23. AV video input terminal (Seepage13.)

24. AV S-video input terminal (Seepage13.)

Part Names

Remote control unit

1. Signal transmitter

2. POWER button(Seepage16.)

3. MUTE button(Seepage18.)

4. VOL +/- buttons(Seepage18.)

BRIGHT +/- buttons(Seepage18.)

Cursor control (

/ / / ) buttons

5. DISPLAY button(Seepage18.)

6. MODE button(Seepage18.)

7. INPUT button(Seepage18.)

8. MENU button(Seepage18.)

9. SIZE button(Seepage18.)

Connecting Peripheral Equipment

Caution

• Besuretoturnoffthemainpowerswitchanddisconnect

the plug from the power outlet before connecting/

disconnecting cables. Also, read the manual of the

equipmenttobeconnected.

• Becarefulnottoconfusetheinputterminalwiththeoutput

terminal when connecting cables. Accidentally reversing

cables connected to the input and output terminals may

cause malfunctions and the other problems.

TIPS

• Imagesmaynotbedisplayedproperlydependingonthe

computer (video card) to be connected.

• Ascreenwith1920x1080resolutionmaynotbedisplayed

correctlyonPCRGB.Inthiscase,checkthesettingsof

your computer (video card) to verify that input signals

conformtospecicationsofthismonitor.(Seepage54.)

• IfthereisacheckboxtodisableEDIDindisplaycontrol

panel,checkitwhenusingPCRGB.

• UsetheautomaticscreenadjustmentwhenaPCscreen

isdisplayedforthersttimeusingPCD-SUBorPCRGB,

orwhenthesettingofthePCischanged.Thescreenis

adjustedautomaticallywhenSELFADJUSTintheOPTION

menu is set to ON.

• Iftheaudiooutputfromtheplaybackdeviceisconnected

directly to speakers or other devices, the video on the

monitor may appear delayed from the audio portion.

Audio should be played through this monitor by connecting

the playback device to the monitor’s audio input, and

connecting the monitor’s audio output to the speakers or

other devices.

• Theaudioinputterminalsusedineachinputmodeare

factory-setasfollows.

Input mode

Audio input terminal

(Factory setting)

PCD-SUB,PCDVI-D,PCRGB

Audio input terminal

AVDVI-D Audio1inputterminal

AVCOMPONENT(BNC),

AVS-VIDEO,AVVIDEO(BNC)

Audio2 input terminal

AVCOMPONENT(D-SUB),

AV

VIDEO

(D-SUB)

Audio input terminal

PCHDMI,AVHDMI PC/AVHDMIinputterminal

Connection with a PC or AV equipment

1. PC/AV HDMI input terminal

• UseacommerciallyavailableHDMIcable(conformingto

theHDMIstandard).

• SetHDMIofINPUTSELECTontheOPTIONmenu

according to the device to be connected.

• SelecttheaudioinputterminaltobeusedinPCHDMI

orAVHDMIofAUDIOSELECTontheOPTIONmenu.

WhenHDMIisselected,connectiontotheaudioinput

terminal is unnecessary.

2. PC D-sub input terminal

• SetD-SUBofINPUTSELECTontheOPTIONmenu

according to the device to be connected.

• CommonterminalforAVCOMPONENTandAVVIDEO.

• WhenthePN-ZB01(optional)isattached,selecttheaudio

inputterminaltobeusedinPCD-SUBofAUDIOSELECT

on the OPTION menu.

• TousewithAVVIDEO(D-SUB),connectthegreen

terminal to the device’s video output.

3. Audio input terminal

• Useanaudiocablewithoutresistance.

• WhenthePN-ZB01(optional)isattached,settheaudio

inputterminalusedforeachinputmodeinAUDIO

SELECTontheOPTIONmenu.

4. Audio output terminals

• Theoutputsoundvariesdependingontheinputmode.

• Thevolumeoftheoutputsoundcanbexedbysetting

AUDIOOUTPUT(RCA)ontheOPTIONmenu.

• Itisnotpossibletocontrolthesoundoutputfromthe

audiooutputterminalswiththeAUDIOmenu.

5. RS-232C input terminal

RS-232C output terminal

• YoucancontrolthemonitorfromaPCbyconnectinga

commerciallyavailableRS-232straightcablebetween

theseterminalsandthePC.

When the PN-ZB01 (optional) is attached

Connecting Peripheral Equipment

Connection when the PN-ZB01

(optional) is attached

ThePN-ZB01expansionboard(optional)allowstheuseof

additional connection terminals.

6. PC/AV DVI-D input terminal

• SetDVIofINPUTSELECTontheOPTIONmenu

according to the device to be connected.

• SelecttheaudioinputterminaltobeusedinPCDVI-Dor

AVDVI-DofAUDIOSELECTontheOPTIONmenu.

7. PC RGB input terminals

• SetBNCofINPUTSELECTontheOPTIONmenutoPC

RGBwhenusingthePCRGBinputterminals.

• SelecttheaudioinputterminaltobeusedinPCRGBof

AUDIOSELECTontheOPTIONmenu.

8. AV component input terminals

• SetBNCofINPUTSELECTontheOPTIONmenuto

AVCOMPONENTwhenusingtheAVcomponentinput

terminals.

• SelecttheaudioinputterminaltobeusedinAV

COMPONENTofAUDIOSELECTontheOPTIONmenu.

• CannotbeusedwhenD-SUBinINPUTSELECTonthe

OPTIONmenuissettoAVCOMPONENT.

9. AV video input terminal

• SelecttheaudioinputterminaltobeusedinAVVIDEOof

AUDIOSELECTontheOPTIONmenu.

• CannotbeusedwhenD-SUBinINPUTSELECTonthe

OPTIONmenuissettoAVVIDEO.

10. AV S-video input terminal

• SelecttheaudioinputterminaltobeusedinAVS-VIDEO

ofAUDIOSELECTontheOPTIONmenu.

11. Audio1 input terminals / Audio2 input terminals

• Settheaudioinputterminaltobeusedineachinput

modeinAUDIOSELECTontheOPTIONmenu.

12. LAN terminal

• YoucancontrolthemonitorfromaPConanetworkby

connecting a commercially available LAN cable between

this terminal and a network.

13. External speaker terminals

• Touseexternalspeakers,setSPEAKERSELECTonthe

SETUPmenutoEXTERNAL.

• Besuretouseexternalspeakerswithanimpedanceof6Ω

orgreaterandaratedinputofatleast7W.

132

Approx.

3-15/16 inch

(10 cm)

1.Attachaspeakercablecore(includedwiththePN-ZB01)to

the end of the speaker cable connected to the monitor.

2.Whilepushingthetab,insertthetipofthecable.

3. Release the tab.

TIPS

• Besuretoconnectthe+and-terminalsandtheleftand

right speakers properly.

• Avoidshortcircuitingthe+and-terminals.

• WhenSPEAKERSELECTissettoEXTERNAL,the

internal speakers are disabled.

14. PC/AV DVI-D output terminal

• ThevideoofthePC/AVDVI-Dinputcanbeoutputtoan

external device.

• OutputtingHDCP-encryptedvideorequiresanexternal

devicewhichsupportsHDCP.

• Thisterminalallowsthedaisychainconnectionofupto5

monitors.

TIPS

• Thelengthofthesignalcablesorsurroundingenvironment

mayaffecttheimagequality.

• Thescreenmaynotdisplayproperlywhenusingterminals

otherthanPCDVI-D/AVDVI-Dfortheinputmode.Inthis

case, turn off the power to all the monitors connected in a

daisy chain and then turn the power on again.

• WhenconnectingmonitorsinadaisychainsetAUTO

INPUTCHANGEtoOFF.

• Videooutputisdisabledinthefollowingcases:

Whenthepoweristurnedoff

Whenthemonitorisininputsignalwaitingmode

Connecting the Power Cord

Caution

• Useonlythepowercordsuppliedwiththemonitor.

1.Turnoffthemainpowerswitch.

2.Plugthepowercord(supplied)intotheACinputterminal.

3.Plugthepowercord(supplied)intotheACpoweroutlet.

Binding Cables

The cables connected to the terminals on the rear of the

monitor can be fastened with the cable clamp.

Insert the cable clamp into the cable clamp attachment on the

rear of the monitor and fasten the cables.

AC input terminal

Main power switch

Power cord (Supplied)

For power

outlet

Removing the Handles

The installation position can be changed.

Cable clamp

attachment

Cable

The handles can be removed.

Handle

Handle screws

Caution

• Theremovablehandlesandhandlescrewsareforusewiththismonitor.Donotusethemforanyotherdevices.

• Toattachhandles,besuretousethehandlesandhandlescrewswhichwereremovedfromthemonitor.

• Besurethehandlesareattachedsecurely.

Preparing the Remote Control Unit

Installing the batteries

1. Pressthecovergentlyandslideitinthedirectionofthe

arrow.

2. See the instructions in the compartment and put in the

suppliedbatteries(R-6(“AA”size)x2)withtheirplus(+)

andminus(-)sidesorientedcorrectly.

3. Closethecover.

TIPS

• Whenthebatteriesbecomeexhausted,replacethemwith

new (commercially available) batteries.

• Thesuppliedbatteries(R-6(“AA”size)x2)maybecome

exhaustedquicklydependingonhowtheyarestored.

• Ifyouwillnotbeusingtheremotecontrolforalongtime,

remove the batteries.

• Usemanganeseoralkalinebatteriesonly.

Remote control operation range

Theoperationrangeoftheremotecontrolunitisapprox.16.4

feet(5m)atanangleofapprox10°fromthecentertothetop/

bottom/right/left of the remote control sensor.

10°10°

10°

Remote

control sensor

16.4

feet

(5 m)

TIPS

• Donotexposetheremotecontrolunittoshockbydropping

or stepping on it. This could lead to a malfunction.

• Donotexposetheremotecontrolunittoliquids,anddonot

place it in an area with high humidity.

• Theremotecontrolunitmaynotworkproperlyiftheremote

control sensor is under direct sunlight or strong lighting.

• Objectsbetweentheremotecontrolunitandtheremote

control sensor may prevent proper operation.

• Replacethebatterieswhentheyrunlowasthismay

shorten the remote control’s operation range.

• Ifauorescentlightisilluminatedneartheremotecontrol

unit, it may interfere with proper operation.

• Donotuseitwiththeremotecontrolofotherequipment

such as air conditioner, stereo components, etc.

Caution

• TurnonthemonitorrstbeforeturningonthePCor

playback device.

Turning on the main power

Main power switch

Caution

• Themainpowermustbeturnedon/offwiththemainpower

switch.Donotconnect/disconnectthepowercordorturn

the breaker on/off while the main power switch is on.

• WhenswitchingthemainpowerswitchorthePOWER

buttonoffandbackon,alwayswaitforatleast5seconds.

• Foracompleteelectricaldisconnection,pulloutthemain

plug.

Turning Power On/Off

Turning power on/off

PressthePOWERbuttonorPOWERswitchtoturnthepower

ON/OFF.

Power LED

Status Status of the monitor

Greenlit Power on

Orange lit Power off (Standby mode)

Greenashing Input signal waiting mode

Caution

• WhenswitchingthemainpowerswitchorthePOWER

buttonoffandbackon,alwayswaitforatleast5seconds.

A short interval may result in a malfunction.

TIPS

• Whenthemainpowerswitchisoff,themonitorcannotbe

turned on.

• Ifthemonitorisintheinputsignalstandbymodeandyou

pressthePOWERbuttonontheremotecontrolunit,the

monitor enters standby mode.

• SettingtheSCHEDULEashesthepowerLEDalternately

in red and orange in standby mode.

• Todisablethelogoscreenfromdisplayingwhenturning

thepowerON,setLOGOSCREENtoOFFontheSETUP

menu. (See page 23.)

Turning Power On/Off

Date/time setting

• Ifthetimehasyettobesetwhenthemonitorisrstturned

on, the date/time setting screen appears. Set the date and

time.

DATE/TIME SETTING

SET

CANCEL

OK···[MENU]

: :

01 01 11

12 AM00

:/ 20

1. Press , , or to select the date and

time, and press

or to change the numerical

values.

2. Press

or toselectSETandthenpress

• Besuretosetthedateandtime.

• Thedate/timesettingscreenwillcloseautomaticallyifno

operationisperformedforabout15seconds.Thedate

andtimecanbesetusingDATE/TIMESETTINGfrom

the OPTION menu when the date/time setting screen

disappears.

TIPS

•

Setthedatein“Month/Day/Year”order.

•

Setthetimeona12-hourbasis.

•

The clock is maintained by the internal battery.

•

If you already set the time but the date/time setting

screen appears when the power is turned on, the

internal battery may be exhausted. Please contact

your local SHARP servicing dealer or service center for

assistance with battery replacement.

•

Estimatedservicelifeoftheinternalbattery:About5

years (depending on monitor operation)

•

The initial battery was inserted at the factory when the

monitor was shipped, so it may run out of power before

its expected operation life.

Disabling power on/off operations

Power on/power off operations can be disabled in order to

protect the monitor from an accidental power off. Set the

ADJUSTMENTLOCKinFUNCTIONmenuto“ON2”.(See

page 29.)

Basic Operation

1. INPUT (Input mode selection)

The menu is displayed. Press

or to select the input

mode, and press

to enter.

* You can select the input terminal by pressing the input

switch of the monitor.

Input mode Video Audio

PC D-SUB PC D-sub input terminal

Audio input terminal

PC HDMI

PC/AV HDMI input terminal

AV HDMI

PC/AV HDMI input terminal

AV COMPONENT PC D-sub input terminal

Audio input terminal

AV VIDEO PC D-sub input terminal

When the PN-ZB01 (optional) is attached

Input mode Video Audio

PC DVI-D

PC/AV DVI-D input terminal

PC HDMI

PC/AV HDMI input terminal

PC D-SUB PC D-sub input terminal

PC RGB PC RGB input terminals

AV DVI-D

PC/AV DVI-D input terminal

AV HDMI

PC/AV HDMI input terminal

AV COMPONENT

AV COMPONENT input

terminals

PC D-sub input terminal

AV S-VIDEO AV S-video input terminal

AV VIDEO

AV video input terminal

PC D-sub input terminal

*1 Select the terminal to be used in D-SUB of INPUT

SELECT. (See page 23.)

*2 Select the terminal to be used in HDMI of INPUT SELECT.

(See page 23.)

*3 Select the terminal for AUDIO SELECT which is used for

audio input. (See page 23.)

*4 Select the terminal to be used in DVI of INPUT SELECT.

(See page 23.)

*5 Select the terminal to be used in BNC of INPUT SELECT.

(See page 23.)

2. MUTE

Turns off the volume temporarily.

Press the MUTE button again to turn the sound back to the

previous level.

3. MENU

Displays and turns off the menu screen. (see page 20.)

4. VOL +/- (Volume adjustment)

Pressing

or displays the VOLUME menu when the

menu screen is not displayed.

V OLUME 15

Press or to adjust the volume of the sound.

* If you do not press any buttons for about 4 seconds, the

VOLUME menu automatically disappears.

5. BRIGHT +/- (Backlight adjustment)

Pressing

or displays the BRIGHT menu when the

menu screen is not displayed.

BRIGHT 15

Press

or to adjust the brightness.

* If you do not press any buttons for about 4 seconds, the

BRIGHT menu automatically disappears.

6. SIZE (Screen size selection)

The menu is displayed.

Press

or to select the screen size. (See page 19.)

7. DISPLAY

Displays monitor information. When you press this button

again, the display disappears.

When the PN-ZB01 (optional) is attached, the display changes

from INFORMATION1 → INFORMATION2 → clear display,

and so on every time you press this button.

• The display disappears automatically after about 15

seconds.

•

LAN

is displayed during LAN communication.

• If

LAN

is displayed in red, there is a duplicate IP address.

8. MODE (Color mode selection)

Each time you press this button, the color mode changes in

the following order:

STD (Standard) → VIVID → sRGB →

HIGH ILLUMINANCE → STD...

• HIGH ILLUMINANCE is a display with colors suited to

bright locations.

• sRGB applies to PC input only.

sRGB is international standard of color representation

specied by IEC (International Electrotechnical

Commission). Color conversion is made in taking account

of liquid crystal’s characteristics and represents color tone

close to its original image.

Basic Operation

Switching the screen size

Evenwhenthescreensizeischanged,thedisplaymayremainthesamedependingontheinputsignal.

WIDE PCinput Displaysimagesoitllstheentirescreen.

AVinput Animagewitha4:3aspectratioisstretchedtolltheentire

screen.

ZOOM 1

PCinput Animagewitha4:3aspectratioisenlargedtolltheentirescreen

without changing the aspect ratio. The edges of the image may be

cut off.

AVinput

ZOOM 2

PCinput UsethissizeifZOOM1cutsoffthesubtitles.

AVinput

NORMAL

PCinput Displaysimagesoitllsthescreenwithoutchangingtheaspect

ratio of the input signals.

AVinput Displaystheentireimageoftheaspectratioof4:3without

changing the aspect ratio.

Dot by Dot

PCinput DisplaysthedotsofthesignalsinputfromtheconnectedPCas

the corresponding dots on the screen.

AVinput Displaysthedotsoftheinputsignalsasthecorrespondingdotson

the screen.

TIPS

• Usingthismonitor’sscreen-sizeswitchingordual-screendisplayfunctionstocompressorexpandthescreenforcommercial

orpublicviewinginestablishmentslikecafesorhotelsmayinfringeontherightsofthecreators,asprotectedbyCopyright

Law, so please be careful.

• When“Enlarge”isset,thescreensizeisxedto“WIDE”mode.

• Whendual-screendisplayisselected,thescreensizecannotbechanged.

• Theappearanceoftheoriginalvideomaychangeifyouselectascreensizewithadifferentaspectratiothantheoriginal

image(e.g.TVbroadcastorvideoinputfromexternalequipment).

• Whenanordinarynon-wideimage(4:3)isviewedwiththewholescreenusingthescreen-sizeswitchingfunctionofthis

monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen

sizeto“NORMAL”.

• Whenplayingcommercialsoftware,partsoftheimage(likesubtitles)maybecropped.Inthiscaseselecttheoptimalscreen

sizeusingthescreen-sizeswitchingfunctionofthismonitor.Withsomesoftware,theremaybenoiseordistortionatthe

edges of the screen. This is due to the characteristics of the software, and is not a malfunction.

• Dependingontheoriginalimagesize,blackbandsmayremainattheedgesofthescreen.

Menu Items

Displaying the menu screen

Video and audio adjustment and settings of various functions

are enabled. This section describes how to use the menu

items. See pages 21 to 25 for details of each menu items.

Caution

• Donotturnthemainpowerswitchoffwhilethemenuitems

arebeingdisplayed.Doingsomayinitializethesettings.

Example of operation

(Adjusting CONTRAST in the PICTURE menu)

1. Press

to display the menu screen.

1 920x1080

V: 60 Hz H: 67.5 kHz

AUTO

CLOCK

PHASE

H-POS

V-POS

H-SIZE

V-SIZE

H-RESOLUTION

V-RESOLUTION

RESET

SCREEN

PICTURE

AUDIO

SETUP

OPTION

PIP/PbyP

MULTI

600

610

1920

1080

SCREEN

1/1

END···[MENU]

PC D-SUB

2. Press

to select PICTURE, and press

3. Press

to select CONTRAST.

AUTO

ANALOG GAIN

ANALOG OFFSET

BRIGHT

CONTRAST

BLACK LEVEL

TINT

COLORS

SHARPNESS

RGB INPUT RANGE

1/2

FULL

PC D-SUB

PICTURE

SCREEN

PICTURE

AUDIO

SETUP

OPTION

PIP/PbyP

MULTI

OK···[MENU]MOVE OSD···[DISPLAY]

1 920x1080

V: 60 Hz H: 67.5 kHz

4. Press or

to adjust the setting.

▲

AUTO

ANALOG GAIN

ANALOG OFFSET

BRIGHT

CONTRAST

BLACK LEVEL

TINT

COLORS

SHARPNESS

RGB INPUT RANGE

1/2

FULL

PC D-SUB

PICTURE

SCREEN

PICTURE

AUDI

OPTION

PIP/PbyP

MULTI

SETUP

OK···[MENU]MOVE OSD···[DISPLAY]

1 920x1080

V: 60 Hz H: 67.5 kHz

For items that have , press , make settings and then

press

5. Press

twice to close the menu screen.

TIPS

• Themenuwilldifferdependingontheinputmode.

• Themenuscreenwillcloseautomaticallyifnooperationis

performedforabout15seconds.(DATE/TIMESETTING,

SCHEDULEandLANSETUPscreenswillcloseinabout4

minutes.)

Menu screen display

▲

AUTO

ANALOG GAIN

ANALOG OFFSET

BRIGHT

CONTRAST

BLACK LEVEL

TINT

COLORS

SHARPNESS

RGB INPUT RANGE

1/2

FULL

PC D-SUB

SCREEN

PICTURE

AUDIO

SETUP

OPTION

PIP/PbyP

MULTI

PICTURE

OK···[MENU]MOVE OSD···[DISPLAY]

1920x1080

V: 60 Hz H: 67.5 kHz

1 Name of the menu

2 Input mode

3 An item being selected (highlighted)

4 Screenresolutionofinputsignal,andotherdata.

TIPS

• Itemsthatcannotbeselectedappearingray.

(e.g. Function not supported by the current input signal)

Menu Items

The displayed menu items vary depending on whether or not

the PN-ZB01 (optional) is attached.

The following menus will be displayed only when the PN-ZB01

(optional) is attached.

Menu Item

SETUP HOTPLUGCONTROL DVI

RS-232C/LANSELECT

LANSETUP

AUTOASSIGNFIXEDIPADDR.

SPEAKERSELECT

OPTION INPUTSELECT DVI

BNC

AUDIOSELECT PCDVI-D

PCD-SUB

PCRGB

AVDVI-D

AVCOMPONENT(BNC)

AVCOMPONENT(D-SUB)

AVS-VIDEO

AVVIDEO(BNC)

AVVIDEO(D-SUB)

PIP/PbyP PIP SOURCE

Menu item details

The menu will differ depending on the input mode.

SCREEN

You can move the menu screen display position each time

DISPLAY

is pressed.

AUTO (PC D-SUB/PC RGB)

TheCLOCK,PHASE,H-POS,andV-POSareautomatically

adjusted.

Pressing

performsadjustment.

UsethisautomaticadjustmentwhenyouusethePCD-sub

inputterminalorPCRGBinputterminalstodisplayaPC

screenforthersttimeorwhenyouchangethesettingof

thePC.(Seepage 28.)

CLOCK (PC D-SUB/PC RGB)

Adjustsfrequencyfor sampling clock for applicable video.

Adjustwhenthereisickeringintheformofverticalstripes.

Whenusingtheadjustmentpattern(seepage28),make

adjustmentssothatno vertical stripe noise appears in it.

PHASE (PC D-SUB/PC RGB)

Adjustssamplingclockphaseforapplicablevideo.

Useful when small characters appear with low contrast and/

orthereareickersatcorners.

Whenusingtheadjustmentpattern(seepage28),make

adjustmentssothatnohorizontalstripenoiseappearsinit.

* AdjustmentstoPHASEshouldbemadeonlyafterCLOCK

has been correctly set.

H-POS

Adjustthehorizontalpositionoftheimage.

V-POS

Adjusttheverticalpositionoftheimage.

H-SIZE

Adjustthehorizontalsizeoftheimage.

V-SIZE

Adjusttheverticalsizeoftheimage.

H-RESOLUTION (PC D-SUB/PC RGB)

Sets properhorizontalresolutionwhentheresolutionof

inputsignalsisnotrecognizedproperly.(Adjustmentmaybe

impossible with some signals.)

V-RESOLUTION (PC D-SUB/PC RGB)

Sets proper vertical resolution when the resolution of input

signalsisnotrecognizedproperly.(Adjustmentmaybe

impossible with some signals.)

RESET

ResetsthevaluesoftheSCREENmenuitemstothefactory

preset values.

Select “ON” and then press

PICTURE

You can move the menu screen display position each time

DISPLAY

is pressed.

AUTO (PC D-SUB/PC RGB)

The ANALOGGAINandANALOGOFFSETare

automaticallyadjusted.

Pressing

performsadjustment.

ANALOG GAIN (PC D-SUB/PC RGB)

Adjuststhebrightportionsofthevideoinputsignal.

ANALOG OFFSET (PC D-SUB/PC RGB)

Adjuststhedarkportionsofthevideoinputsignal.

BRIGHT

Adjuststhebacklightbrightness.(InPIPmode,themainside

settingisreectedintheimage.)

CONTRAST

Adjuststhedifferencebetweenthebrightanddarkportions

of the image.

BLACK LEVEL

Adjuststheentirebrightnessofthevideosignals.

TINT

Adjuststhehue.Selecting+changesthecolortowards

green,andselecting-changesittowardsmagenta.

COLORS

Adjuststhecolorintensity.

SHARPNESS

Adjuststhesharpnessoftheimage.

RGB INPUT RANGE (PC DVI-D/PC HDMI/PC D-SUB/PC

RGB/AV DVI-D/AV HDMI)

SetstheRGBinputsignalrange.WhenusingHDMIsetto

AUTO,theRGBinputsignalisdetectedautomatically.Use

AUTO normally.

IftheRGBinputsignalrangecannotbesetappropriately

evenwhenusingAUTO,setaccordingtotheimage.When

the setting is different, images will be displayed with washed

out blacks and compressed gradients.

ADVANCED (AV input)

Youcanadjustmorespecically.(Seepage28.)

COLOR MODE

Changes the color mode on the screen. The color mode on

the screen can also be changed using a remote control unit.

(Seepage18.)

* sRGBisPCinputonly.Seepage18fordetails.

(InPIPmode,themainsidesettingisreectedintheimage.)

WHITE BALANCE

THRU .............. Displaystheinputsignallevelasis.(forPC

DVI-D/PCHDMIonly)

PRESET ......... SelectsthecolortemperatureusingPRESET.

USER .............. UsedforadjustingR-/G-/B-CONTRASTand

R-/G-/B-OFFSETrespectively.

(InPIPmode,themainsidesettingisreectedintheimage.)

PRESET

SelectsthecolortemperaturewhentheWHITEBALANCEis

settoPRESET.

The setting values are shown for reference. The color

temperature of the screen varies over time.

This function is not intended to keep the color temperature

constant.

Menu Items

USER

AdjustseachitemwhentheWHITEBALANCEissetto

USER.

R-CONTRAST ....Adjustsbright-tonedredcomponent.

G-CONTRAST ....Adjustsbright-tonedgreencomponent.

B-CONTRAST ....Adjustsbright-tonedbluecomponent.

R-OFFSET ..........Adjustsdark-tonedredcomponent.

G-OFFSET .........Adjustsdark-tonedgreencomponent.

B-OFFSET ..........Adjustsdark-tonedbluecomponent.

COPY TO USER

CopiesthevalueofwhitesetforPRESETtotheUSER

setting.

Select “ON” and then press

(In the case other than white, color tone may differ from the

PRESET.)

GAMMA

Selectsthegamma.USERsetsthegammatothesent

value (see page 33). (In PIP mode, the main side setting is

reectedintheimage.)

DISPLAY COLOR PATTERN

Displaysacolorpattern.Canbedisplayedwhilethemenu

screen is displayed, so you can refer to the pattern while

adjustingtheimage.

OFF ..............No pattern display.

WHITE ..........Whitesinglecolorpatterndisplay.

RED ..............Red single color pattern display.

GREEN .........Greensinglecolorpatterndisplay.

BLUE ............Bluesinglecolorpatterndisplay.

USER............Red/green/blue mixed color pattern display.

WhenUSERisselected,seteachcolor’s

level.

RESET

ResetsthevaluesofthePICTUREmenuitemstothefactory

preset values.

Select “ON” and then press

AUDIO

TREBLE

Adjuststhevolumeoftreble-levelsound.

BASS

Adjuststhevolumeofbass-levelsound.

BALANCE

Adjuststhebalanceoftheaudiosoundbetweenrightandleft.

RESET

ResetsthevaluesoftheAUDIOmenuitemstothefactorypresetvalues.

Select “ON” and then press

SETUP

OSD H-POSITION

Adjuststhehorizontaldisplaypositionofmenuscreen.

OSD V-POSITION

Adjuststheverticaldisplaypositionofmenuscreen.

SCREEN MOTION

Residual images are reduced by moving the screen.

PATTERN1 ......... The whole screen moves vertically and

horizontally.

PATTERN2 ......... A black screen spreads from the bottom of

the screen and then shrinks to the bottom

of the screen. If the monitor is installed

in the portrait orientation, a black screen

spreads from the left end of the screen and

then shrinks to the left end of the screen.

PATTERN3 ......... A black bar moves from the left end to the

right end of the screen. If the monitor is

installed in the portrait orientation, a black

bar moves from the top to the bottom of

the screen.

PATTERN4 .........Blackscreensappearfromboththe

top and bottom of the screen, and the

displayed image is compressed into the

centraleld.Ifthemonitorisinstalled

in the portrait orientation, the screen is

compressed from the left and right ends.

PATTERN1 PATTERN2

PATTERN4PATTERN3

MOTION TIME 1

Specifyatimeperiod(operatinginterval)untilSCREEN

MOTION starts.

MOTION TIME 2

SpecifyatimeperiodduringwhichSCREENMOTION

operates (time period during which the screen will move).

MONITOR

Select the installation direction of the monitor.

LANDSCAPE ............Landscape orientation

PORTRAIT ...............Portrait orientation

MONAURAL AUDIO

Outputs audio signals as monaural.

LANGUAGE

Sets the display language for the menu screen.

POWER ON DELAY

You can delay the screen display after the monitor is turned

on.Theperiodcanbesetupto60secondsinunitsofone

second.Whenthisfunctionisactivated,thepowerLED

ashes(atapprox.1secondinterval)inorange.Thisfunction

isdisabledwhen0isspecied.

Menu Items

COPY SETTING VALUE

Whenthemonitorhasbeenconnectedtomultiplemonitors

byRS-232C,thesettingsinthemonitorcanbecopiedtothe

monitorconnectedtotheRS-232Coutputterminalandto

the daisy chain of connected monitors that follows.

SelectsthesettingstocopywithCOPYSETTINGVALUE

TARGET.

“PICTURE”ONLY .....CopiesthePICTUREmenusettings.*

ALL ...........................Copiesallthesettings.*

SelecttheIDNo.ofthemonitorthatyouwouldlikecopyto

withCOPYTOIDNo.,thenselectCOPYandpress

If you select ALL, settings will be copied to all monitors.

WhenyouwouldliketoconrmtheIDNo.thatissettothe

monitor,selectIDNo.DISPLAYandpress

.TheIDNo.

will be displayed on the screen.

*CertainsettingdetailssuchasANALOGGAIN,ANALOG

OFFSET,andDISPLAYCOLORPATTERNcannotbe

copied.

LOGO SCREEN

Sets whether or not to display the logo screen.

OPTION

DATE/TIME SETTING

Set the date and time. Press

to select the date

and time, and press

to change the numerical

values.

Setthedatein“Month/Day/Year”order.

Setthetimeona12-hourbasis.(Factorydefault)

DATE/TIME FORMAT

Sets the date/time display format.

DATE ..................MM/DD/YYYY

DD/MM/YYYY

YYYY/MM/DD

(YYYY:Year,MM:Month,DD:Day)

TIME ...................Select12-or24-hourtime.

SCHEDULE (See page 27.)

You can turn the power on/off and change the screen

brightnessataspeciedtime.

INPUT SELECT

SelecttheinputmodetobeusedinPCD-Subinputterminal,

PC/AVDVI-Dinputterminal,PC/AVHDMIinputterminaland

PCRGB/AVcomponentinputterminals.

ForD-SUB,selectSETafterselectingtheinputmode,and

then

press

D-SUBandBNCcannotbesettoAVCOMPONENTatthe

same time.

IfD-SUBissettoAVVIDEO,theAVVIDEOinputterminal

cannotbeusedforBNC.

AUDIO SELECT

Selects the terminal used to input audio signals in each input

mode.

INPUT SIGNAL (PC D-SUB/PC RGB)

IfacomputerconnectedtothePCD-sub/PCRGBinput

terminal outputs any of the following resolutions, make a

selection from the following options.

480LINES ..........AUTO,640x480or848x480

768LINES ..........AUTO,1024x768,1280x768,or1360x768

1050LINES ........1400x1050or1680x1050

ZOOM2SPECIALSETTING(See page 26.)

STANDBY MODE

WhenSTANDARDisselected,startuptimefromstandby

mode is reduced. Note, however that, more power will be

consumed in standby mode.

WhenLOWPOWERisselected,currentconsumption

is reduced while the monitor is in standby mode. Note,

however, that the startup time from standby mode becomes

longer.

IfsettoLOWPOWER,certainRS-232Ccommandscannot

be used in standby mode, and control via LAN will be

disabled.

OFF IF NO OPERATION

Determineswhetherornottosetthemonitortogointo

standby mode when there is no operation from the remote

controlunit,RS-232Ccommands,orLANforover4hours.

HOT PLUG CONTROL

SetswhethertousehotplugcontrolforthePC/AVHDMI

andPC/AVDVI-Dinputterminals.

RS-232C/LAN SELECT

Selects the method with which to control the monitor from

the computer.

ID No. SET

AssignsIDnumberstomonitorsconnectedinadaisychain

(seepage31),usingtheRS-232cables.

Thenumbers1to255areavailableforIDnumbers.

If“0”isset,thesystemregardsthisasthestatewherenoID

number is set.

AUTO ASSIGN ID No.

IDNo.tobeusedwillbeautomaticallyassignedwhen

multiplemonitorsareconnectedwithRS-232C.

Select ON, then press

Performoperationsusingtherstmonitorinthedaisychain.

BAUD RATE

SelectsthecommunicationspeedusedforRS-232C

communication.

LAN SETUP

Conguresthesettingstocontrolthemonitorfromthe

computer via LAN. (See page 42.)

AUTO ASSIGN FIXED IP ADDR.

CanbeenabledwhenRS-232C/LANSELECTisLANand

theDHCPCLIENTisOFF.

SetDHCPCLIENTtoOFFforthemonitorconnectedtothe

RS-232Coutputterminalandthedaisychainofconnected

monitorsthatfollows.FixedIPaddressesareautomatically

allocated.

If the IP address is a duplicate with a network device other

than a monitor, individually change the IP address.

SPEAKER SELECT

Selects the speaker to be used.

HDMI AUTO VIEW

WhenONisselected,thescreensizeisadjusted

automaticallyaccordingtothescreensizecontrolsignal

includedinthevideosignalinputfromtheAVHDMIinput

terminal.

Menu Items

SCAN MODE (AV input)

SetsthescanmodeusedforAVmodeinput.

MODE1 ...............Over-scandisplay

MODE2 ...............Under-scandisplay

MODE3 ...............Under-scandisplaywhentheinputsignal

is1080i/p.Otherwise,over-scandisplay

*

EvenwhenMODE1isselected,under-scandisplayisusedwhen

theinputsignalis1080i/pandthescreensizeisDotbyDot.

POWER MANAGEMENT

POWERMANAGEMENTdetermineswhetherornotto

switch modes from no signal to the input signal standby

mode.

COLOR SYSTEM (AV S-VIDEO/AV VIDEO)

SelectthecolorsystemoftheAVequipmentwhichis

connectedtoAVS-videoandAVvideoinputterminal.(AUTO

/PAL/PAL-60/SECAM/NTSC3.58/NTSC4.43)

WhenAUTOisselected,thecolorsystemisautomatically

set according to the input signal.

AUDIO OUTPUT (RCA)

Sets the volume of sound output from the audio output

terminals.

WhensettoVARIABLE2,soundwillnotbeoutputfromthe

built-inspeakerortheexternalspeakerterminal.

VARIABLE1 ........ YoucanadjustthevolumeusingVOLUME.

VARIABLE2 ........ YoucanadjustthevolumeusingVOLUME.

FIXED .................Fixesthesounds.

AUDIO LEVEL (STEREO MINI)

Selects the maximum audio input level of the audio input

terminal.

SELF ADJUST

On a PCD-SUB/PCRGB screen, specify whether to

performscreenadjustmentautomaticallyornot.WhenON

isselected,thescreenisautomaticallyadjustedwhenits

resolutionis800x600orhigherandthetimingofinput

signalschanges.“ADJUSTING”appearsonthescreen

duringtheadjustment.Forimageswithblackedges,etc.,

dependingonthesignal,adjustmentmaynotbepossible.

InthiscaseselectOFF.(Performmanualadjustmentofthe

screen.)

AUTO INPUT CHANGE

Specifywhethertochangeinputsautomatically.WhenONis

selected and no signal is present in the selected input mode,

AUTOINPUTCHANGEautomaticallychangestheselected

mode to another mode where a video signal is present.

Whenvideosignalsexistinmultipleinputmodes,the

switching priority is as follows:

PCD-SUB,PCHDMI,AVHDMI,AVCOMPONENTandAV

VIDEO

WhenthePN-ZB01(optional)isattached:

PCDVI-D,PCHDMI,PCD-SUB,PCRGB,AVDVI-D,AV

HDMI,AVCOMPONENT,AVS-VIDEOandAVVIDEO

(Inputmodeswitchingmaytake15secondsormore,

dependingontheconnectedequipment.Inputsignals

may not be detected properly and a priority may change,

dependingontheconnectedequipmentorvideosignals.)

MULTI

ENLARGE (See page 26.)

Sets whether or not to use the enlarge function.

ADVANCED (ENLARGE)

ENLARGEH/ENLARGEV

......... Sets the number of screen splits (number of

monitors)inthehorizontal/verticaldirectionusedfor

the enlargement.

ENLARGE-POS

......... Specify the split screen to be displayed when the

enlargement function is used.

H-POS/V-POS

.........Adjustthehorizontal/verticalpositionofthe

enlarged screen.

BEZEL ADJUST

Sets whether or not to use the frame correction function.

ADVANCED (BEZEL ADJUST)

BEZELADJUST(TOP)/BEZELADJUST(BOTTOM)/

BEZELADJUST(RIGHT)/BEZELADJUST(LEFT)

.........Adjustssothatthetop/bottom/left/rightconnecting

jointsofgroupedunitswillbedisplayedsmoothly

when a group of monitors are aligned in multiples to

display a single image.

BEZEL(TOP)/BEZEL(BOTTOM)/BEZEL(RIGHT)/

BEZEL(LEFT)

......... Sets the frame width of the display.

Menu Items

PIP/PbyP

PIP MODES

Sets the display method.

OFF .........Displays one screen.

PIP ...........Displays a sub screen inside a main screen.

PbyP ........Displays a main screen and a sub screen in a line.

PbyP2 ......

Displays a main screen which measures 1280 pixels

in the longest direction and a sub screen in a line.

PIP SIZE

Sets the size of the sub screen in PIP mode.

PIP H-POS

Adjusts the horizontal position of the sub screen in PIP mode.

PIP V-POS

Adjusts the vertical position of the sub screen in PIP mode.

PIP BLEND

In PIP mode, use this menu item to display the sub screen

transparently.

PIP SOURCE

Selects the input signal of the sub screen in PIP, PbyP, or

PbyP2 mode.

SOUND CHANGE

Sets the sound which is output in PIP, PbyP, or PbyP2 mode.

If the main screen is displayed as a full screen by the AUTO

OFF function, the sound for the main screen is output even

when the sound for the sub screen is specied.

MAIN POS

Sets the position of the main screen in PbyP or PbyP2 mode.

PbyP2 POS

Sets the position of the sub screen in PbyP2 mode.

AUTO OFF

Sets the display method when no signals for the sub screen

are input in PIP, PbyP, or PbyP2 mode.

MANUAL .......

Displays a main screen and a black sub screen.

AUTO ............ Displays the main screen as a full screen.

TIPS

• When WHITE BALANCE is set to THRU, BLACK LEVEL,

CONTRAST, TINT, COLORS, RGB INPUT RANGE,

GAMMA and COPY TO USER cannot be set.

• If COLOR MODE is set to sRGB, the following items cannot

be set.

WHITE BALANCE, PRESET, USER, COPY TO USER, and

GAMMA

• When the COLOR MODE is set to VIVID or HIGH

ILLUMINANCE, GAMMA can not be adjusted.

• STANDBY MODE cannot be set to LOW POWER when

SCHEDULE is effective or when OFF is selected for LED in

FUNCTION.

• When displaying the color pattern, it is possible to adjust

certain items of the PICTURE menu.

Non-adjustable items cannot be selected.

Audio input from the HDMI input terminal is also not output.

Dual screen display

You can display the screens of the PC input signal and AV

input signal simultaneously.

Set this function with “PIP MODES” in the PIP/PbyP menu.

PIP

Main screen

Sub

screen

A sub screen is displayed

inside a main screen.

PbyP

Main

screen

Sub

screen

A main screen and a sub

screen are displayed in a

line.

PbyP2

Main screen

Sub

screen

Displays a main screen

which measures 1280

pixels in the longest

direction and a sub

screen in a line.

* The currently selected input signal is displayed on the main

screen.

* You cannot simultaneously display the screens of signals

of the same type, such as two types of PC input signals or

two types of AV input signals.

* The dual screen display cannot be used with the

combination of PC DVI-D and AV HDMI or of AV DVI-D and

PC HDMI.

TIPS

• You might infringe on a copyright of the author which is

protected by copyright law when you display the images of

the computer screen and television/VCR simultaneously for

prot-making or to show the image to the public.

• The screen size for dual-screen display is the same as

the screen size for single-screen display. The Dot by Dot

screen is displayed in NORMAL size except when it is set

as the PIP main screen.

• When dual-screen display is selected, the SCREEN

MOTION function is disabled.

• When dual-screen display is selected, the AUTO INPUT

CHANGE function is disabled.

• When dual-screen display is selected, the screen cannot

be enlarged.

• When dual-screen display is selected, the INPUT SELECT

options cannot be set.

• When an interlaced signal (1080i, 480i, video, S-Video) is

input to the sub screen, horizontal lines may icker. If this

happens, display the image on the main screen.

Enlarge

• Youcanalignseveralmonitorsandintegratethemintoa

single large screen to display.

• Uptovemonitorscanbealignedinboththehorizontal

and vertical directions.

• Eachmonitordisplaysenlargedviewsofseparatedimages.

(Example)

Horizontal direction: 2 monitors

Vertical direction: 2 monitors

Horizontal direction: 3 monitors

Vertical direction: 2 monitors

Setting procedure

Set using the MULTI menu.

1. Set ENLARGE to ON.

2. Select ADVANCED (ENLARGE).

3. Set the number of monitors aligned in the horizontal

direction in ENLARGE H.

4. Set the number of monitors aligned in the vertical

direction in ENLARGE V.

5. Set the section of the separated image to be displayed

on each monitor in ENLARGE-POS.

1) Press

2) Press

, , or to select position, then

press

TIPS

• WhenEnlargeisused,theSCREENMOTIONfunctionis

disabled.

• WhenEnlargeisused,theAUTOINPUTCHANGEfunction

is disabled.

• WhenEnlargeisused,theHDMIAUTOVIEWfunctionis

disabled.

Menu Items

ZOOM2 SPECIAL SETTING

If you connect a laptop computer with any of the following

screen resolutions and black bands appear around the

screen,setZOOM2SPECIALSETTINGofINPUTSIGNALon

theOPTIONmenutoONandthenselectZOOM2intheSIZE

setting.

This displays the area inside the black band.

Laptop computer

resolution

Correspondingsignal*

1280x800 1280x1024,1280x960,1400x1050*

1280x600 1280x720

1024x600 1024x768

*1:Thissettingiseffectiveonlywhenthescreenresolution,

including the black band, is one of the resolutions listed

above.

*2:Usetheautomaticscreenadjustment.

SCHEDULE

You can set the time to switch the monitor on and off.

Setthisfunctionwith“SCHEDULE”intheOPTIONmenu.(See

page 23.)

– – – – – – – – – – – –– – – – –

SCHEDULE

No.

POWERDAY OF THE WEEK

TIMEINPUT BRIGHT

– –

– – – – – – –

– –

– – – –

PC D-SUB

(1)

–

– – – – – – – – – – – –– – – – ––

(5)(2)(3) (4)(6)

OK···[MENU]

1920x1080

V: 60 Hz H: 67.5 kHz

1. Press or to select the SCHEDULE number, and

press

2. Set the SCHEDULE. (See the description below.)

Press

or to select items, and press or to

change the setting.

3. Press

SCHEDULEbecomeseffective.

(1)

●:SCHEDULEeffective

:SCHEDULEnoteffective

(2) POWER

ON : Switchesthemonitoronatthespeciedtime.

OFF: Switchesthemonitoroffatthespeciedtimeandputs

the monitor in standby mode.

(3) DAY OF THE WEEK

SpeciesthedayoftheweektoexecutetheSCHEDULE.

0:ONLYONCE

ExecutestheSCHEDULEonceonthespeciedday.

SpecifythedayoftheweektoexecutetheSCHEDULE.

1:EVERYWEEK

ExecutestheSCHEDULEonthespecieddayoftheweek

every week. Specify the day of the week to execute the

SCHEDULE.

Periodicsettingsuchas“MondaythroughFriday”isalso

possible.

2:EVERYDAY

ExecutestheSCHEDULEeverydayregardlessoftheday

of the week.

(4) TIME

SpeciesthetimetoexecutetheSCHEDULE.

Setthetimeona12-hourbasis.(Factorydefault)

Canbeenteredas24-hourtimeusingtheTIMEsettingin

DATE/TIMEFORMAT.

(5) INPUT

Speciestheinputmodeatpower-on.Whennotspecifying,

thescreenatthepreviouspower-offappears.

InputmodesdisplayedonDVI,HDMI,BNCandD-SUB

dependonINPUTSELECTsettings.

(6) BRIGHT

Sets the brightness when changing the screen brightness at

aspeciedtime.

Caution

• Donotswitchoffthemainpoweraftersettingthe

SCHEDULE.

• Specifythecorrectdateandtime.(Seepage23.)

SCHEDULEdoesnotfunctionunlessthedateandtimeare

specied.

• Checkregularlythatthesetdateandtimearecorrect.

• WhenSTANDBYMODEisLOWPOWER,SCHEDULE

cannot be set.

• Whenatemperatureabnormalityoccursandthebacklight

brightness is reduced, the brightness is not changed even

ifaschedulesettoBRIGHTisexecuted.

TIPS

• Upto8SCHEDULEitemscanberegistered.

• SettingtheSCHEDULEashesthepowerLEDalternately

in red and orange in standby mode.

• ASCHEDULEthathasalargenumberhasprecedence

over that of a small number when schedules overlap.

• IfD-SUBofINPUTSELECTontheOPTIONmenuissetto

AVVIDEO,theinputmodewillswitchtoAVVIDEO(D-SUB)

regardlessifsettoD-SUBorVIDEO.

Menu Items

ADVANCED items (AV input) (See page 21

for additional Menu item details.)

FLESH TONE

Adjustthehuecontrol.

3D-NR

Reduce the noise of playback images on video.

Settingahigherlevelreducesmorenoise.However,itmay

cause blurring on an image.

MPEG-NR

Reduce block noise caused by digital compression.

3D-Y/C (AV VIDEO)

Specifywhethertoperform3-dimensionY/Cseparation.

Ifdotinterferenceorcross-colorisoccurringinfast-motion

scenes,selecting“OFF”mayimprovetheimagequality.

C.M.S.-HUE

Adjustscolortonewith6colorsofR(red),Y(yellow),G

(green),C(cyan),B(blue),andM(magenta).

C.M.S.-SATURATION

Adjustscolorvividnesswith6colorsofR(red),Y(yellow),G

(green),C(cyan),B(blue),andM(magenta).

C.M.S.-VALUE

Adjustscolorbrightnesswith6colorsofR(red),Y(yellow),

G(green),C(cyan),B(blue),andM(magenta).

TIPS

• WhenFLESHTONEissettoLOWorHIGH,C.M.S.-HUE/

-SATURATION/-VALUEcannotbeset.

Adjustments for PC screen display

Automatic adjustment

WhenyouusethePCD-subinputterminalorPCRGBinput

terminalstodisplayaPCscreenforthersttime,orwhen

youchangethesettingofthePC,usetheautomaticscreen

adjustment.

1. Switch the input to PC D-SUB or to PC RGB and display

the adjustment pattern. (See the description below.)

2. Press

and use or to display the SCREEN

menu.

3. Press and select “AUTO”.

4. Press

 Theautomaticadjustmentiscompleteinseveralseconds.

5. Press

twice to close the menu screen.

TIPS

• Ifthescreencannotbeadjustedproperlywithone

automaticadjustment,repeattheautomaticadjustmenttwo

orthreetimes.Trymanualadjustmentifnecessary.

Screen display for adjustment

BeforemakingadjustmentsintheSCREENmenuor

PICTUREmenu,displayanimagetobrightentheentire

screen.IfyouareusingaWindowsPC,usetheadjustment

patternonthesuppliedCD-ROM.

Opening the adjustment pattern

ThefollowingexampleisperformedinWindows7.

1. Load the supplied CD-ROM into the computer’s CD-

ROM drive.

2. Open [CD Drive] in [Computer].

InWindowsXP,open[CDDrive]in[MyComputer].

3. Double-click [Adj_uty.exe].

 Theadjustmentpatternwillappear.

 Adjustthescreenautomaticallyormanually.

4. When adjustment is nished, press the [Esc] on the

computer’s keyboard to quit the adjustment program.

5. Eject the CD-ROM from the CD-ROM drive.

TIPS

• Ifthedisplaymodeonthecomputeryouareusingis

65,000colors,thecolorlevelsinthecolorpatternmay

appear differently or grayscale may appear to be colored.

(Thisisduetothespecicationsoftheinputsignalandis

not a malfunction.)

Menu Items

You can return the settings to their factory-preset values and

restrict operations.

1. Hold

SIZE

down until “F” appears in the upper left

corner of the screen.

2. While “F” appears, press

, , , in that

order.

▲

▲▲▲▲▲▲▲

▲ ▲ ▲ ▲ ▲ ▲ ▲

OFF

UNLOCKED

ON1

LED

OFF

MONITOR

FUNCTION

1/1

ALL RESET

ADJUSTMENT LOCK

ADJUSTMENT LOCK TARGET

RS-232C

OSD DISPLAY

LED

TEMPERATURE ALERT

STATUS ALERT

POWER BUTTON

CONTROLLER INPUT

END…[MENU]

3. Select and set the items.

ALL RESET

Resets the settings to the factory default settings.

Press

, select ALL RESET, and then press

After initialization, turn the main power switch off and

then back on.

When the PN-ZB01 (optional) is attached, press ,

select the resetting method, and then press

ALL RESET1 ....Resets all the settings to the factory

default settings.

ALL RESET2 ....Returns all settings to the factory default

settings except for the following items:

LAN SETUP, RS-232C/LAN SELECT,

ID No. SET, BAUD RATE, NETWORK,

MAIL, SERVICE & SUPPORT, and

SNMP (See page 23, and pages 46 to

49.)

ADJUSTMENT LOCK

You can disable operations on the monitor and the

remote control unit that use buttons.

OFF ...Enables operation.

ON 1 ..Disables all operations other than turning power

on/off and FUNCTION.

ON 2 ..Only the FUNCTION operation is enabled.

Disables all operations other than FUNCTION (not

even power on/off).

ADJUSTMENT LOCK TARGET

Sets the target to prohibit operation of with

ADJUSTMENT LOCK.

REMOTE CONTROL ..... Prohibits remote control

operation

MONITOR BUTTONS ... Prohibits monitor switch

operation

BOTH ............................. Prohibits remote control and

monitor switch operation

RS-232C

(RS-232C/LAN when the PN-ZB01 (optional) is

attached)

Species whether to allow control via RS-232C or LAN

(see pages 30 and 42).

Initialization (Reset)/Functional Restriction Setting (FUNCTION)

OSD DISPLAY

Shows/hides the menu, modes, and messages.

The FUNCTION screen cannot be hidden.

ON 1 .............. Shows all menus, modes and messages.

ON 2 .............. Hides messages automatically displayed

by the display. Shows messages during

operation.

OFF ............... Hides all menus, modes and messages.

LED

Species whether to light the power LED.

OFF cannot be selected when STANDBY MODE is LOW

POWER.

TEMPERATURE ALERT

Selects the notication method for an abnormal

temperature.

OFF .............. Do not notify about an abnormal

temperature.

OSD & LED .. When an abnormal temperature is

detected, the power LED ashes in red

and green alternately and the screen

displays a message: TEMPERATURE.

LED............... When an abnormal temperature is

detected, the power LED ashes in red

and green alternately.

STATUS ALERT

Selects the notication method for a hardware error.

OFF .............. Do not notify about the error.

OSD & LED .. When a hardware error is detected, the

power LED ashes in red and the screen

displays a message: STATUS [xxxx].

LED............... When a hardware error is detected, the

power LED ashes in red.

POWER BUTTON

Normally, leave this setting as MONITOR.

When using an optional part, if instruction appears,

change the setting accordingly.

CONTROLLER INPUT

Normally, you do not need to change this setting.

When using an optional part, if instruction appears,

change the setting accordingly.

4. Press

to return to the normal screen.

TIPS

• When both abnormal temperature and hardware error are

detected, the hardware error notication overrides.

• If TEMPERATURE ALERT or STATUS ALERT is set to

OSD&LED, alert messages will appear even if the OSD

DISPLAY is set to ON 2 or OFF.

Controlling the Monitor with a PC (RS-232C)

YoucancontrolthismonitorfromaPCviaRS-232C(COM

port)onthePC.

You can also connect multiple monitors via a daisy chain by

usingaPC.ByassigningIDnumberstoeachmonitor(see

page31),youcanmakeinputmodeselection/adjustmentor

cancheckthestatusofaspecicmonitor.

Precautions when the PN-ZB01 (optional) is attached

• TocontrolthemonitorviaRS-232C,setRS-232C/LAN

SELECTtoRS-232C.

• YoucannotuseRS-232CandLANcontrolsimultaneously.

PC connection

One-to-one connection with a PC

ConnectwithRS-232straightcablebetweenthePC’sCOM

port(RS-232Cconnector)andtheRS-232Cinputterminalon

the monitor.

RS-232 straight cable

(commercially available)

To COM port

RS-232C input terminal

Daisy chain connection…

Advanced operation

ConnectwithRS-232straightcablebetweenthePC’sCOM

port(RS-232Cconnector)andtheRS-232Cinputterminalon

therstmonitor.

Next,connectRS-232straightcabletotherstmonitor’s

RS-232Coutputterminalandtothesecondmonitor’s

RS-232Cinputterminal.Connectinthesamewaytothethird

andsubsequentmonitors.

Upto25monitorscanbeconnected.(Dependingonthe

length of the cable used and the surrounding environment.)

To COM port

RS-232 straight cables

(commercially available)

First monitor

Second monitor

RS-232C

input terminal

RS-232C

output terminal

Communication conditions

SettheRS-232CcommunicationsettingsonthePCtomatch

the monitor’s communication settings as follows:

Baudrate *

Stop bit

1bit

Datalength 8 bits Flowcontrol None

Parity bit None

*SettothesamebaudrateastheBAUDRATEsettingof

SETUPmenu.(Initialsetting:38400bps)

*Whenconnectingmultiplemonitorsinadaisychain,setall

monitorstothesameBAUDRATE.

Communication procedure

Command format

WhenacommandissentfromthePCtothemonitor,the

monitor operates according to the received command and

sendsaresponsemessagetothePC.

C1 C2 C3 C4 P1 P2 P3 P4

Return code

Command field

(4 prescribed

alphanumerical characters

)

Parameter field

(4 character string comprised of:

0-9, +, -, space, ?)

Example:VOLM0030

 VOLM

30

* Besuretoinput4charactersfortheparameter.Padwith

spaces (“

”) if necessary.

(“

”isareturncode(0D

,0A

or0D

))

Wrong :VOLM30

Right :VOLM 30

Wheninputtinganegativevalue,specifyanumericalvaluein

three digits.

Example:AUTR-005

DonotusespacesforMPOS,DATE,andSC01through

SC08.Specifyparametersusingaspeciednumberof

characters.

Example:MPOS010097

Ifacommandhas“R”listedfor“DIRECTION”inthe

“RS-232Ccommandtable”onpage34,thecurrentvaluecan

be returned by using “?” as the parameter.

Example:

VOLM???? ←

FromPCtomonitor(Howmuch

is current volume setting?).

30 ←

FrommonitortoPC(Current

volumesetting:30).

* IfanIDnumber(seepage31)hasbeenassigned

(Forexample,IDnumber=1).

VOLM

? ←

FromPCtomonitor.

30 001 ←

FrommonitortoPC.

Controlling the Monitor with a PC (RS-232C)

Response code format

When a command has been executed correctly

O K

Return code

(0DH, 0AH)

A response is returned after a command is executed.

* IfanIDnumberhasbeenassigned

O K SPC 0 0 1

ID number of respondin

monitor

Space (20

Return code

(0DH, 0AH)

When a command has not been executed

R R E

Return code

(0DH, 0AH)

* IfanIDnumberhasbeenassigned

R R E SPC 0 0 1

ID n

Space (20H)

Return code

(0DH, 0AH)

TIPS

• “ERR”isreturnedwhenthereisnorelevantcommandor

when the command cannot be used in the current state of

the monitor.

• Ifcommunicationhasnotbeenestablishedforreasons

suchasabadconnectionbetweenthePCandmonitor,

nothingisreturned(notevenERR).

• “ERR”maybereturnedwhenacommandcannotbe

received correctly due to interference from the surrounding

environment.

Please ensure that the system or software retries the

command if this occurs.

• IfnomonitorhasbeenassignedthedesignatedIDnumber

(e.g.ifthecommandIDSL0002

is used, but no monitor

withIDnumber:2isfound),noresponseisreturned.

If execution of the command is taking some time

I W T A

Return code

(0DH, 0AH)

Whenthefollowingcommandsareused,“WAIT”isreturned.

Inthiscase,avaluewillbereturnedifyouwaitawhile.Donot

send any command during this period.

NoIDnumberisattachedtoWAITresponse.

• CommandswhichreturnWAIT:

1. Whenrepeatercontrolisused

2. WhenanIDSLorIDLKcommandisused

3. Whenoneofthefollowingcommandsisused:RSET,

INPS,ASNC,WIDE,EMAG,EPOS,PXSL,POWR,

AGIN,MWIN,MWIP,MWPP,ESTG,EMHV,EPHV,

ESHV,ENLG

When control via RS-232C is locked (to prevent use)

using the operation lock function (see page 29)

E C D K O L

Return code

(0D

H, 0AH)

When RS-232C/LAN SELECT is set to LAN

U N S E L E C T E D

Return code

(0D

H, 0AH)

Communication interval

• AfterOKorERRisreturned,youmustsendthefollowing

commands.

 Tosetatimeoutforthecommandresponse,specify10

seconds or longer.

Whenconnectingmultiplemonitorsinadaisychain,setthe

timeout to at least the product of the monitor’s position from

thecomputermultipliedby10seconds.

Example)3rdmonitorfromcomputer:30secondsorlonger.

• Provideanintervalof100msormorebetweenthe

command response and the transmission of the next

command.

VOLM0020

INPS0001

WAIT

Interval of 100 ms or more

TIPS

• WhenexecutingALLRESET,setthetimeoutperiodto30

seconds or longer.

• WhenturningthepoweronwhilethePOWERONDELAY

functionisinuse,setthetimeoutperiodtothePOWERON

DELAYperiod+10secondsorlonger.

Advanced operation

This section explains commands for daisy chain connection.

The basic communication procedure is the same as in the

“One-to-oneconnectionwithaPC”section.

ID numbers

YoucanassignauniqueIDnumbertoeachmonitor(see

page 23). This allows you to control a particular monitor in a

daisy chain of monitors.

YoucanassignIDnumberseitherfromthemenuscreenor

fromthePCusingRS-232cable.

xamp

]

ID number: 1 ID number: 2 ID number: 3 ID number: 4

If monitors are connected as shown above, you can

execute commands like “Set the volume of the monitor with

ID4to20”.

WhendesignatingIDnumbersforasetofmonitorslinkedina

daisychain,youshouldbasicallyavoidanyduplicationofID

numbers.

IDnumbersdonothavetobeassignedinascendingorder

startingfromthePC.Theycanalsobeconnectedasshown

below.

xamp

]

ID number: 3 ID number: 2 ID number: 4 ID number: 1

Controlling the Monitor with a PC (RS-232C)

Commands for ID control

The command examples shown on this page assume the

followingconnectionandIDnumbersetup.

ID number: 1 ID number: 2 ID number: 3 ID number: 4

IDST .........AmonitorreceivingthiscommandsetsitsownID

numberintheparametereld.

Example:

IDST0001

OK

001 ←

TheIDnumberofthismonitorissetto1.

TIPS

YoucanautomaticallyassignIDnumbersbyusingtheIDST

command with the Repeater control (see “Repeater control”

on page 33).

Forexample,usingthecommand“IDST001+”automatically

setstheIDnumbers,asshownbelow.

xamp

]

ID number: 1 ID number: 2 ID number: 3 ID number: 4

IDST001+ ←

IDsettingcommandwithrepeatercontrol

WAIT

OK

001 ←

“OK”responsefromIDnumber:1

OK 002 ←

“OK”responsefromIDnumber:2

OK 003 ←

“OK”responsefromIDnumber:3

OK 004 ←

“OK”responsefromIDnumber:4(End)

IDSL ........TheparameterofthiscommandsetstheIDnumber

ofthemonitor.Themonitorissubjecttothenext

command.

Example:

IDSL0002 ←

The next command is for the monitor

withIDnumber:2.

WAIT ←

SearchingformonitorwithIDnumber:

OK 002 ←

FoundmonitorwithIDnumber:2

VOLM0030 ←

SetsvolumeofmonitorwithID

number:2to30.

WAIT ←

Processing

OK 002 ←

OKresponsefrommonitorwithID

number: 2

VOLM0020 ←

Setsvolumeto20.

OK 001 ←

ThevolumeofthemonitorwithID

number:1(theonedirectlyconnected

tothePC)issetto20.*

* TheIDSLcommandiseffectiveonlyonce,forthe

immediately succeeding command.

IDLK ........

TheparameterofthiscommandsetstheID

numberofthemonitor.Themonitorissubjecttoall

subsequentcommands.

Example:

IDLK0002 ←

Followingcommandsareforthemonitor

withIDnumber:2.

WAIT ←

SearchingformonitorwithIDnumber:

OK 002 ←

FoundmonitorwithIDnumber:2

VOLM0030 ←

SetsvolumeofmonitorwithID

number:2to30.*

WAIT ←

Processing

OK 002

VOLM0020 ←

SetsvolumeofmonitorwithID

number:2to20.*

WAIT

OK

002

IDLK0000 ←

CancelingxedIDnumbersetting

WAIT ←

CancelingIDLK

OK 002 ←

Cancelationcomplete

VOLM0010

OK

001 ←

ThevolumeofthemonitorwithIDnumber:

1(theonedirectlyconnectedtothePC)is

setto10.(IDLKiscanceled.)

* TheIDLKcommandremainseffectiveuntilitis

canceled, or power is shut off.

IDCK ........ProvidesscreendisplayoftheIDnumbercurrently

assignedtoamonitor,andtheIDnumbercurrently

setforIDLK(ifany).

Example:

(AfterexecutingIDLK0002)

IDCK0000

←

(Parameter has no meaning.)

ID:001IDLK:002

←

Returnedresponse.TheID

number is also displayed on the

monitor screen.

IDCK000+

←

Repeater control. (If a command

isusedwithrepeatercontrol,ID

designationusingIDSLorIDLK

is canceled.)

WAIT

ID:001IDLK:000

ID:002IDLK:000

ID:003IDLK:000

ID:004IDLK:000

Controlling the Monitor with a PC (RS-232C)

Repeater control

This system has a function to allow setting of multiple

monitors connected in a daisy chain using a single command.

This function is called repeater control. You can use Repeater

controlfunctionwithoutassigningIDnumbers.

xamp

]

Set 1

Set 2 Set 3Set 4

* Ifmonitorsareconnectedasshownabove,youcan

execute a command like “Set all monitors’ input settings to

PCD-SUB”.

Repeater control command

RepeatercontrolisachievedbysettingtheFOURTH

CHARACTERoftheparameterto“+”.

Example:

VOLM030+ ←

Setsvolumeofallmonitorsto30.

In repeater control, responses are returned by all the

connected monitors.

If you want to determine that a value has been returned by a

specicset,assignIDnumberstoeachmonitorinadvance.

Whensomemonitorsdonotreturntheirresponses,the

probable cause is that the monitors could not receive the

commandorcommandprocessingisnotcomplete.Donot

send a new command.

Example: (When4monitorsareconnected,and

assignedIDnumbers:1through4)

VOLM030+

WAIT

OK

001

OK

002

OK

003

OK

004 ← If 4 monitors are connected in

a chain, reliable operation can

be ensured by sending a new

command only after a reply

has been returned by 4th (last)

monitor.

Repeater control can also be used for reading settings.

Example:

VOLM???+

WAIT

10

001

Volumesettingsforall

monitors are returned.

20

002

30

003

30

004

TIPS

• IfrepeatercontrolisusedduringIDdesignation(IDSL,

IDLK),theIDdesignationiscanceled.

Setting of the GAMMA user data

To transfer the GAMMA user data

Usetheuserdatatransfercommands(UGRW,UGGWand

UGBW).ForeachoftheR,GandBcolors,dividethetotal

512piecesofuserdatainto16blocks,andtransfer32pieces

of data with each command.

C1 C2 C3 C4 P1 P2 P3 P4

…

S1 S2

Command field

Block number (01 to 16)

Data fieldChecksum field

Example:Totransferthedataofblock1(0to31levels)

of red (R) data

UGRW01000000010002 … 0031C0

Command

Block number

32 pieces of data Checksum

One piece of data consists

of 4 digits.

* Ifdataislessthan4digits,adda“0”(zero)tomakeit4

digits.

* Thechecksumeldisthecharacterstring(ASCII)dataof

lower-orderonebytewhichindicatesthesumoftheblock

numberand32piecesofdatainhexadecimal(0toF).

Saving the GAMMA user data

Usetheuserdatasavecommand(UGSV)tosavethe

transferred user data in the monitor.

If the data is not saved, it will be cleared when:

• Themainpowerswitchisoff

• STANDBYMODEisLOWPOWERandthemonitorenters

standby mode

Activating the GAMMA user data

Toactivatethetransferreduserdata,selectUSERforGAMMA

ofthePICTUREmenu,orsendthecorrespondingRS-232C

command.

Checking the GAMMA user data

Usetheuserdatareadcommands(UGRR,UGGRand

UGBR)toreturn512piecesofuserdataforeachoftheR,

GandBcolors.Dividethedatainto16blocksandreturn32

pieces of data with each command. The value to be returned

is not the value stored in the monitor, but the value in the

temporary memory for display. (These values are the same

whentheuserdatasavecommand(UGSV)abovehasbeen

sent.)

TIPS

• TheuserdataisnotinitializedbyRESETofthePICTURE

menu.Toinitializetheuserdata,useALLRESETofthe

FUNCTIONmenu.

TheGAMMAuserdatainitializecommand(UGRS)allows

theinitializationoftheuserdataonly.

RS-232C command table

How to read the command table

Command: Commandeld(Seepage30.)

Direction: W Whenthe“Parameter”issetintheparametereld(seepage30),thecommandfunctionsasdescribed

under“Control/ResponseContents”.

R The returned value indicated under “Reply” can be obtained by setting “????”, “

?”or“???+”

(repeatercontrol)intheparametereld(seepage30).

Parameter: Parametereld(Seepage30.)

Reply: Response (Returned value)

*1:

“●”indicatesacommandwhichcanbeusedinpowerstandbymoderegardlessoftheSTANDBYMODEsetting.

“○”indicatesacommandwhichcannotbeusedinpowerstandbymodewhenSTANDBYMODEissettoLOWPOWER.

“–”indicatesacommandwhichcannotbeusedinpowerstandbymoderegardlessoftheSTANDBYMODEsetting.

*2: PN-ZB01(optional)limitations

 (A)WhenPN-ZB01(optional)isnotattached,(B)WhenPN-ZB01(optional)isattached.

 ○:Thecommandcanbeused.

 - :Error(ERR)

Power control/Input mode selection

Function

Command Direction

Parameter Reply Control/Response contents *1

(A) (B)

POWERCONTROL POWR W 0

Switches to standby mode.

● ○ ○

1 Returns from standby mode.

R 0 Standby mode

1 Normal mode

2 Input signal waiting mode

INPUTMODESELECTION INPS W 0 Togglechangeforinputmode.TerminalsnotselectedinINPUTSELECT

cannot be selected.

●

○ ○

1 PCDVI-D

“ERR”whenAVDVI-DisselectedforDVIofINPUTSELECT.

○

2 PCD-SUB

“ERR”whenotherthanPCD-SUBisselectedforD-SUBofINPUTSELECT.

○ ○

3 AVCOMPONENT(BNC)/AVCOMPONENT(D-SUB)

“ERR”whenotherthanPCRGBisselectedforBNCofINPUTSELECT,and

whenotherthanAVCOMPONENTisselectedforD-SUBofINPUTSELECT.

○ ○

4 AVVIDEO(BNC)/AVVIDEO(D-SUB)

○ ○

6 PCRGB

“ERR”whenAVCOMPONENTisselectedforBNCofINPUTSELECT.

○

7 AVDVI-D

“ERR”whenPCDVI-DisselectedforDVIofINPUTSELECT.

○

8 AVS-VIDEO -

○

9 AVHDMI

“ERR”whenPCHDMIisselectedforHDMIofINPUTSELECT.

○ ○

10 PCHDMI

“ERR”whenAVHDMIisselectedforHDMIofINPUTSELECT.

○ ○

R 1 PCDVI-D

● ○ ○

2 PCD-SUB

3 AVCOMPONENT

4 AVVIDEO

6 PCRGB

7 AVDVI-D

8 AVS-VIDEO

9 AVHDMI

10 PCHDMI

Controlling the Monitor with a PC (RS-232C)

SCREEN menu

Function

Command Direction

Parameter Reply Control/Response contents *1

(A) (B)

AUTO ASNC W 1 When the input mode is PC D-SUB, PC RGB.

○ ○

CLOCK CLCK WR 0-1200 0-1200 When the input mode is PC D-SUB, PC RGB.

Varies depending on the signal.

PHASE PHSE WR 0-63 0-63 When the input mode is PC D-SUB, PC RGB.

POSITIONING POSITION OF

THE LONGEST

DIRECTION

HPOS WR 0-100 0-100 0-800 on PC D-SUB, PC RGB.

Varies depending on the signal.

POSITION OF

THE SHORTEST

DIRECTION

VPOS WR 0-100 0-100 0-200 on PC D-SUB, PC RGB.

Varies depending on the signal.

SIZE SIZE OF THE

LONGEST

DIRECTION

HSIZ WR 0-100 0-100

SIZE OF THE

SHORTEST

DIRECTION

VSIZ WR 0-100 0-100

RESOLUTION

LONGEST

DIRECTION

RESOLUTION

HRES WR 300-1920 300-1920 When the input mode is PC D-SUB, PC RGB.

Only even numbers are valid for parameters.

Varies depending on the signal.

SHORTEST

DIRECTION

RESOLUTION

VRES WR 200-1200 200-1200

RESET ARST W 1

Controlling the Monitor with a PC (RS-232C)

PICTURE menu

Function

Command Direction

Parameter Reply Control/Response contents *1

(A) (B)

AUTO AGIN W 1 When the input mode is PC D-SUB, PC RGB. -

○

ANALOG GAIN ANGA WR 0-127 0-127 When the input mode is PC D-SUB, PC RGB.

○

ANALOG OFFSET ANOF WR 0-127 0-127 When the input mode is PC D-SUB, PC RGB.

CONTRAST CONT WR 0-60 0-60

BLACK LEVEL BLVL WR 0-60 0-60

TINT TINT WR 0-60 0-60

COLORS COLR WR 0-60 0-60

SHARPNESS SHRP WR 0-24 0-24

RGB INPUT RANGE (AV HDMI) AHDR WR 0-2 0-2 0: AUTO, 1: FULL, 2: LIMITED

RGB INPUT RANGE (PC HDMI) PHDR WR 0-2 0-2 0: AUTO, 1: FULL, 2: LIMITED

RGB INPUT RANGE (AV DVI) ADVR WR 1-2 1-2 1: FULL, 2: LIMITED

RGB INPUT RANGE (PC DVI) PDVR WR 1-2 1-2 1: FULL, 2: LIMITED

RGB INPUT RANGE (D-SUB) PDSR WR 1-2 1-2 1: FULL, 2: LIMITED

RGB INPUT RANGE (PC BNC) PBRR WR 1-2 1-2 1: FULL, 2: LIMITED

ADVANCED

(When the input

mode is AV.)

FLESH TONE FLES WR 0-2 0-2 0: OFF, 1: LOW, 2: HIGH

○

3D-NR TDNR WR 0-2 0-2 0: OFF, 1: LOW, 2: HIGH

MPEG-NR MPNR WR 0-1 0-1 0: OFF, 1: ON

3D-Y/C YCSP WR 0-1 0-1 0: OFF, 1: ON (When the input mode is AV VIDEO)

C.M.S.-HUE CMHR WR -10-10 -10-10 R

CMHY Y

CMHG G

CMHC C

CMHB B

CMHM M

CRST W 1 Resets the hue.

C.M.S.-

SATURATION

CMSR WR -10-10 -10-10 R

CMSY Y

CMSG G

CMSC C

CMSB B

CMSM M

CRST W 2 Resets the saturation.

C.M.S.-VALUE CMVR WR -10-10 -10-10 R

CMVY Y

CMVG G

CMVC C

CMVB B

CMVM M

CRST W 3 Resets the brightness.

COLOR MODE BMOD WR 0 0 STD

○

2 2 VIVID

3 3 sRGB (When the input mode is PC)

4 4 HIGH ILLUMINANCE

WHITE BALANCE THRU CTMP WR 0 0 When the input mode is PC DVI-D/PC HDMI.

○

PRESET 1-18 1-18 From 1: approximately 3,000K to 15: approximately 10,000K

(500K steps)

16: approximately 5,600K, 17: approximately 9,300K,

18: approximately 3,200K

USER 99 99

R-CONTRAST CRTR WR 0-256 0-256 “ERR” when CTMP is not set to 99.

G-CONTRAST CRTG WR 0-256 0-256

B-CONTRAST CRTB WR 0-256 0-256

R-OFFSET OFSR WR -127-127 -127-127

G-OFFSET OFSG WR -127-127 -127-127

B-OFFSET OFSB WR -127-127 -127-127

COPY TO USER CPTU W 0 Copies a preset value to the user setting. -

GAMMA GAMM WR 0-2 0-2 0: 1.8, 1: 2.2, 2: 2.4 (during PC input)

0: LIGHT 2, 2: DARK (during AV input)

○

4-6 4-6 4: USER, 5: 2.0, 6: STD (during PC input)

4: USER, 5: LIGHT 1, 6: STD (during AV input)

DISPLAY COLOR PATTERN PTDF WR 0 0 No pattern display.

1 1 White single color pattern display.

2 2 Red single color pattern display.

3 3 Green single color pattern display.

4 4 Blue single color pattern display.

99 99 Red/green/blue mixed color pattern display.

Set each color's level with RED, GREEN, BLUE.

RED PTDR WR 0-15 0-15 “ERR” when PTDF is not set to 99.

GREEN PTDG WR 0-15 0-15

BLUE PTDB WR 0-15 0-15

RESET ARST W 2

Controlling the Monitor with a PC (RS-232C)

AUDIO menu

Function

Command Direction

Parameter Reply Control/Response contents *1

(A) (B)

TREBLE AUTR WR -5-5 -5-5

○

○ ○

BASS AUBS WR -5-5 -5-5

BALANCE AUBL WR -10-10 -10-10

RESET ARST W 3

SETUP menu

Function

Command Direction

Parameter Reply Control/Response contents *1

(A) (B)

OSD H-POSITION OSDH WR 0-100 0-100

○

○ ○

OSD V-POSITION OSDV WR 0-100 0-100

SCREEN MOTION SCSV WR 0-4 0-4 0: OFF, 1-4: PATTERN1-4

○

MOTION TIME 1 MTIM WR 0-20 0-20

○

MOTION TIME 2 PATTERN1 MINT WR 10-990 10-990 Per 10 seconds

○

PATTERN2-4 MINT WR 5-20 5-20 Per second

MONITOR STDR WR 0-1 0-1 0: LANDSCAPE, 1: PORTRAIT

○

MONAURAL AUDIO MONO WR 0-1 0-1 0: OFF, 1: ON

○

LANGUAGE LANG WR 14 14 ENGLISH

○

1 1 DEUTSCH

2 2 FRANÇAIS

3 3 ITALIANO

4 4 ESPAÑOL

5 5 РУССКИЙ

6 6

POWER ON DELAY PWOD WR 0 0 OFF

○

1-60 1-60 ON

STANDBY MODE STBM WR 0-1 0-1 0: STANDARD, 1: LOW POWER

(“ERR" when SCHEDULE is effective or OFF is selected for LED.)

○

OFF IF NO OPERATION ATOF WR 0-1 0-1 0: OFF, 1: ON

○

HOT PLUG CONTROL (DVI) HPCT WR 0-1 0-1 0: OFF, 1: ON

○

HOT PLUG CONTROL (HDMI) HPCH WR 0-1 0-1 0: OFF, 1: ON

○ ○ ○

RS-232C/LAN SELECT CTLS WR 0-1 0-1 0 : RS-232C 1 : LAN

○

ID NUMBER ID NO. SETTING IDST W 0-255 Sets the monitor’s ID number. (“0” means “no ID number”.)

○ ○ ○

R 0-255 Returns the monitor’s ID number.

ID NO. SETTING

(ONCE)

IDSL W 1-255 Sets a monitor ID number.

This ID number is only effective for the command immediately after this

command.

0 Clears the ID number if one has been designated.

ID NO. SETTING

(SUBSEQUENT)

IDLK W 1-255 Sets a monitor ID number.

This ID number is effective for the next and all subsequent commands

after this command.

0 Clears the ID number if one has been designated.

ID CHECK IDCK W 0 ID : xxx

IDLK : yyy

Displays monitor’s own ID number and the selected ID number on the

screen.

ID DISPLAY IDDP W 0-2 0: OFF, 1: ON, 2: ON (turns OFF after 4 sec.)

(When the PN-ZB01 is attached, the IP address and MAC address are

both displayed.)

BAUD RATE BAUD WR 0-2 0-2 0: 9600bps, 1: 19200bps, 2: 38400bps

○ ○ ○

SPEAKER SELECT SPSL WR 0-1 0-1 0: Internal speaker, 1: External speaker

○

HDMI AUTO VIEW HDAW WR 0-1 0-1 0: OFF, 1: ON

○ ○ ○

SETTING COPY MODE CPMD WR 0 0 Copy to all monitors.

○ ○ ○

1-225 1-225 Copy to the monitor with the set ID Number.

SETTING COPY TARGET CPTG WR 0 0 Copies the PICTURE menu settings.

1 1 Copies all the settings.

LOGO SCREEN BTSC WR 0-1 0-1 0: OFF, 1: ON

Controlling the Monitor with a PC (RS-232C)

OPTION menu

Function

Command Direction

Parameter Reply Control/Response contents *1

(A) (B)

DATE/TIME SETTING DATE WR

AABBCCDDEE AABBCCDDEE

AA: Year, BB: Month, CC: Day, DD: Hour, EE: Minute

○ ○ ○

DATE DISPLAY FORMAT DTFT WR

0-2 0-2

0: YYYY/MM/DD, 1: MM/DD/YYYY, 2: DD/MM/YYYY

YYYY: Year, MM: Month, DD: Day

TIME DISPLAY FORMAT TMFT WR

0-1 0-1

0: 24-HOUR TIME, 1: 12-HOUR TIME

SCHEDULE SC01-

SC08

WR ABCDEFFGGH ABCDEFFGGH Schedule of a specied number

A: Schedule 0= Not effective, 1 = Effective

B: Power 0 = OFF, 1 = ON

C: Day of the week 1 0 = Only once, 1 = Every week, 2 = Every day

D: Day of the week 2 0 = Sunday, 1 = Monday through 6 = Saturday,

9 = Not exist

E: Day of the week 3 0 = Sunday, 1 = Monday through 6 = Saturday,

9 = Not exist

F: Hour 00-23

G: Minute 00-59

H: Input 0 = Not specied, 1 = PC DVI-D/AV DVI-D,

2 = PC D-SUB, 3 = PC RGB/AV COMPONENT,

4 = AV VIDEO, 5 = AV S-VIDEO,

6 = PC HDMI/AV HDMI

“ERR” when LOW POWER is selected for STANDBY MODE.

SCHEDULE BRIGHTNESS SB01-

SB08

WR 0-31 0-31 Screen brightness to change

99 99 Disable brightness setting

INPUT SELECT DVI DVSL WR 0-1 0-1 0: PC DVI-D, 1: AV DVI-D

○

BNC BNSL WR 0-1 0-1 0: PC RGB, 1: AV COMPONENT

○

D-SUB SLDS WR 0-2 0-2 0: PC D-SUB, 1: AV COMPONENT, 2: AV VIDEO

○ ○

HDMI HDSL WR 0-1 0-1 0: PC HDMI, 1: AV HDMI

○ ○

AUDIO SELECT PC DVI-D ASDP WR 1-3 1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)

○

PC HDMI ASHP WR 0-1 0-1 0: HDMI, 1: AUDIO(STEREO MINI)

○

2-3 2-3 2: AUDIO1(RCA), 3: AUDIO2(RCA) -

PC D-SUB ASAP WR 1-3 1-3 1: AUDIO(STEREO MINI)

○

2: AUDIO1(RCA), 3: AUDIO2(RCA) -

PC RGB ASCP WR 1-3 1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA) -

AV DVI-D ASDA WR 1-3 1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA) -

AV HDMI ASHA WR 0-1 0-1 0: HDMI, 1: AUDIO(STEREO MINI)

○

2-3 2-3 2: AUDIO1(RCA), 3: AUDIO2(RCA) -

AV COMPONENT

(BNC)

ASCA WR 1-3 1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)

AV COMPONENT

(D-SUB)

ASC2 WR 1-3 1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)

○

AV S-VIDEO ASSA WR 1-3 1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA) -

AV VIDEO (BNC) ASVA WR 1-3 1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA) -

AV VIDEO (D-SUB)

ASV2 WR 1-3 1-3 1: AUDIO(STEREO MINI), 2: AUDIO1(RCA), 3: AUDIO2(RCA)

○

INPUT

RESOLUTION

(PC)

RESOLUTION CHECK

PXCK R - Returns current resolution in the form of hhh, vvv.

○ ○

PIXEL SETTING

(PC D-SUB, PC

RGB)

PXSL WR 1 1 768) 1360 x 768

2 2 768) 1280 x 768

3 3 768) 1024 x 768

5 5 480) 848 x 480

6 6 480) 640 x 480

7 7 1050) 1680 x 1050

8 8 1050) 1400 x 1050

9 9 768) AUTO

10 10 480) AUTO

INPUT RESOLUTION (AV)

RESOLUTION CHECK

RESO R - 480i, 480p, 1080i, 720p, 1080p, VGA , etc. -

ZOOM2 SPECIAL SETTING

(PC D-SUB, PC RGB)

Z2SP WR 0-1 0-1 0: OFF, 1: ON

○

SCAN MODE SCAN WR 0-2 0-2 0: MODE1, 1: MODE2, 2: MODE3 (When the input mode is AV)

○

POWER MANAGEMENT (PC) PMNG WR 0-1 0-1 0: OFF, 1: ON

○

POWER MANAGEMENT (AV) PMAV WR 0-1 0-1 0: OFF, 1: ON

○

COLOR SYSTEM CSYS WR 0-5 0-5 0: AUTO, 1: PAL, 2: PAL-60, 3: SECAM, 4: NTSC3.58, 5: NTSC4.43

○

AUDIO OUTPUT(RCA) AOUT WR 0-2 0-2 0: VARIABLE1, 1: FIXED, 2: VARIABLE2

○

AUDIO LEVEL(STEREO MINI) AIVP WR 0-1 0-1 0: 1.0Vrms, 1: 0.5Vrms

○

SELF ADJUST AADJ WR 0-1 0-1 0: OFF, 1: ON

○

AUTO INPUT CHANGE AINC WR 0-1 0-1 0: OFF, 1: ON

○

MULTI menu

Function

Command Direction

Parameter Reply Control/Response contents *1

(A) (B)

ENLARGE ENLG WR 0-1 0-1 0:OFF,1:ON

○ ○

ENLARGEMODE EMAG WR 0-4 0-4 0:OFF,1:2x2,2:3x3,3:4x4,4:5x5

EMHV WR 11-55 11-55 1x1(OFF)to5x5(“mxn”isexpressedas“mn”,wheremandnare

thenumbersofmonitorsspeciedforthelongestdirectionandthe

shortest direction respectively.)

IMAGEPOSITION(MxN) EPHV WR 11-55 11-55 SpeciesvaluesintheorderofIMAGEPOSITIONINLONGEST/

SHORTESTDIRECTION.

IMAGEPOSITION(2x2) EPOS WR 0-3 0-3 See the description below.

IMAGEPOSITION(3x3) EPOS WR 0-8 0-8

IMAGEPOSITION(4x4) EPOS WR 0-15 0-15

IMAGEPOSITION(5x5) EPOS WR 0-24 0-24

ENLARGED

SCREEN

POSITIONING

THELONGEST

DIRECTION

EPSH WR -999-999 -999-999 ThesettingrangedependsontheENLARGEMODEsettingandthe

IMAGEPOSITION.

THESHORTEST

DIRECTION

EPSV WR -999-999 -999-999

BEZELADJUST BZCO WR 0-1 0-1 0:OFF,1:ON

BEZELADJUST TOP BZCT WR 0-1 0-1 0:OFF,1:ON

BOTTOM BZCB WR 0-1 0-1 0:OFF,1:ON

RIGHT BZCR WR 0-1 0-1 0:OFF,1:ON

LEFT BZCL WR 0-1 0-1 0:OFF,1:ON

BEZELWIDTH TOP BZWT WR 0-100 0-100

BOTTOM BZWB WR 0-100 0-100

RIGHT BZWR WR 0-100 0-100

LEFT BZWL WR 0-100 0-100

ENLARGE/IMAGEPOSITIONSETTING ESTG WR XXYY XXYY XX:ENLARGEMODE(SameasEMAG),YY:IMAGEPOSITION(Same

asEPOS)

ESHV WR XXYY XXYY XX:ENLARGEMODE(SameasEMHV),YY:IMAGEPOSITION(Same

asEPHV)

• IMAGEPOSITION(EPOS)setting

In landscape orientation

012

345

678

13 14

2 x 2 3 x 3 4 x 4 5 x 5

In portrait orientation

2 x 2 3 x 3 4 x 4 5 x 5

3813

9141924

Controlling the Monitor with a PC (RS-232C)

PIP/PbyP menu

Function

Command Direction

Parameter Reply Control/Response contents *1

(A) (B)

PIPMODES MWIN WR 0-3 0-3 0:OFF,1:PIP,2:PbyP,3:PbyP2

○

○ ○

PIPSIZE MPSZ WR 1-64 1-64

○

PIP POS THELONGEST

DIRECTION

MHPS W 0-100

○

R 0-100

○

THESHORTEST

DIRECTION

MVPS W 0-100

○

R 0-100

○

PIPPOSLD+SDBATCH MPOS W 0-100,0-100 Specify the position in MPOSxxxyyy format.

(xxx: Longer side, yyy: Shorter side position)

○

R 0-100,0-100 Returns a response in (xxx,yyy) format.

(xxx: Longer side, yyy: Shorter side position)

○

PIPBLEND MWBL WR 0-15 0-15

○

PIPSOURCE MWIP WR 1 1 PCDVI-D

○

2 2 PCD-SUB

○ ○

3 3 AVCOMPONENT(BNC)/AVCOMPONENT(D-SUB)

○ ○

4 4 AVVIDEO(BNC)/AVVIDEO(D-SUB)

○ ○

6 6 PCRGB -

○

7 7 AVDVI-D -

○

8 8 AVS-VIDEO -

○

9 9 AVHDMI

○ ○

10 10 PCHDMI

○ ○

SOUNDCHANGE MWAD WR 1-2 1-2 1:MAIN,2:SUB

○

○ ○

MAIN POS (Main screen) MWPP WR 0-1 0-1 0:POS1,1:POS2

○

PbyP2 POS (Sub screen) MW2P WR 0-2 0-2 0:POS1,1:POS2,2:POS3

○

AUTOOFF MOFF WR 0-1 0-1 0:MANUAL,1:AUTO

○

Initialization/Functional Restriction Setting (FUNCTION) menu

Function

Command Direction

Parameter Reply Control/Response contents *1

(A) (B)

ALLRESET RSET W 0 0:ALLRESET -

○

0-1 0:ALLRESET1,1:ALLRESET2 - -

○

ADJUSTMENTLOCK ALCK WR 0-2 0-2 0:OFF,1:ON1,2:ON2

○

○ ○

ADJUSTMENTLOCKTARGET ALTG WR 0-2 0-2 0:REMOTECONTROL,1:MONITORBUTTONS,2:BOTH

○

OSDDISPLAY LOSD WR 0-2 0-2 0:ON1,1:OFF,2:ON2

○

LED OFLD WR 0-1 0-1 0:ON,1:OFF

“ERR”whenLOWPOWERisselectedforSTANDBYMODE.

○

TEMPERATUREALERT TALT WR 0-2 0-2 0:OFF,1:OSD&LED,2:LED

○

STATUSALERT SALT WR 0-2 0-2 0:OFF,1:OSD&LED,2:LED

○

POWERBUTTON PBTN WR 0-1 0-1 0:MONITOR,1:CONTROLLER

○

CONTROLLERINPUT PCIP WR 0-2 0-2 0:D-SUB,1:HDMI(“ERR”whenMONITORisselectedforPOWER

BUTTON.)

○ ○ ○

2:DVI-D(“ERR”whenMONITORisselectedforPOWERBUTTON.)

○

Controlling the Monitor with a PC (RS-232C)

Others

Function

Command Direction

Parameter Reply Control/Response contents *1

(A) (B)

SCREEN SIZE (PC) WIDE WR 1-5 1-5 1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2

○

○ ○

SCREEN SIZE (AV) WIDE WR 1-5 1-5 1: WIDE, 2: ZOOM1, 3: ZOOM2, 4: NORMAL, 5: Dot by Dot

○

VOLUME VOLM WR 0-31 0-31

○

MUTE MUTE WR 0-1 0-1 0: OFF, 1: ON -

INFORMATION MODEL INF1 R Value

●

SERIAL NO SRNO R Value

BRIGHT VLMP WR 0-31 0-31

○

TEMPERATURE SENSOR DSTA R 0 Internal temperature normal

●

1 Internal temperature abnormal (Standby mode)

2 Internal temperature abnormal (Temperature is normal now, but it was

abnormal during operation.)

3 Internal temperature abnormal (Brightness of the backlight decreases.)

4 Temperature sensor abnormal

TEMPERATURE ACqUISITION ERRT R Value Temperature at temperature sensors 1 through 3 are returned in the

following forms:

[Sensor 1], [Sensor 2], [Sensor 3]

Indicates a temperature sensor abnormality when “126” is returned.

○

CAUSE OF LAST STANDBY MODE STCA W 0 Initialization

●

R 0 No detectable error has occurred

1 Standby mode by POWER button

2 Main power off by the main power switch

3 Standby mode by RS-232C or LAN

4 Input signal waiting mode by No Signal

6 Standby mode by abnormal temperature

8 Standby mode by SCHEDULE setting

20 Standby mode by OFF IF NO OPERATION setting

Commands for setting of the GAMMA user data

Function

Command Direction

Parameter Reply Control/Response contents *1

(A) (B)

RED GAMMA DATA TRANSFER UGRW W aaxxxx

···

xxxxcc

(xxxx: 32 pieces)

aa: 01-16

xxxx: 0000-1023

cc: 00-FF

aa: Block number

xxxx: 32 pieces of user data

cc: Checksum (ASCII data) of the block number and user data

○ ○ ○

GREEN GAMMA DATA TRANSFER UGGW W

BLUE GAMMA DATA TRANSFER UGBW W

RED GAMMA DATA READ UGRR W 1-16 xxxx

···

xxxx

(xxxx: 32 pieces)

xxxx: 0000-1023

xxxx: User data of 32 pieces

GREEN GAMMA DATA READ UGGR W 1-16

BLUE GAMMA DATA READ UGBR W 1-16

USER DATA INITIALIZE UGRS W 0 Initialize the user data.

USER DATA SAVE UGSV W 0 Save the user data in the monitor.

Controlling the Monitor with a PC (RS-232C)

WhenthePN-ZB01(optional)isattached,yourmonitorcan

beconnectedtoaLANallowingyoutocontrolitfromaPCon

the LAN.

Youcanalsocongurethemonitortosende-mailnotication

when it has a problem.

TheconnectionrequiresacommerciallyavailableLANcable

(UTPcable,Category5,straightthrough).

Hub

LAN terminal

LAN cable (commercially available, straight)

Network (LAN)

TIPS

• YoumustassignanIPaddresstothemonitorbyfollowing

the procedures in “Settings to connect to a LAN”. (See the

description on the right.)

• YourPCmustbeinstalledwithInternetExplorer(version7.0

or later).

• TocontrolthemonitorviaLAN,setRS-232C/LANSELECT

to LAN. (See page 23.)

• YoucannotuseRS-232CandLANcontrolsimultaneously.

Initializing personal information

• WhenthePN-ZB01(optional)isattached,personal

informationsuchase-mailaddressescanberegisteredin

themonitor.Beforetransferringordisposingofthemonitor,

initializeallsettingsbyselectingALLRESET1.(See

page29.)NotethatALLRESET2willnotinitializee-mail

addresses and other settings.

Controlling the Monitor with a PC (LAN)

Settings to connect to a LAN

Set the monitor’s IP address and subnet mask to match the

settings of your LAN.

ThesesettingscanbemadeoneitherthemonitororaPC

connected to the monitor.

ThesettingsdependonthecongurationofyourLAN.Ask

your LAN administrator for details.

■ To set on the monitor

SetRS-232C/LANSELECTontheSETUPmenutoLAN,and

thensettheLANSETUPoptions.(Seepage23.)

Aftersettingeachitem,selectSETandpress

DHCP CLIENT

IfyourLANhasaDHCPserverandyouwishtoobtainan

address automatically, change this setting to ON.

Tosettheaddressmanually,setthistoOFF.

IP ADDRESS

IftheDHCPCLIENTissettoOFF,specifyanIPaddress.

Press

or to select items, and press or to

change the values.

SUBNET MASK

IftheDHCPCLIENTissettoOFF,specifythesubnetmask.

Press

or to select items, and press or to

change the values.

DEFAULT GATEWAY

IftheDHCPCLIENTissettoOFF,specifythedefault

gateway.

Ifyouarenotusingagateway,specify“0.0.0.0”.

Press

or to select items, and press or to

change the values.

RESET

Resets the values of the LAN settings to the factory preset

values.

Select ON and then press

TIPS

• WhentheIPaddressissetmanually,theIPaddressesof

themonitorconnectedtotheRS-232Coutputterminal and

the daisy chain of connected monitors that follows can be

assigned automatically. (See page 23.)

■ To set from a PC

WhenthemonitorisconnectedtoaPC,LANsettingscanbe

conguredviaPC.

Set up process

(1)ConnectyourmonitortoaPC

(2)SpecifythePC’sIPaddress

(3)Congurethemonitor’sLANsettings

(1) Connecting your monitor to a PC

ConnectacommerciallyavailablecrossoverLANcable

(UPTcable,Category5)totheLANportonthePCandthis

monitor.

LAN cable

(commercially available, crossover)

To LAN terminal

LAN terminal

(2) Specifying the PC’s IP address

Tocongurethemonitor’sLANsettings,youmusttemporarily

changethesettingsonthePC.

ThisexplanationisbasedonWindows7.

1. LogontothePCwithanadministratoraccount.

2. Click[Start],andthenclick“ControlPanel”.

3. Click“Viewnetworkstatusandtasks”in“Networkand

Internet”.

In“ClassicView”,click“NetworkandSharingCenter”.

4. Click“LocalAreaConnection”andthen“Properties”.

5. Click“InternetProtocolVersion4(TCP/IPv4)”andthen

“Properties”.

6. Make a note of the current IP address, subnet mask, and

default gateway settings.

Make sure you write this information now as you will

be changing the IP address, subnet mask, and default

gateway settings back to these settings afterwards.

7. Temporarily change the IP address and subnet mask.

To access the monitor as it is shipped from the factory, set

as follows.

• IPAddress:192.168.150.1

• SubnetMask:255.255.255.0

• DefaultGateway:(leaveblank)

8. Click[OK]andthenrebootthePC.

TIPS

• Thismonitorisfactorypresetasshownbelow.

(WhenDHCPCLIENTissettoOFF)

 IPAddress :192.168.150.2

 SubnetMask :255.255.255.0

 DefaultGateway :0.0.0.0

(3) Conguring the monitor’s LAN settings

AccessthemonitorusingInternetExplorer.

Controllingthemonitor

1. TurnthepowerONtothemonitor.

2. SetRS-232C/LANSELECTontheSETUPmenutoLAN.

3.SetDHCPCLIENTtoOFFinLANSETUPontheSETUP

menu.

PCoperation

4. LaunchInternetExplorer,inthe“Address”boxtype

“http://192.168.150.2/”andpresstheEnterkey.

You will be prompted to enter a user name and password.

5. Leavetheusernameandpasswordboxesblankandclick

[OK].

Controlling the Monitor with a PC (LAN)

6. Click on “LAN SETUP” under NETWORK.

7. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc.

DHCP CLIENT

If your LAN has a DHCP server and you wish to obtain an

address automatically, change this setting to “ON”.

To set the address manually, set this to “OFF”.

IP ADDRESS

If the DHCP CLIENT is set to “OFF”, specify an IP address.

SUBNET MASK

If the DHCP CLIENT is set to “OFF”, specify the subnet mask.

DEFAULT GATEWAY

If the DHCP CLIENT is set to “OFF”, specify the default gateway.

If you are not using a default gateway, specify “0.0.0.0”.

8. When the setting is changed, click [Apply].

9. Check the message and click [OK].

. Exit Internet Explorer.

11.

Restore the PC’s IP address jotted in Step 6, “(2)

Specifying the PC’s IP address”.

12.

Connect the monitor and the PC to the LAN.

Caution

• Wait10secondsafterclicking[OK]beforeproceeding.

• Whenoperatingusingtheremotecontrolunitorsimilar,

click [Refresh].

TIPS

• WhentheIPaddressissetmanually,theIPaddressesof

the monitor connected to the RS-232C output terminal and

the daisy chain of connected monitors that follows can be

assigned automatically. (See page 23.)

Controlling with a PC

■ Basic operation

You use Internet Explorer on a PC on the LAN to control the

monitor.

1. Launch Internet Explorer on the PC.

In the “Address” box, type “http://” followed by your monitor’s

IP address followed by “/”, then press the Enter key.

YoucanconrmtheIPaddresswiththeDISPLAYfunction.

When prompted to enter a user name and password, type

theusernameandpasswordthatyouspeciedinthe

security settings (see page 46), and click [OK].

If you did not make any security settings, leave the spaces

blank and click on [OK].

3. You can check, control, and change the monitor’s status

and settings by clicking the menu items on the left side of

the screen.

• Ifyouseean[Apply]buttonnexttoasetting,clickitafter

you change that setting.

TIPS

• Seepages45to49fordetailsoneachsetting.

• Ifyouclick[Refresh]beforethescreennishesupdating

the current display, the “Server Busy Error” will appear.

Wait for a moment before operating your monitor again.

• Youcannotoperatethemonitorwhileitiswarmingup.

• If“DHCPCLIENT”issetto“ON”,press

DISPLAY

on the

remote control unit two times and then check the monitor’s

IP address.

Controlling the Monitor with a PC (LAN)

■ INFORMATION

Information about this monitor appears.

■ CONTROL

You can control the operations corresponding to the buttons

(

POWER

INPUT

SIZE

)ontheremotecontrolunit.(Seepage18.)

TIPS

• Instandbymode,PowerONistheoperationavailable.

■ ADJUSTMENT

Youcanadjustthesesettingswhicharealsoavailableonthe

monitor’s menu.

• SCREEN(Seepage21.)

• PICTURE(Seepage21.)

• PICTURE(ADVANCED)(Seepage28.)

• AUDIO(Seepage22.)

• SETUP(Seepage22.)

• OPTION(Seepage23.)

• SCHEDULE(Seepage27.)

• MULTI(Seepage24.)

• PIP/PbyP(Seepage25.)

• FUNCTION(Seepage29.)

TIPS

• AfterchangingDISPLAYCOLORPATTERNtoOFF,click

[Refresh]tocorrectlyretrievethestatusofthemonitor.

Controlling the Monitor with a PC (LAN)

■ NETWORK (LAN SETUP)

This screen allows you to set the settings necessary when the

monitor is connected to a LAN.

DHCP CLIENT

IfyourLANhasaDHCPserverandyouwishtoobtainan

address automatically, change this setting to “ON”.

Tosettheaddressmanually,setthisto“OFF”.

IP ADDRESS

IftheDHCPCLIENTissetto“OFF”,specifyanIPaddress.

SUBNET MASK

IftheDHCPCLIENTissetto“OFF”,specifythesubnet

mask.

DEFAULT GATEWAY

IftheDHCPCLIENTissetto“OFF”,specifythedefault

gateway.

Ifyouarenotusingadefaultgateway,specify“0.0.0.0”.

DNS SERVER

SpecifytheDNSserveraddress.

IfyouarenotusingaDNSserver,specify“0.0.0.0”.

RESET

Clicking[Execute]returnsalloftheLANSETUPsettings

tothefactory-presetvaluesexceptfortheDNSSERVER

setting.

TIPS

• WhentheIPaddressissetmanually,theIPaddressesof

themonitorconnectedtotheRS-232Coutputterminal and

the daisy chain of connected monitors that follows can be

assigned automatically. (See page 23.)

■ NETWORK (SECURITY)

Thisscreenallowsyoutospecifythesecurity-relatedsettings.

USER NAME / PASSWORD

Sets up a user name and password to restrict access to this

monitor.

Afterenteringausernameandpassword,click[Apply].

ACCEPT IP ADDRESS

You can limit access to this monitor by registering IP

addressesofPCsthatshouldhaveaccess.

Tolimitaccess,specifytheoption“FromonlyspecicIP

addresses”.Otherwise,toallowaccessfromanyPC,specify

“All IP Addresses”.

IP ADDRESS 1 to 3

If“ACCEPTIPADDRESS”issetto“FromonlyspecicIP

addresses”, enter the IP addresses that you want to allow.

TIPS

• TheUSERNAMEandPASSWORDcanbeupto8

alphanumeric characters or symbols.

• Tocanceltheusernameand/orpasswordafterithasbeen

set,maketheboxemptyandclick[Apply].

Controlling the Monitor with a PC (LAN)

■ NETWORK (GENERAL)

This screen allows you to specify the general LAN settings.

MONITOR NAME

Specify a name for this monitor as it should appear on the

InternetExplorerscreen.

AUTO LOGOUT TIME

Specify the time (in minutes) to elapse before automatically

disconnecting this monitor from the network.

Specifyinminutesfrom1to65535.Avalueof‘0’willdisable

this function.

DATA PORT

SpecifytheTCPportnumbertouseforexchangingdatawith

the monitor.

Specifyavaluefrom1025to65535.

SEARCH PORT

Specify the port number to use when searching for this

monitor.

Specifyavaluefrom1025to65535.

INSTALLATION INFORMATION (NAME/LOCATION)

Specify the information to display for this monitor in the

InternetExplorerwindow.

TIPS

• TheMONITORNAMEcanbeupto16alphanumeric

characters or symbols.

• Enterupto50charactersintheNAMEeldinthe

INSTALLATIONINFORMATION.

• Enterupto100charactersintheLOCATIONeldinthe

INSTALLATIONINFORMATION.

■ MAIL (ORIGINATOR)

Thisscreenallowsyoutocongurethee-mailsentperiodically

or when the monitor has an error.

ThesettingsdependonthecongurationofyourLAN.Ask

your LAN administrator for details.

SMTP SERVER

SpecifytheSMTPserveraddressforsendinge-mail.

* Whenusingadomainname,makesuretospecifythe

DNSSERVER as well. (See page 46.)

ORIGINATOR E-MAIL ADDRESS

Specifythee-mailaddressforthismonitor.

Thisaddressbecomesthee-mailaddressoftheoriginator.

ORIGINATOR NAME

Specify the name for the originator.

Thisnameappearsinthe“OriginatorName”eldofthe

e-mail.

AUTHENTICATION

Specify the authentication method to use when sending

e-mail.

POP SERVER

Ifthe“AUTHENTICATION”methodis“POPbeforeSMTP”,

specify the POP server address.

ACCOUNT NAME / PASSWORD

Ifthe“AUTHENTICATION”methodis“POPbeforeSMTP”,

specify the account name and password to connect to the

POP server.

TIPS

• Youcanenterupto64alphanumericcharactersorsymbols

fortheORIGINATORE-MAILADDRESS,ORIGINATOR

NAME,ACCOUNTNAME,andPASSWORD.

• TheSMTPSERVERandPOPSERVERcanbeupto64

characters.

Thefollowingcharacterscanbeused:a-z,A-Z,0-9,-,.

Controlling the Monitor with a PC (LAN)

■ MAIL (RECIPIENT)

Thisscreenallowsyoutospecifytherecipientsofthee-mail

sent periodically or when the monitor has an error.

RECIPIENT E-MAIL ADDRESSES

Specifythee-mailaddressestosenderrornoticatione-mail

to.

CONDITION

Specify the conditions to send mails.

WhenyoucheckPERIODICAL,specifythedateandtimeto

sendthemailsinthePERIODICALsetting.

CONFIRMATION

Sendsteste-mail.

Thisallowsyoutoconrmthatthee-mailsettingsare

conguredproperly.

Attach the log le to a TEMPERATURE/HARDWARE error

e-mail.

Whenthisoptionischecked,alogisaddedtothemailwhich

notiesatemperatureorstatuserror.

TIPS

• TheRECIPIENTE-MAILADDRESSEScanbeupto64

alphanumeric characters or symbols.

Controlling the Monitor with a PC (LAN)

■ MAIL (PERIODICAL)

WhenPERIODICALforCONDITIONofMAIL(RECIPIENT)is

checked, set the date and time to send the mail.

DAY OF THE WEEK

Specify the day of the week to send the periodical mails.

TIME

Specify the time of the day to send the periodical mails.

Caution

• Donotturnoffthemainpowerwhenyousettosendthe

periodical mails.

• Specifythecorrectdateandtime.(Seepage23.)

If the date and time settings are incorrect, the periodical

mail is not sent properly.

• Regularlyconrmthatthespecieddateandtimeis

correct.

• WhenLOWPOWERisselectedforSTANDBYMODE,

periodical mails will not be sent in standby mode.

Controlling the Monitor with a PC (LAN)

■ SNMP

YoucanconguresettingsrelatedtoSNMP.

SNMP SETTING

Set whether to enable or disable SNMP.

VERSION

Set the version of the SNMP to be supported.

COMMUNITY NAME 1 to 3

Setthenameofthecommunityrequiredfortheaccess.

USER 1 to 3

Set the user name, password, authentication method and

otheroptionsrequiredforaccess.

TRAP SETTING

Set whether to enable or disable the trap function.

Whenthisfunctionisenabled,atrapwillbesentwhenthe

monitor is turned on.

TRAP SETTING OF AUTHENTICATION ERROR

Setwhetherthetrapfunctionsendsanoticationwhen

authentication fails.

TRAP ADDRESS & PORT

Set the destination address and port number of the

noticationsentbythetrapfunction.

Caution

• AfteryousetSNMP,click[Switchthemainpowerof

monitoroffandonnow.]orturnoffthemonitorandthen

turnitonagainwiththemainpowerswitch.Whenthe

monitorrestarts,waitabout30secondsandthenstartthe

next operation.

• IftheIPaddressischangedwhiletheSNMPfunctionis

operational, turn off the monitor and then turn it on again

with the main power switch.

TIPS

• DependingontheSNMPsettings,ashortdelaymayoccur

before the SNMP is usable. (About 2 minutes)

• Upto16alphanumericlettersandsymbolscanbeusedfor

the community name, user name and password.

■ SERVICE & SUPPORT

(URL INFORMATION)

YoucandisplayaspecicURLintheURLINFORMATION

eldontheINFORMATIONscreenwhenanerroroccursin

themonitor.(Seepage45.)

URL INFORMATION

EntertheURLtodisplayontheINFORMATIONscreenwhen

an error occurs on the monitor.

Up to 64 alphanumeric characters or symbols can be used.

CONDITION

Specify the condition to display the URL.

CONFIRMATION

ThehomepageofthespeciedURLisdisplayed.

You can check whether the URL you entered is correct.

TIPS

• Itisalsopossibletospecifythemessagetext,suchasthe

name of a contact or a telephone number, to be displayed

instead of the linked URL.

Troubleshooting

If you are experiencing any problem with your display, before

calling for service, please review the following troubleshooting

tips.

There is no picture or sound.

• Isthepowercorddisconnected?(Seepage14.)

• Isthemainpowerswitchoff?(Seepage16.)

• Isthemonitorinstandbymode(thepowerLEDilluminating

inorange)?(Seepage16.)

• Makesurecorrectinputmodeisselected.(Seepage18.)

• Ifanyexternalequipmentisconnected,makesurethe

equipmentisoperating(playingback).

Remote control does not work.

• Arethebatteriesinsertedwithpolarity(+,-)aligned?(See

page15.)

• Arethebatteriesexhausted?

• Pointtheremotecontrolunittowardthemonitor’sremote

controlsensor.(Seepage15.)

• Isthemenudisplayhiddenorisoperationdisabled?(See

page29.)

Sound from left and right speakers is reversed.

Sound is heard from only one side.

• Areaudiocablesconnectedproperly?(Seepages12to13.)

• Makesureaudiocablesforexternalspeakersareconnected

properly: left and right cables may be reversed or one of the

twocablesmaynotbeconnected.(Seepage13.)

• CheckthesettingofBALANCEforAUDIOmenu.(See

page22.)

There is a picture but no sound.

• Isthesoundmuted?

• Makesurethevolumeisnotsettominimum.

• Areaudiocablesconnectedproperly?

• IsthesettingofAUDIOSELECTontheOPTIONmenu

correct?(Seepage23.)

• IsthesettingofSPEAKERSELECTontheSETUPmenu

correct?(Seepage23.)

Unstable video.

• Thesignalmaybeincompatible.

• TrytheautomaticscreenadjustmentwhenthePCD-sub

inputterminalorPCRGBinputterminalsareused.

The video from the PC/AV HDMI input terminal does not

appear properly.

• IsthesettingforHDMIofINPUTSELECTontheOPTION

menucorrect?(Seepage23.)

• IstheHDMIcableHDMIstandardcompliant?Themonitor

willnotworkwithcablesthatarenotstandardcompliant.

• Istheinputsignalcompatiblewiththismonitor?(Seepage

54.)

The video from the PC/AV DVI-D input terminal does not

appear properly.

• IsthesettingforDVIofINPUTSELECTontheOPTION

menucorrect?(Seepage23.)

• Istheinputsignalcompatiblewiththismonitor?(Seepage

54.)

• Turnoffthepowertotheconnectedequipmentandthen

turn the power on again.

• Ifthemonitorsareconnectedinadaisychain,turnoffthe

power to all the monitors connected in a daisy chain and

then turn the power on again.

The video from PC D-SUB, PC RGB, AV COMPONENT, or

AV VIDEO does not appear correctly.

• IsthesettingforBNCorD-SUBofINPUTSELECTonthe

OPTIONmenucorrect?(Seepage23.)

• Istheinputsignalcompatiblewiththismonitor?(Seepage

54.)

Control buttons do not work.

There is no picture.

• Loadnoisesfromoutsidemaybeinterferingwithnormal

operation.Turnoffthepowerandturnitonafterwaitingat

least5seconds,andthenchecktheoperation.

The input mode changes automatically.

• WhentheAUTOINPUTCHANGEisONandnosignal

ispresentinaselectedinputmode,theAUTOINPUT

CHANGEautomaticallychangestheselectedmodetoa

mode where a video signal is present.

 Theinputmodemaychangeinthefollowingcases:

-Whenacomputerisinstandbymode.

-Whenvideoplayisstoppedwithaplaybackdevice.

Power LED ashes red.

“STATUS [xxxx]” appears in the corner of the screen.

• Hardwarehasaproblem.Turnoffthemonitorandrequest

repairfromyourSHARPdealer.

(WhenSTATUSALERTissettoOSD&LED.Thisvaries

dependingonthesetting.)

When “AUTO DIMMING” is displayed.

• Whentheinternaltemperatureofthemonitorrises

excessively,thebrightnessofthebacklightautomatically

decreases in order to prevent a further temperature rise. If

you attempt to use

toadjustthebrightnesswhile

themonitorisinthisstate,“AUTODIMMING”isdisplayed

and you cannot change the brightness.

• Removethecauseoftheexcessivetemperaturerise.

The monitor makes a cracking sound.

• Youmayoccasionallyhearacrackingsoundfromthe

monitor.Thishappenswhenthecabinetslightlyexpands

andcontractsaccordingtochangeintemperature.This

doesnotaffectthemonitor’sperformance.

The Power LED is ashing in red and green alternately.

When “TEMPERATURE” is displayed in the corner of the

screen.

• Whentheinternaltemperatureofthemonitorrises

excessively, the brightness of the backlight decreases

automaticallyinordertopreventhigh-temperature-

relatedproblems.Whenthisoccurs,“TEMPERATURE”is

displayedonthescreenandthePowerLEDashesred

andgreenalternately.(WhenTEMPERATUREALERTis

settoOSD&LED.Thisvariesdependingonthesetting.)

• Iftheinternaltemperaturerisesfurther,themonitor

automaticallyentersstandbymode.(ThePowerLED

continuesashingredandgreenalternately.)

• Removethecauseoftheexcessivetemperaturerise.

-Ifthemonitorentersstandbymodeduetoarisein

temperature, to return to normal display, turn the power

switch off and then back on again. The monitor, however,

will enter standby mode again if the cause of the

temperature rise is not eliminated. (See page 8.)

-Checkwhetherthemonitorisplacedatalocationwhere

aquickriseintemperatureislikely.Internaltemperature

risesquicklyiftheventsonthemonitorareblocked.

-Internaltemperaturerisesquicklyifdustaccumulates

inside the monitor or around the vents. Remove dust if

possible.AskSHARPdealeraboutremovinginternaldust.

Troubleshooting

Specications

Product Specications

Model PN-E702

LCD component

70" Class [69-1/2 inch (176.6cm) diagonal] TFT LCD

Max. resolution (pixels)

1920 x 1080

Max. colors

Approx. 1.06 billion colors

Pixel pitch

0.802 mm (H) × 0.802 mm (V)

Viewing angle

176° right/left/up/down (contrast ratio ≥ 10)

Screen active area inch (mm)

60-9/16 x 34-1/16 (1538.9 x 865.6)

Computer input signal

Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75

]

Sync signal

Horizontal/vertical separate (TTL: positive/negative), Sync-on-green,

Composite sync (TTL: positive/negative)

Video color system

NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAM

Plug and play

VESA DDC2B

Power management

VESA DPMS, DVI DMPM

Input terminals

PC/AV

Digital

HDMI x 1

Analog

Mini D-sub 15 pin, 3 rows x 1

Audio

3.5 mm mini stereo jack x 1

Serial (RS-232C)

D-sub 9 pin x 1

When PN-ZB01

(optional) is

attached

PC/AV

Digital

DVI-D 24 pin (HDCP compatible) x 1

Analog

BNC

x 1

Composite video

BNC x 1

S-video

x 1

Component BNC (Y, Cb/Pb, Cr/Pr) *

x 1

Audio

RCA pin (L/R) x 2

Output terminals

Audio

RCA pin (L/R) x 1

Serial (RS-232C)

D-sub 9 pin x 1

When PN-ZB01

(optional) is

attached

PC/AV

Digital

DVI-D 24 pin x 1

External speaker 7 W + 7 W

]

LAN terminal

[

When PN-ZB01 (optional) is attached

]

10 BASE-T/100 BASE-TX

Speaker output 7 W + 7 W

Power requirement AC 100 V - 240 V, 2.8 A, 50/60 Hz

Operating temperature

32°F to 104°F (0°C to 40°C)

Operating humidity 20% to 80% (no condensation)

Power consumption

(Maximum / input signal waiting mode

/ standby

mode

)

235 W / 1.0 W / 1.0 W

Power consumption

[

When PN-ZB01 (optional) is attached

]

240 W

Dimensions (excluding protrusions) inch (mm)

Approx. 63-9/16 (W) x 3-15/16 (D) x 37-5/16 (H) (1,615 x 100 x 947)

Weight lbs. (kg)

Approx. 110.2 (50)

Weight [PN-ZB01 (optional)] lbs. (kg)

Approx. 1.102 (0.5)

*1 Cannot be used simultaneously.

*2 Does not support plug and play.

*3 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP.

In such cases, please check the temperature condition specied by the optional equipments.

*4 When AUTO INPUT CHANGE is set to OFF.

*5 When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W

As a part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement

without prior notice. The performance specication gures indicated are nominal values of production units. There may be some deviations from

these values in individual units.

Specications

Dimensional Drawings

Note that the values shown are approximate values.

Unit: inch [mm]

3-15/16

[100]

3-15/16

[100]

3-15/16

[100]

1-11/16

[43.5]

[76.5]

Opening width (60-13/16 [1545])

59-9/16 [1513]

63-9/16 [1615]

Opening height (34-1/4 [870])

37-5/16 [947]

7-7/8 [200]

1-15/16 [50]

7-7/8

[200]

7-7/8

[200]

VESA holes *

When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method.

SHARP recommends using M6 screws and tighten the screws.

Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in

serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch

(8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times

or more the weight of the monitor.

Power management

This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in

order for the monitor’s power management function to work.

DPMS: Display Power Management Signaling

DPMS Screen

Power

consumption

Hsync Vsync

ON STATE Display 235 W*

Yes Yes

STANDBY

display

1.0 W*

No Yes

SUSPEND Yes No

OFF STATE No No

*1 When PN-ZB01 (optional) is not connected.

*2 When AUTO INPUT CHANGE is set to OFF.

DMPM: Digital Monitor Power Management

DMPM Screen

Power

consumption

Monitor ON Display 235 W*

Active OFF No display 1.0 W*

DDC (plug and play)

The monitor supports the VESA DDC (Display Data Channel) standard.

DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters

is exchanged between the two. This function can be used if the computer supports DDC and it has been congured to detect

plug-and-play monitors.

There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.

Compatible signal timing (PC)

VESA

Wide

US TEXT

Sun

Screen resolution Hsync VsyncDot frequency

Digital

640 × 480

800 × 600

848 × 480

1024 × 768

1152 × 864

1280 × 768

1280 × 800

1280 × 960

1280 × 1024

1360 × 768

1400 × 1050

1440 × 900

1600 × 1200

1680 × 1050

1920 × 1200

1280 × 720

1920 × 1080

720 × 400

1024 × 768

1152 × 900

1280 × 1024

1600 × 1000

31.5kHz

37.9kHz

37.5kHz

35.1kHz

37.9kHz

48.1kHz

46.9kHz

31.0kHz

48.4kHz

56.5kHz

60.0kHz

67.5kHz

47.8kHz

60.3kHz

49.7kHz

60.0kHz

64.0kHz

80.0kHz

47.7kHz

65.3kHz

55.9kHz

75.0kHz

65.3kHz

74.0kHz

44.7kHz

66.3kHz

67.5kHz

31.5kHz

48.3kHz

53.6kHz

56.6kHz

61.8kHz

71.8kHz

71.7kHz

81.1kHz

68.6kHz

60Hz

72Hz

75Hz

56Hz

60Hz

72Hz

75Hz

60Hz

70Hz

75Hz

60Hz

75Hz

60Hz

75Hz

60Hz

70Hz

60Hz

66Hz

70Hz

66Hz

76.2Hz

67.2Hz

76Hz

66Hz

25.175MHz

31.5MHz

36.0MHz

40.0MHz

50.0MHz

49.5MHz

33.75MHz

65.0MHz

75.0MHz

78.75MHz

108.0MHz

79.5MHz

102.25MHz

83.5MHz

108.0MHz

135.0MHz

85.5MHz

121.75MHz

106.5MHz

162.0MHz

146.25MHz

154.0MHz

74.4MHz

148.5MHz

28.3MHz

64.13MHz

70.4MHz

74.25MHz

94.88MHz

108.23MHz

117.01MHz

134.99MHz

135.76MHz

Yes

Analog

(D-SUB/RGB*

)

Yes

DVI*

HDMI

Yes

*1 Displays a reduced image, except in Dot by Dot. In Dot by Dot, the image will be cut down to panel size then displayed.

*2 Available when the PN-ZB01 (optional) is attached.

* Allarecompliantonlywithnon-interlaced.

* DependingontheconnectedPC,imagesmaynotbedisplayedproperlyevenifthecompatiblesignaldescribedaboveisinput.

* ThefrequencyvaluesfortheSunarereferencevalues.

Compatible signal timing (AV)

Screen resolution Frequency DVI-D* HDMI Component

1920×1080p 24Hz - Yes -

50Hz Yes Yes Yes

59.94Hz Yes Yes Yes

60Hz Yes Yes Yes

1920×1080i 50Hz Yes Yes Yes

59.94Hz Yes Yes Yes

60Hz Yes Yes Yes

1280×720p 50Hz Yes Yes Yes

59.94Hz Yes Yes Yes

60Hz Yes Yes Yes

720×576p 50Hz Yes Yes Yes

720×480p 59.94Hz Yes Yes Yes

60Hz Yes Yes Yes

640×480p(VGA) 59.94Hz Yes Yes -

60Hz Yes Yes -

720(1440)×576i 50Hz - Yes Yes

720(1440)×480i 59.94Hz - Yes Yes

60Hz - Yes Yes

*AvailablewhenthePN-ZB01(optional)isattached.

Specications

PC/AV DVI-D input terminal pins

(DVI-D 24 pin)

No. Function No. Function

1 TMDSdata2- 13 N.C.

2 TMDSdata2+ 14 +5V

3 TMDSdata2/4shield 15 GND

4 N.C. 16 Hot-plugdetection

5 N.C. 17 TMDSdata0-

6 DDCclock 18 TMDSdata0+

7 DDCdata 19 TMDSdata0/5shield

8 N.C. 20 N.C.

9 TMDSdata1- 21 N.C.

10 TMDSdata1+ 22 TMDSclockshield

11 TMDSdata1/3shield 23 TMDSclock+

12 N.C. 24 TMDSclock-

PC D-sub input terminal pins

(Mini D-sub 15 pin)

No. Function No. Function

1 Red video signal input 9 +5V

2 Greenvideosignalinput 10 GND

3 Bluevideosignalinput 11 N.C.

4 N.C. 12 DDCdata

5 GND 13 Hsyncsignalinput

6 GNDforredvideosignal 14 Vsyncsignalinput

7 GNDforgreenvideosignal 15 DDCclock

8 GNDforbluevideosignal

PC/AV DVI-D output terminal pins

(DVI-D 24 pin)

No. Function No. Function

1 TMDSdata2- 13 N.C.

2 TMDSdata2+ 14 +5V

3 TMDSdata2/4shield 15 GND

4 N.C. 16 Hot-plugdetection

5 N.C. 17 TMDSdata0-

6 DDCclock 18 TMDSdata0+

7 DDCdata 19 TMDSdata0/5shield

8 N.C. 20 N.C.

9 TMDSdata1- 21 N.C.

10 TMDSdata1+ 22 TMDSclockshield

11 TMDSdata1/3shield 23 TMDSclock+

12 N.C. 24 TMDSclock-

PC/AV HDMI input terminal pins

(HDMI

Connector)

No. Function No. Function

1 TMDSdata2+ 11 TMDSclockshield

2 TMDSdata2shield 12 TMDSclock-

3 TMDSdata2- 13 CEC

4 TMDSdata1+ 14 N.C.

5 TMDSdata1shield 15 SCL

6 TMDSdata1- 16 SDA

7 TMDSdata0+ 17 DDC/CECGND

8 TMDSdata0shield 18 +5V

9 TMDSdata0- 19 Hot-plugdetection

10 TMDSclock+

RS-232C input terminal pins

(D-sub 9 pin)

No. Function No. Function

1 N.C. 6 N.C.

2 Transmitted data 7 N.C.

3 Received data 8 N.C.

4 N.C. 9 N.C.

5 GND

RS-232C output terminal pins

(D-sub 9 pin)

No. Function No. Function

1 N.C. 6 N.C.

2 Received data 7 N.C.

3 Transmitted data 8 N.C.

4 N.C. 9 N.C.

5 GND

• Wheninstalling,removingormovingthemonitor,ensurethatthisiscarriedoutbyatleast2people.

• Besuretouseawall-mountbracketdesignedordesignatedformountingthemonitor.

• Thismonitorisdesignedtobeinstalledonaconcretewallorpillar.Reinforcedworkmightbenecessaryforsomematerials

suchasplaster/thinplasticboard/woodbeforestartinginstallation.

Thismonitorandbracketmustbeinstalledonawallwhichcanendureatleast4timesormoretheweightofthemonitor.

Installbythemostsuitablemethodforthematerialandthestructure.

• ToattachaVESA-compliantmountingbracket,useM6screwsthatare5/16inch(8mm)to3/8inch(10mm)longerthanthe

thicknessofthemountingbracket.

• Whenmovingthemonitor,besuretoholditwiththehandlesandtheunitbottom.DonotholdtheLCDpanel.Thismaycause

productdamage,failure,orinjury.

• Aftermounting,pleasecarefullyensurethemonitorissecure,andnotabletocomeloosefromthewallormount.

• DonotuseanyscrewholesotherthanVESAholesforinstallation.

Mounting Precautions

(For SHARP dealers and service engineers)

PN-E702 Mu EN11K(1)

PN-E702 Sharp

Product's Documents

User Manual

Specifications

Sharp PN-E702 Questions and Answers

Related Products

Rowenta TN6000F4 FOREVER SHARP TN6000

Rowenta TN6010F4 FOREVER SHARP TN6010

Rowenta TN6030F4 FOREVER SHARP SP TN6030

Sharp SDW6768SMS 24" Top Control Stainless Steel Dishwasher with Pocket Handle and Auto Door Open Feature

Sharp SDY6768SMS 24" Top Control Stainless Steel Dishwasher with Auto Door Open and Quiet 44dB Operation

Sharp 2T-C32GH3000X 32 Inch Google TV