Loading ...
Loading ...
Loading ...
5
OPTIONS CAN BE
SELECTED
WITH
WHAT IT DOES ADDED TIME
TO CYCLE
ADDED WATER
GALLONS
(LITERS)
Delay displays how many hours before the cycle
will begin.
To delay the start:
1. Select a wash cycle and options.
2. Press DELAY. Each time you press Delay, it will
display the next available delay time.
3. Press START/REUME to begin the delay
countdown.
NOTE: If the door is opened, such as to add a
dish, the Start/Resume button must be pressed to
resume the delay countdown.
Available
with any
cycle
Delays start of
a cycle up to
24 hours.
NA NA
Raises the main wash temperature to improve
cleaning for loads containing tough, baked-on food.
Sensor
Heavy
Normal
Soak &
Clean
Raises the main
wash temperate
to135°F (57°C).
0:05 to 0:13 0 to 3.9
(0 to 14.6)
Dries dishes with heat. This option, with the use of
rinse aid, will provide better drying results. Plastic
items are less likely to deform when loaded in
the top rack. Use Heat Dry for optimum drying
performance. For air dry, Heat Dry LEDs are off.
Sensor
Heavy
Normal
1-Hour
Wash
Soak &
Clean
Uses a heating
element to speed
drying times. Heat
Dry option defaults to
On when any cycle is
selected, except for
1-Hour Wash.
NA NA
Sanitizes dishes and glassware in accordance
with NSF International NSF/ANSI Standard 184
for Residential Dishwashers. Certified residential
dishwashers are not intended for licensed food
establishments. Only sanitizing cycles have been
designed to meet the requirements of the NSF/
ANSI 184 performance standard for soil removal
and for sanitization efficacy. There is no intention,
either directly or indirectly, that all cycles on a
NSF/ANSI 184 certified dishwasher meet the NSF/
ANSI 184 performance standard for soil removal
and for sanitization efficacy.
The Sani Rinse indicator glows at the end of the
cycle if the Sani Rinse option was successfully
completed. If the indicator does not activate, it is
probably due to the cycle being interrupted.
Sensor
Heavy
Normal
Raises the main
wash temperate
to135°F (57°C)
and the final rinse
temperature to
156°F (69°C).
0:05 to 1:06 0 to 3.9
(0 to 14.6)
Use the Control Lock option to avoid unintended use of dishwasher between cycles or cycle and option changes during a cycle.
To turn on Control Lock, press and hold CONTROL LOCK for 3 seconds. Control Lock light will stay on for a short time, indicating
that it is activated. When the Lock indicator is lit, all buttons are disabled. If you press any button while your dishwasher is locked,
the light flashes three times. The dishwasher door can still be opened/closed while the controls are locked.
To turn off Control Lock, press and hold CONTROL LOCK for 3 seconds. Control Lock light turns off.
Control Purpose Comments
Press to start or
resume a wash
cycle.
If the door is opened during a cycle or the power is interrupted, the Start/Resume button
LED flashes. Cycle will not resume until Start/Resume is pressed and door is closed.
Push door firmly closed within 4 seconds of pressing Start/Resume.
Press to cancel
wash cycle.
Press and hold START/RESUME for 3 seconds. Close the door firmly. The dishwasher
starts a 2-minute drain (if needed). Let dishwasher drain completely.
To inform you that
the dishes have been
sanitized.
If you select the Sani Rinse option, when the cycle is finished, the Sanitized indicator
on the control panel glows. If your dishwasher did not properly sanitize your dishes,
the Sanitized indicator flashes at the end of the cycle. This can happen if the cycle is
interrupted or if water could not be heated to required temperature. The indicator goes
off when you open and close rhe door or press Start/Resume to Cancel.
Loading ...
Loading ...
Loading ...