Loading ...
2
INSTALLATION REQUIREMENTS
Tools and Parts
Tools Needed
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
Measuring tape
Pencil
Masking tape or
thumbtacks
Scissors
No. 2 Phillips screwdriver
No. 3 Phillips screwdriver
for ¹⁄₄ - 20 x 3" (7.62 cm)
bolts
Drill
³⁄₁₆" (5 mm), ³⁄₈" (10 mm),
⁵⁄₈" (16 mm) drill bits
³⁄₄" (19 mm) hole saw
Diagonal wire cutting pliers
Stud finder
⁷⁄₁₆" (11.11 mm) socket
wrench (or box wrench) for
¹⁄₄" x 2" (6.35 mm x
5.08 cm) lag screws
1½" (3.8 cm) diam. hole
drill bit for wood or metal
cabinet
Keyhole saw
Caulking gun and
weatherproof caulking
compound
Duct tape
Parts Supplied
For information on reordering, see the “Replacement Parts”
section.
NOTE: The hardware items listed here are for wood studs.
For other types of wall structures, be sure to use appropriate
fasteners.
A
B
C
D E F
G
H
A. ³⁄₁₆
-24 x 3" (7.62 cm) round-head
bolts (2)
¹⁄₄ daeh-talf )mc 26.7( "3 x 02-
bolts (2)
B.
Not Shown:
Upper cabinet template
Mounting plate (attached to
back of microwave oven)
Cardboard template (part of
packaging) or wall template
Aluminum grease filters
Charcoal filters (Depending on
model, charcoal filters may
not be included. See User
Instructions.)
NOTE: Depending on model, aluminum grease filter and charcoal
filter may be combined
Materials Needed
Standard fittings for wall or oof venting. See the “Venting
Design Specifications” section
Location Requirements
Check the opening where the microwave oven will be installed.
The location must provide:
Minimum installation dimensions. See the “Installation
Dimensions” illustration.
Minimum one 2" x 4" (50.8 x 101.6 mm) wood wall stud and
minimum ³⁄₈" (10 mm) thickness drywall or plaster/lath within
cabinet opening.
Support for weight of 150 lbs (68 kg) which includes
microwave oven and items placed inside the microwave
oven and upper cabinet.
Grounded electrical outlet inside upper cabinet. See the
“Electrical Requirements” section.
NOTES:
If ins talling the microwave oven near a left sidewall, make
su re there is at least 6" (15.2 cm) of clearance between the
wall and the microwave oven so that the door can open fully.
emo S models have a pocket handle. If installing the microwave
nea r a right side wall, make sure there is at least 3 inches of
clearance between wall and microwave oven so you can
grab the handle integrated inside the door.
S ome cabinet and building materials are not designed to
withstand the heat pro
duced by the microwave oven for
cooking. Check with your builder or cabinet supplier to make
sure that the materials used will not discolor , delaminate, or
sustain other damages.
Special Requirements
For Wall Venting Installation Only:
Cutout must be free of any obstructions so that the vent fit
properly and the damper blade opens freely and fully.
For Roof Venting Installation Only:
If you are using a rectangular-to-round transition piece,
the 3" (7.6 cm) clearance needs to exist above the microwave
oven so that the damper blade can open freely and fully.
See “Rectangular to Round Transition” illustration in the
“Venting Design Specifications” section .
Remove Cardboard Template
The cardboard piece from the top of t he microwave oven
packaging is perforated. The piece inside the perforation
is for use as a rear wall template.
Depending on your model, skip "Remove Cardboard
Template" steps if full carton box is used for packing. But
use the wall template for "Mark Rear Wall" part of the
installation.
1. Cut along the perforation to separate the template from the
rest of the cardboard packaging.
2. Set the cardboard template to the side and refer to it during
the “Mark Rear Wall” part of installation.
F.
G.
H.
C. Washers (2)
D.
³⁄₁₆" (5 mm) toggle nuts (2)
E.
¹⁄₄ )mc 80.5 x mm 53.6( "2 x "
lag screws (2)
swercs latem teehS
(2)
)1( gnihsub droc ylppus rewoP
r o llaw rof( ylbmessa repmaD
roof venting)
6 x
3
/
8
"#
Loading ...
Loading ...
Loading ...