Loading ...
Loading ...
Loading ...
V40BVCBK V40BVCS312
User Manual
If it is left hinge,reverse the door as the same way.
V40/V26/V20 SERIES
UNDER-BENCH INSTALLATION INSTRUCTIONS
1.
Vintec
beverage
Center
dimensions:
V40
Height 820mm – 860mm (40mm adjustable feet)
Width 595mm
Depth 571mm + 30mm stopper (Total of 601mm)
V26
Height 820mm – 830mm (10mm adjustable feet)
Width 380mm
Depth 572mm + 30mm stopper (Total of 602mm)
V20
Height 810mm – 830mm (10mm adjustable feet)
Width 295 – 300mm
Depth 561– 592mm + 30mm stopper (Total of 622mm)
2.
This
Vintec
Beverage
Center
is
not
designed
to
be
fully
integrated
behind
a
joinery
door.
3.
Please
note
that
:
For V40 a minimum cut out width of 615mm is required to facilitate installation,
removal and servicing.
For V26 a minimum cut out width of 400mm is required to facilitate installation,
removal and servicing.
For V20 a minimum cut out width of 320mm is required to facilitate installation,
removal and servicing.
4.
To provide good performance this cabinet requires adequate ventilation. The Vintec
Beverage Center cabinet requires 10mm clearance on both sides, on top; and 30mm
clearance at the rear. (You must fit the b
ack spacer provided, it will ensure the
minimum 30mm clearance at the rear). A ventilation grid needs to be installed in
this 30mm clearance area at the rear. For good ventilation, it is necessary to install a
grill with a minimum size of 200x40mm at the top of the back wall or on either side
at the top r
ear – refer to diagrams on the following pages. This is to allow cooler
fresh air to flow into the 30mm gap at the rear of the cabinet. The ventilation grill
must not be installed close to an oven or next to a s
ealed area without access to
fresh cool air. (Do call Vintec’s Service Department for further explanation. Failure
to comply with the above specifications could void the WARRANTY.)
4.
Remove
decorative
nail
(8)
from
left
top
of
cabinet
and
install
spare
top
hinge
(Left)
(7)
at left top of cabinet with 3 screws. (Fig. D)
5.
Following
the
above
procedure,
install
the
spare
lower
hinge
to
the
left
(9).
(Fig.
E)
6.
I
nstall
and
aligned
the
door.
7.
Insert
the
plastic
caps
to
cover
the
holes(8).
V20BVCBK
1 Lock screws 2 Lower hinge (Right) 3 Door axis
4 Top hinge (Right) 5 Door 6 Cabinet body
7 Top hinge (Left) 8 Lower hinge (Left)
- Unscrew the lock screws (1); (Fig. 1) to remove the door axis located at the bottom.
- While holding the door firmly, pull the door (5) outward and take it out; (Fig. 2)
- Remove the 3 bolts and take out the right top hinge (2); (Fig. 3)
- Fix the left top hinge and the bottom left hinge with the bolts as per Fig. 4,
- Re-install the door the same way it was removed and fix back the door axis.
- While holding the door firmly, remove the three lock screws (2) from the lower
right hinge module, and remove it.
!
Fig.1)
- Remove the three lock screws (4) from the top right hinge and remove the hinge
(3) . (Fig.3)
- Fix the top left hinge (5) at the top left corner with the three lock screws (4) . (Fig.4)
- While holding the door, insert the axis core into the door’s (7) upper left hinge
hole. Fix the left bottom hinges by inserting the axis core first into the door’s lower
left hinge hole (6). Then secure the lower le
ft hinge to finish the door replacement.
(Fig. 5)
V40BVCS3 / V40BVCBK
1. Lower hinge (Right) 2 . Screws 3 .Door axis
4. Door 5. Top hinge (Right) 6. Hinge Screws
7. Top hinge (Left) 8. Decorative nail 9. Lower hinge (Left)
10. Door limit device 11. Screw
1.
Open
the
door
to
90
degree
angle,
take
out
the
2
screws
(2)
from
lower
door
axis
(3),
remove the door (4), Remove the axis plate (3) from the door, (Fig. A).
2.
U
nscrew
the
screw
(11)
located
underneath
the
door
frame
and
the
limit
device
(10),
and re locate it at left end side of the door frame. (Fig. A/B)
3.
Take
out
the
3
hinge
screws
(6)
from
the
top
hinge
(right)
(5)
and
remove
it.
(Fig.
C)
Loading ...
Loading ...
Loading ...