HFP 4O22 WG C X UK INSTRUCTION FOR USE

Loading ...

OPTIONS AND SETTINGS

This setting allows you to optimise the performance of the cycle

according to the type of detergent used. Enable it if you use combined

detergents in tablet form (rinse aid, salt and detergent in 1 dose).

To set the Tablet, enter in the setting

menu by pressing „OK” button and

navigate with „< , >” until „TABLET”

is shown, then press „OK” button.

If there are not many dishes to be washed it can be loaded in one rack

only. Using this option you can select which rack you want to wash.

Select a compatible cycle (see “Cycles table”), and then press the

ZONE WASH button: the symbol of the chosen rack will appear on the

display.

By default the ZONE WASH is not active and all racks icons are lit.

Selected only lower rack.

Selected only upper rack.

Thanks to the additional 3D water jets placed on the bottom of the

cavity, 3D ZONE WASH option allows to save energy or to increase the

washing performance of the dishwasher. It is compatible with Normal

and Intensive cycles, and it works with one rack at once.

• 3D ZONE WASH + NORMAL CYCLE: it allows to reduce energy

consumption up to 40%.

• 3D ZONE WASH + INTENSIVE CYCLE: it increases the washing

performances up to 40%. Ideal for very soiled mixed loads, e.g. pans

and saucepans, dishes with heavy encrustation or dicult-to-clean

crockery (grater, vegetable mill, dirty cutlery).

How to activate the option:

1. Select a compatible cycle (Normal or Intensive).

2. Press button to activate/deactive the option: a basket icon will

blink for a few seconds.

3. It is possible to change the selected rack pressing the ZONE WASH

button.

4. Remember to load the crockery in the selected rack only.

The start of the cycle may be delayed for a selected period of time.

To set a delay, enter in the setting menu by pressing „OK” button and na-

vigate with „< , >” until „START DELAY” is shown, then press „OK” button.

With each press of the button “>” or “<“, the delay start increases by:

• every 0:30 if selection below 4 hours,

• every 1:00 if selection is below 12 hours,

• every 2 hours if selection is above 12 hours.

To remove the delay, press „<” or

„>” button until „OFF” is displayed.

Default value is OFF.

If delay is selected, the is lit.

Once „OK” button is pressed the

delay is conrmed and the machine

comes back to the cycle selection

screen with delay value visible.

Close the door and press „START” to start the delay.

This option can be used to reduce the duration of the main cycles

while maintaining washing and drying performance levels.

To set the Turbo, enter in the setting

menu by pressing „OK” button and

navigate with „< , >” until „TURBO” is

shown, then press „OK” button.

With each press of the button „>” or

„<“ option will be ON or OFF.

Conrm by pressing „OK” button.

The KEYLOCK function blocks the

control panel except the „ON/OFF”

button.

To activate the Keylock, enter in the

setting menu by pressing „OK” button

and navigate with „< or >” until

„KEYLOCK” is shown, then press OK.

Once set, to deactivate it keep pressing „OK” button for a few seconds.

This option allows to improve the drying of the dishes using higher

temperature during the nal rinse and an extended drying phase. The

EXTRA DRY option results in the lengthening of the wash cycle.

To set the Extra Dry, enter in the

setting menu by pressing „OK” button

and navigate with „< , >” until

„EXTRA DRY” is shown, then press

„OK” button.

With each press of the button „>” or

„<“ option will be ON or OFF.

Conrm by pressing „OK” button.

TABLET (All-in-one)

TABLET OFF

TABLET ON

ZONE WASH

3D ZONE WASH

3D WASH

DEACTIVATED

3D WASH

ACTIVATED

START DELAY

START DELAY OFF

<STARTS IN h> OFF

<STARTS IN h> 4:00

TURBO

TURBO OFF

TURBO ON

KEYLOCK ACTIVATED

PRESS "OK” FOR 3 SEC.

KEYLOCK

KEEP PRESSED…

KEYLOCK DEACTIVATED

EXTRA DRY

EXTRA DRY OFF

EXTRA DRY ON

With each cycle additional options can be used. A full list of available options working with specic cycles can be found in the Cycle Table on

the previous page. All active options are shown on the display.

To set an option press „OK” button. SET OPTIONS message is shown for a few seconds. Then use „<” or „>” button to navigate through the

option list. Press „OK” to select the option, in the setting menu the LED above „OK” button is lit.

If the option is not available, it will be still visible in its position but with „ ”

Loading ...

INSTRUCTION FOR USE - Page 9