Loading ...
Loading ...
Loading ...
14
Disabling Sounds
■ To turn off all control and dispenser sounds, press and hold
ICE and MEASURED FILL at the same time for 3 seconds.
■ To turn all sounds back on, press and hold ICE and
MEASURED FILL at the same time for 3 seconds again.
Dual Evaporator (on some models)
Some models come equipped with a dual sequential evaporation
system, which includes two separate evaporators for the
refrigerator and freezer compartments.
Dual evaporation results in higher humidity, which helps keep
foods in the refrigerator from spoiling as quickly and improves
food quality and freshness in the freezer due to decreased freezer
burn. In addition, the dual evaporation system helps keep food
smells in the refrigerator from transferring to ice in the freezer.
NOTE: The dual evaporation system is always activated when
your refrigerator is operating. You do not need to press any
buttons to turn it on.
Convertible Drawer Temperature Control
(on some models)
The control can be adjusted to properly chill meats or vegetables.
The air inside the pan is cooled to avoid “spot” freezing and can
be set to keep meats at the National Livestock and Meat Board
recommended storage temperatures of 28° to 32°F (-2° to 0°C).
To store meat:
Set the control to one of the three MEAT settings to store meat at
its optimal storage temperature.
To store vegetables:
Set the control to VEG to store vegetables at their optimal storage
temperatures.
NOTE: If food starts to freeze, move the control to the right (less
cold), toward the VEG setting. Remember to wait 24 hours
between adjustments.
Crisper Humidity Control
(on some models)
You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and HIGH.
LOW (open) for best storage of fruits and vegetables with skins.
HIGH (closed) for best storage of fresh, leafy vegetables.
Water and Ice Dispensers
NOTES:
■ The dispensing system will not operate when either door
(refrigerator or freezer) is open.
■ Allow 24 hours for the refrigerator to cool down and chill
water.
■ Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced. Wait 72 hours for full ice
production.
■ The display screen on the dispenser control panel will turn off
automatically and enter “sleep” mode when the control
buttons and dispenser pads have not been used for 2 minutes
or more. While in “sleep” mode, the first press of a control
button will only reactivate the display screen, without
changing any settings.
Flush the Water System
Air in the water dispensing system can cause the water dispenser
to drip. After connecting the refrigerator to a water source or
replacing the water filter, flush the water system. Flushing the
water dispensing system forces air from the water line and filter,
and prepares the water filter for use.
NOTE: As air is cleared from the system, water may spurt out of
the dispenser.
1. Using a sturdy container, depress and hold the water
dispenser pad for 5 seconds, then release it for 5 seconds.
2. Repeat Step 1 until water begins to flow.
3. Once water begins to flow, continue depressing and releasing
the dispenser pad (5 seconds on, 5 seconds off) until a total of
3 gal. (12 L) has been dispensed.
Additional flushing may be required in some households.
Calibrate Measured Fill
Household water pressure may affect the accuracy of the
Measured Fill feature. For optimum performance of your water
dispenser, you must first calibrate Measured Fill.
IMPORTANT: Flush the water system before calibrating Measured
Fill.
1. Place a sturdy measuring cup (1 cup [237 mL] size) on the
dispenser tray, centered in front of the water dispenser pad.
NOTE: Depending on your model, a measuring cup may be
provided.
2. Press and hold the OPTIONS and LOCK buttons at the same
time for 3 seconds. The words “Back” and “1 Cup” will appear
on the display screen. Also, the Calibrate Measured Fill icon
will illuminate and remain lit while the Measured Fill feature is
being calibrated.
NOTE: You may press the ICE MODE button under the word
“Back” at any time to exit calibration mode. The Calibrate
Measured Fill icon will turn off.
3. Using your hand (not the measuring cup), press and release
the water dispenser pad in order to dispense water to the
1 cup fill line.
NOTE: If overfilling or spilling occurs, discard the water and
press “Back” to restart the calibration process.
4. When 1 cup of water has been correctly dispensed into the
measuring cup, press the MEASURED FILL button under the
word “Confirm” to confirm the calibration.
When Measured Fill calibration has been confirmed, the display
will return to the home screen.
Loading ...
Loading ...
Loading ...