Loading ...
Loading ...
Important Safety Advice
When using elec
trical appliances, basic
precautions should be followed to reduce
the risk of fire, electric shock, and injury to
persons, including the following:
If the appliance is damaged, check
immediately with the supplier before
installation and operation.
Do not use this appliance in the immediate
surroundings of a bath, shower or swimming
pool.
Do not use outdoors.
This appliance must not be located
immediately above or below a fixed socket
outlet or connection box.
WARNING : The appliance carries
the Warning Symbol indicating that
it must not be covered or has a
Do not cover label. Do not cover
or obstruct in any way the heat outlet
grille located underneath the appliance
Overheating will result if the appliance is
accidentally covered. Do not place material
or garments on the appliance, or obstruct
the air circulation around the appliance, for
instance by curtains or furniture, as this could
cause overheating and a fire risk.
In the event of a fault unplug the heater.
Unplug the appliance when not required
for long periods. The supply cord must
be placed on the right hand side of the
heater away from the heat outlet
underneath the appliance.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the
appliance by a person responsible for their
safety.
Children shall not play with the appliance.
Cleaning and user maintenance shall not
be made by Children.
Children should be kept away unless
continuously supervised. Children shall not
turn on/off the appliance. Children shall
not plug in, regulate and clean the
appliance or perform user maintenance.
The appliance must be positioned so that
the plug is accessible.
Although this appliance complies with safety
standards, we do not recommend its use on
deep pile carpets or on long hair type of rugs.
If the supply cord is damaged it must be
replaced by the manufacturer or service
agent or similarly qualified person in order
CONNER CONCRETE
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
to avoid a hazard.
CAUTION: In order to avoid a hazard due to
inadvertent resetting of the thermal cut-out,
this appliance must not be supplied through
an external switching device, such as a timer,
or connected to a circuit that is regularly
switched on and off by the utility.
CAUTION - Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.
General
Unpack the heater carefully and retain the packaging for possible
future use, in the event of moving or returning the re to your
supplier.
The re incorporates a ame effect, which can be used with or
without heating, so that the comforting effect may be enjoyed
at any time of the year. Using the ame effect on its own only
requires little electricity.
Before connecting the heater check that the supply voltage is
the same as that stated on the heater.
Please note: Used in an environment where background
noise is very low, it may be possible to hear a sound which
is related to the operation of the ame effect. This is normal
and should not be a cause for concern.
Electrical Connection
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the
voltage marked on the heater must correspond to the supply
voltage.
Before switching on, please read the safety warnings and
operating instructions.
Controls - see Fig. 2
Three switches provide a choice of heat settings. The appliance
is in standby mode when the mains lead is plugged in. This is
indicated by the red neon behind the ame effect screen. The
two selector switches are in the ON position when the side with
the markings on (i.e. I, or II) are pushed in.
Push button switch 1 Controls the electricity supply to
the heater and ame effect.
If both selector switches 2 and 3 are in the OFF position, the
product works on ame effect only.
Selector switch 2 (I) Provides 750W heat output
Selector switch 3 (II) Provides 1500W output with switch
2 also pressed.
Thermostat (T) - see Fig. 3
In order to maintain a certain room temperature, set the controller
to ‘max.’. Operate the appliance at full power until the required
room temperature is reached. Set back the thermostatic controller
until the appliance switches off with an audible “click”. This
temperature will be kept almost constant by the thermostatic
control switching on and off automatically.Please note that the
appliance can only be switched on when the thermostat setting
is higher then the room temperature.
Loading ...