Loading ...
Loading ...
Loading ...
5
Control Panel and Features
POWER
Touch to turn the dryer on and off. Touch to stop/cancel
a cycle at any time.
WHAT TO DRY/HOW TO DRY
First select a cycle from the “What to Dry” (Timed and
Automatic cycles) and then select the “How to Dry” to get
the best combination cycle available for the type of items
you are going to dry. See “Cycle Guide” for cycle details.
START/PAUSE
Touch and hold until the LED comes on to start a cycle,
or touch once while a cycle is in process to pause it.
LED DISPLAY
When you select a cycle, its default settings will light up
and the Estimated Time Remaining (for Automatic Cycles)
will vary depending on “What to Dry” and “How to Dry”
selections or actual time remaining for Timed Dry Cycles
(for Manual Cycles) will be displayed.
MODIFIERS
Use to select available modiers for your dryer. Not all
cycles and options are available on all models.
Temperature
When using Timed Dry Cycle, you may select a dry
temperature based on the type of load you are drying.
Use the warmest setting safe for the garments in the
load. Follow garment label instructions.
NOTE: Automatic Cycles will give you up to
3 temperatures to adjust and it varies, depending
on the “What to Dry” or “How to Dry” selections that
have been made.
Dryness
You may adjust the Dryness on Automatic Cycles
(except for the Sanitize cycle), if desired.
NOTE: Dryness is for use with Automatic Cycles only.
+\- Timed Dry Adjust
Touch “+” or “–” with Timed Dry and Quick Cycles to
increase or decrease the length of the cycle.
EcoBoost™ Feature
Touch to select/deselect the EcoBoost™ feature, which
allows you to increase your energy savings by using a
slightly lower heat level. Savings may vary across load
type. This will increase dry times. The EcoBoost™ feature
will default on for Mixed Normal. It will not be available for
the other cycles; also, the dryer will emit an invalid beep
and Mixed Normal will ash on the control panel if you
try to select the EcoBoost™ feature with another cycle
selected.
1
2
3
4
Not all features and cycles are available on all models.
OPTIONS
Use to select available options for your dryer. Not all
cycles and options are available on all models.
Static Reduce
Touch to add the Static Reduce option to selected
Automatic cycles. The dryer will automatically tumble,
pause, and introduce a small amount of moisture
into the load to help reduce static. This option adds
approximately 8 minutes to the total cycle time.
Audio Level
Use this to change the signal indicating the end
of a drying cycle, as well as the tones that sound
when a feature, setting, or option is touched. Touch
and hold Audio Level for about three seconds to turn
sounds to low, medium, high, or off.
Damp Beep
Touch to select the Damp Beep signal. When
selected, a series of beeps will sound when the load
is damp, but not completely dry. This will allow you
to take clothes out of the load that do not need to dry
completely. This option is available on some cycles.
Signal volume may not be adjusted using the Audio
Level option above, but will sound at the same level
as the End of Cycle signal. The Damp Beep signal is
selected as a default for the Bulky/Sheets cycle as a
reminder to manually reposition bulky loads midway
through the cycle.
Wrinkle Shield™ Option
If you will be unable to remove a load immediately,
touch the Wrinkle Shield™ option to add up to 150
minutes of periodic tumbling to help reduce wrinkling.
You may select the “+ Steam” setting to add a short
steam cycle after 60 minutes to help smooth out
wrinkles.
NOTE: If the Wrinkle Shield™ option is selected, it is
active even if the display shows “END” at the end of
a cycle. If you open the dryer door prior to the end
of the Wrinkle Shield™ option, the dryer will go
into Pause mode. You will need to touch Power
to turn off or touch Start/Pause to continue the
Wrinkle Shield™ option. If the Wrinkle Shield™ option
is paused, it will also time out after 5 minutes of
inactivity and return to Standby.
NOTE: The control panel features a sensitive surface that responds to a light touch of your nger. To ensure your selections are
registered, touch the control panel with your nger tip, not your ngernail. When selecting a setting or option, simply touch its name.
5
1
2
3
6
5
4
7
9
6
8
10
Loading ...
Loading ...
Loading ...