Loading ...
Loading ...
Loading ...
13
MARK HOLES
Select the vent option that your installation will
require and proceed to that section:
Hood mounting screws (4)
13
15
⁄16″ (30″ hood)
16
15
⁄16″ (36″ hood)
13
15
⁄16
″
(30
″
hood)
16
15
⁄16
″
(36
″
hood)
Cabinet front
Center
line
Electrical access hole
(in cabinet bottom)
Wood shims
(recessed-
bottom cabinets only)
Vertical duct
access hole
10
1
⁄2″
1
1
⁄4″
2″
12
9
⁄16″
5″
1
1
⁄4″
A.
Outside top exhaust
(Vertical duct–3
1
⁄4
″
x 10
″
Rectangular)
• Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
B.
Outside top exhaust (Vertical duct–7″ Round)
• Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Hood mounting screws (4)
13
15
⁄16″ (30″ hood)
16
15
⁄16″ (36″ hood)
13
15
⁄16
″
(30
″
hood)
16
15
⁄16
″
(36
″
hood
)
Cabinet front
Center
line
Electrical access
hole
(in cabinet bottom)
Wood shims
(recessed-
bottom cabinets only)
Access
hole for 7″
round duct
10
1
⁄2″
1
1
⁄2″
1
1
⁄4″
12
1
⁄2″
5″
Cabinet
bottom
8″ DIA.
HOLE
CHOOSE VENTING OPTION
(for JV5 Series models only)
Cabinet Bottom
9
10
Wood shims (recessed-bottom cabinets only)
Cabinet front
Center line
Electrical access hole
(in wall)
Hood mounting screws (4)
Horizontal duct
access hole
Cabinet
bottom
13
15
⁄16″ (30″ hood)
16
15
⁄16″ (36″ hood)
1
7
⁄16″
1
⁄8″
3
3
⁄
4
″
5
1
⁄
4
″
5
1
⁄4″
12
7
⁄
16
″
13
15
⁄16″ (30″ hood)
16
15
⁄16″ (36″ hood)
C.
Outside rear exhaust
(Horizontal duct–3
1
⁄4
″
x 10
″
Rectangular)
• Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
D.
Recirculating (non-vented ductless–
Available on JV5 Series models only)
• Use the hood as a template and mark the locations
on the cabinet for the electrical wiring and keyhole
screw slots.
• Since the hood is to be recirculated (not to be vented
outside), do not cut out any vent openings in the wall
or cabinet bottom.
The hood can be set to vent outside or to recirculate
air back into the kitchen.
The plastic vent lever is located near the center of the
hood opening.
• To vent to the outside, make sure the plastic vent
lever is in the HORIZONTAL position (flat against
the metal top of the hood).
• To recirculate air into the kitchen, make sure the
plastic vent lever is in the VERTICAL position
(flat against the plastic blower housing).
NOTE: In order to change the vent lever position,
you will need to pull the lever out slightly to clear
the plastic tabs.
5
1
⁄4″
5
1
⁄4″
Installation Instructions
Set for
outside venting
Set for
recirculating
Stop tab
Hood shown lying upside down
Stop tab
Loading ...
Loading ...
Loading ...